Cobra MR HH150 FLT MR HH150 FLT Manual - English - Page 15
Memory Location Scan Mode
View all Cobra MR HH150 FLT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
VOHpFerMatainrgineYoRuardRioadPirootocols Intro Operation MEM Icon Secondary Icons Installation Advanced Operation Customer Warranty TAossiRstaencceall a Stored Memory Location: 1.Press the Memory/Escape button. The MEM icon will be turned On. 2. Press Customer Assistance the Channel Up or Channel Down button to select the memory location. If a memory location has been programmed, its associated channel will display on the LCD. Your radio is now in Marine Standby mode on the selected memory location. Notice ToCaEutxionit MemWoarryninLg ocation Mode: Press the Memory/Escape button to return the radio to Marine Standby mode. The last channel used in Marine Standby mode will now be displayed on the LCD and the MEM icon will disappear. To Erase Stored Memory Locations: 1. Press and hold the Memory/Escape button for two seconds. The memory location number will start flashing and the MEM icon will be turned On. 2. Use the Channel Up and Channel Down buttons to advance to the memory location you want to erase. 3. Press the Memory/Escape button to select the memory location. The memory channel number will stop flashing and the channel number will start flashing. 4. Use the Channel Up and Channel Down buttons to change the channel to read "--" at the selected memory location. 5. Press the Memory/Escape button to erase that memory location. Repeat steps 2 through 5 to erase as many additional memory locations as you want. 6. Press and hold the Memory/Escape button for two seconds. This will return the radio to Memory mode. 7. Press and release the Memory/Escape button again to return to Marine Standby mode. Main Icons Advanced Operation VOHpFerMatainrgineYoRuardRioadPirootocols Intro Memory Location Scan Operation Customer Warranty Memory Assistance Location Scan Mode Intro Operation DuCArsuissnitsotgmanecrMe emoWarryrantLy ocation Scan mode, the radio will rapidly scan through all programmed memory channels. Whenever Secondary Icons Installation Installation aCnusytomaecr tivity is detected on a channel, the radio will stop the scan for Assistance Customer 10 seconds to allow you to listen briefly on that chaAsnsisntaencle. It will then continue to scan unless you switch out of Secondary Icons Memory Location Scan mode. Notice Notice NOTE IfCatuhtieonre are fWeawrninegr than two memory locations programmed in tChauetionradio, WtharneingMemory Location Scan option will not be available. At least two memory locations need to be programmed to use the Scan button. FLOATING MARITNo EEnter MHeHmo1ry5Lo0cation Scan: MEM/ESC Button 1. From Marine Standby mode, press the Memory/Escape button. FELSOCATINWGEAM2T. PTHAhreeERsrsRaIadNniodEwhoiSllldiEmHthTmeHUeDd1UiPaAt5eLl0yWbAeTgCinH/tSoCsAcNanbaultltopnre. -assigned PWR MEM ESC H-MWmt-hLeeEmLACorDTy. HchEaEnRnNelTs.ETRhSeESTCAUNPand MEM icons will show on 3. A signal on any channel will stop the scan for PWR Scan Button SC/DW CMHEAMNNEL 4. 10 seconds to allow you to listen to the traffic oP nreHtshs-aMtthleo-cLCaht+iaon1nn.6el ENTER Up or Channel Down button SC/DW VOL CHAtNo rNesEuLme scanning the Memory Location Scan channels or to change the scan direction. 5. To EXIT MVemOoLry Loc+at1io6n Scan mode, press and hold the DUAL WATCH/SCAN button again. The SCAN and MEM icons will disappear from the LCD and the radio will return VOL to Memory mode.VOL SUBMERSIBLE SUBMERSIBLE 24 English Nothing Comes Close to a Cobra® 25