Craftsman 975LM Owners Manual

White Safety

Sensor Wires

White Connection

Wire to Terminal

Repeat with white/black wires.

White Connection Wire

Black/White

Connection Wire

Wire Nut

(provided)

White Parking

Assist Wires

Quick-Connect Terminals

Red

White

Grey

Model 975LM and 975LMC

Liftmaster Laser Garage

Parking Assist

Owner’s Instructions

Parking Assist

Swivel Mount

White Safety

Sensor Wires

White Parking

Assist Wire

Quick-Connect Terminals

Red

White

Grey

Repeat with white/black wires.

White Connection Wires

Black/White

Connection Wires

INSTALLATION

1. Open your garage door and park your vehicle outside of

the garage.

2. Determine the mounting location on or near the ceiling

and fasten the parking assist using the screw and anchor

provided (Figure 1).

3. Depress tabs under the wires and temporarily remove

the white and white/black safety sensor wires from the

garage door opener.

4.

Stripping the wires prior to installation:

If installing one parking assist:

Separate white and

white/black wires and strip 7/16" (11 mm) of insulation

from the parking assist wires.

If installing two parking assists:

Cut 6" (15 cm) of

wires from the end of one of the parking assist wires for

use as connection wires. Separate white and white/black

wires and strip 7/16" (11 mm) of insulation from both ends

of the connection wire.

5.

Connecting the wires to install:

If installing one parking assist:

Twist like colored wires

for the parking assist and the safety sensors together.

Insert twisted wires into quick-connect holes: white to

white and white/black to grey (Figure 2).*

If installing two parking assists:

Separate white and

white/black wires and strip 7/16" (11 mm) of insulation

from the end of the parking assist wires. Twist like

colored wires for the parking assist, safety sensors and

connection wire together. Secure with wire nut (provided).

Insert loose end of connection wires into quick-connect

holes: white to white and white/black to grey (Figure 3).*

*

Please reference your garage door opener owner’s

manual for proper wire installation.

SET UP AND ADJUSTMENT

1. Drive your vehicle into the garage and park in the location

you want to park your vehicle each time (Figure 4).

2. Activate the parking assist locator by obstructing the path

of the safety reversing sensors. The laser will emit a

pulsing bright red beam. Using the swivel mount, aim the

red beam to a location on the dash or hood that can

easily be seen while seated in the driver°s seat.

NOTE:

The laser will shut off automatically in 1 minute. If

you are not finished adjusting the beam and it turns off,

simply obstruct the path of the safety reversing sensors

again to re-activate the beam.

3. Sit in the driver°s seat and confirm that you can easily

see the location of the red beam. This location is now

your point of reference for parking your vehicle (Figure 5).

CAUTION: Do not stare directly into the beam.

Repeat

steps for installation on optional 2nd laser accessory kit.

To avoid eye INJURY or damage to product:

• NEVER point the laser at anyone.

• NEVER look directly into the laser beam.

• NEVER disassemble the laser.

• The parking assist is NOT a substitute for safe parking

practices.

• Use of controls or adjustments, or the performance or

procedures other than specified can result in hazardous

radiation exposure.

• ONLY for use on Chamberlain manufactured garage door

openers.

CAUTION

Figure 1

Parking Assist (1)

Wire Nuts (2)

Labels (2) Not Shown

Screw 6ABx1-1/4" (1)

Anchor (1)

Assistance de Garage (1)

Écrou pour Fils

(2)

Vis 6ABx1-1/4 po (1)

Guía de Estacionamiento (1)

Capuchones de Emplame (2)

Tornillo 6ABx1-1/4 de pulg. (1)

Figure 2

Figure 3

Carton Inventory

Section	Page
English	1
INSTALLATION	1
SET UP AND ADJUSTMENT	1
OPERATION	2
TROUBLESHOOTING	2
French	3

Craftsman 975LM Owners Manual

Craftsman 975LM - Sears Lift-Master Double Laser Garage Parking Assistant Manual

Craftsman 975LM manual content summary: