Compaq 215999-002 Compaq Deskpro EX and Deskpro EXS Series of Personal Compute - Page 44

Removing a PCI Expansion Board, until the connectors pull free from the slot.

Get Compaq 215999-002 - Deskpro EX - 64 MB RAM PDF manuals and user guides
UPC - 720591550486
View all Compaq 215999-002 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

4.11.2 Removing a PCI Expansion Board 1. Prepare the computer for disassembly (Section 4.2). WARNING: Power is continuous to the system board and power supply even when the power switch is turned off. To prevent damage to the unit, disconnect the power cord from the power source or the unit before beginning disassembly procedures. 2. Lay the computer down on its large base for greater stability. 3. Remove the access panel (Section 4.5). 4. Disconnect any cables from the expansion board, noting their location for reinstallation. 5. Remove the expansion board retaining screw. 6. Hold the board at each end and carefully rock it back and forth while pulling upward until the connectors pull free from the slot. Be sure not to scrape the card against other components 7. If not installing another expansion board in the slot, then close off the open slot by installing an expansion slot cover with a screw. Compaq Deskpro EX and Deskpro EXS Series of Personal Computers 4-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Compaq Deskpro EX and Deskpro EXS Series of Personal Computers
4-17
4.11.2
Removing a PCI Expansion Board
1.
Prepare the computer for disassembly (Section 4.2).
WARNING:
Power is continuous to the system board and power supply even when the power
switch is turned off. To prevent damage to the unit, disconnect the power cord from the power
source or the unit before beginning disassembly procedures.
2.
Lay the computer down on its large base for greater stability.
3.
Remove the access panel (Section 4.5).
4.
Disconnect any cables from the expansion board, noting their location for reinstallation.
5.
Remove the expansion board retaining screw.
6.
Hold the board at each end and carefully rock it back and forth while pulling upward
until the connectors pull free from the slot.
Be sure not to scrape the card against other
components
7.
If not installing another expansion board in the slot, then close off the open slot by
installing an expansion slot cover with a screw.