Compaq 215999-002 Compaq Deskpro EX and Deskpro EXS Series of Personal Compute - Page 36

Power Switch Assembly, CAUTION, WARNING

Get Compaq 215999-002 - Deskpro EX - 64 MB RAM PDF manuals and user guides
UPC - 720591550486
View all Compaq 215999-002 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

4.9 Power Switch Assembly CAUTION: The power switch should not be removed from the switch holder. Doing so may damage the switch components. 1. Prepare the computer for disassembly (Section 4.2). WARNING: Power is continuous to the system board and power supply even when the power switch is turned off. To prevent damage to the unit, disconnect the power cord from the power source or the unit before beginning disassembly procedures. 2. Lay the computer down on its large base for greater stability. 3. Remove the access panel (Section 4.5). 4. Remove the front bezel (Section 4.6). 5. Disconnect the power/LED cable from the system board 1. 6. Push the release tab 2 toward the drive bays, then remove the power switch assembly from the chassis. To install the new power switch, reverse the above procedure, pushing the switch assembly until it snaps into place. The power/LED connector is keyed to ensure proper installation. Compaq Deskpro EX and Deskpro EXS Series of Personal Computers 4-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Compaq Deskpro EX and Deskpro EXS Series of Personal Computers
4-9
4.9
Power Switch Assembly
CAUTION:
The power switch should not be removed from the switch holder. Doing so may
damage the switch components.
1.
Prepare the computer for disassembly (Section 4.2).
WARNING:
Power is continuous to the system board and power supply even when the power
switch is turned off. To prevent damage to the unit, disconnect the power cord from the power
source or the unit before beginning disassembly procedures.
2.
Lay the computer down on its large base for greater stability.
3.
Remove the access panel (Section 4.5).
4.
Remove the front bezel (Section 4.6).
5.
Disconnect the power/LED cable from the system board
1
.
6.
Push the release tab
2
toward the drive bays, then remove the power switch assembly
from the chassis.
To install the new power switch, reverse the above procedure, pushing the switch
assembly until it snaps into place. The power/LED connector is keyed to ensure proper
installation.