Cisco WS-X4232 Hardware Maintenance Manual - Page 131

For example, Cisco 4500-M and Cisco 4700 ROM Monitor

Get Cisco WS-X4232 - Catalyst 4232 - Switch PDF manuals and user guides
UPC - 746320172057
View all Cisco WS-X4232 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Entering the ROM Monitor Program For example: rommon 7 > confreg Configuration Summary enabled are: console baud: 9600 boot: the ROM Monitor do you wish to change the configuration? y/n [n]: y enable "diagnostic mode"? y/n [n]: y enable "use net in IP bcast address"? y/n [n]: enable "load rom after netboot fails"? y/n [n]: enable "use all zero broadcast"? y/n [n]: enable "break/abort has effect"? y/n [n]: enable "ignore system config info"? y/n [n]: change console baud rate? y/n [n]: y enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400 [0]: 0 change the boot characteristics? y/n [n]: y enter to boot: 0 = ROM Monitor 1 = the boot helper image 2-15 = boot system [0]: 0 Configuration Summary enabled are: diagnostic mode console baud: 9600 boot: the ROM Monitor do you wish to change the configuration? y/n [n]: You must reset or power cycle for new config to take effect Cisco 4500-M and Cisco 4700 ROM Monitor D-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
Cisco 4500-M and Cisco 4700 ROM Monitor
D-5
Entering the ROM Monitor Program
For example:
rommon 7 >
confreg
Configuration Summary
enabled are:
console baud: 9600
boot: the ROM Monitor
do you wish to change the configuration? y/n
[n]:
y
enable
“diagnostic mode”? y/n
[n]:
y
enable
“use net in IP bcast address”? y/n
[n]:
enable
“load rom after netboot fails”? y/n
[n]:
enable
“use all zero broadcast”? y/n
[n]:
enable
“break/abort has effect”? y/n
[n]:
enable
“ignore system config info”? y/n
[n]:
change console baud rate? y/n
[n]:
y
enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400
[0]:
0
change the boot characteristics? y/n
[n]:
y
enter to boot:
0 = ROM Monitor
1 = the boot helper image
2-15 = boot system
[0]:
0
Configuration Summary
enabled are:
diagnostic mode
console baud: 9600
boot: the ROM Monitor
do you wish to change the configuration? y/n
[n]:
You must reset or power cycle for new config to take effect