Cub Cadet RZT L 34 Operation Manual - Page 11

Oil Service

Get Cub Cadet RZT L 34 PDF manuals and user guides View all Cub Cadet RZT L 34 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Oil Service • Check oil level regularly. • Be sure correct oil level is maintained. Check every five to ten hours before starting engine. See oil checking procedure in the Set-Up section. Oil Drain IMPORTANT: Be sure to check engine on a level surface with the engine stopped. Drain the oil while the engine is still warm to assure rapid and complete draining. 1. Remove all fuel from tank by running engine until it stops from lack of fuel. 2. Remove drain plug and allow oil to drain into a suitable container. See Figure 6-1. NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground. Replace Oil Filter This engine is equipped with a spin-on oil filter that should be replaced each time an oil change is performed, every season or 50 hours. Refer to Figure 6-2. Oil Fill Cap Oil Filter Figure 6-2 1. Drain oil. See oil drain section. 2. Drain Plug 3. 4. Figure 6-1 WARNING: Before tipping engine or equipment to drain oil, drain fuel from tank by running engine 5. until fuel tank is empty. 6. Remove oil filter. Dispose of old oil filter properly. Lube gasket of new oil filter with clean oil. Install and turn oil filter by hand until the gasket comes in contact with the sealing surface of the crankcase cover, then tighten the oil filter, 10-12 Nm (88.5-106.2 in-lb), 1/23/4 turn. Add oil. See add oil section. Make sure dipstick is installed. 3. Reinstall the drain plug and tighten it securely, 12-14 Nm 7. Start and run engine. Check for leaks. (106.2-123.9 in-lb). 8. Stop engine. Wait a few minutes and check the oil level. IMPORTANT: Used motor oil may cause skin cancer if repeatedly See checking oil level section. left in contact with the skin for prolonged periods. Although this 9. Install and tighten dipstick. is unlikely unless you handle used oil on a daily basis, it is still advisable to thoroughly wash your hands with soap and water as soon as possible after handling used oil. Section 6 - Maintenance 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
11
S
ECTION
6 — M
AINTENANCE
Oil Service
•
Check oil level regularly.
•
Be sure correct oil level is maintained. Check every five
to ten hours before starting engine. See oil checking
procedure in the Set-Up section.
Oil Drain
IMPORTANT:
Be sure to check engine on a level surface with the
engine stopped. Drain the oil while the engine is still warm to
assure rapid and complete draining.
1.
Remove all fuel from tank by running engine until it stops
from lack of fuel.
2.
Remove drain plug and allow oil to drain into a suitable
container. See Figure 6-1.
Oil Fill Cap
Drain
Plug
Figure 6-1
WARNING:
Before tipping engine or equipment to
drain oil, drain fuel from tank by running engine
until fuel tank is empty.
3.
Reinstall the drain plug and tighten it securely, 12-14 Nm
(106.2-123.9 in-lb).
IMPORTANT:
Used motor oil may cause skin cancer if repeatedly
left in contact with the skin for prolonged periods. Although this
is unlikely unless you handle used oil on a daily basis, it is still
advisable to thoroughly wash your hands with soap and water as
soon as possible after handling used oil.
NOTE:
Please dispose of used motor oil in a manner that is
compatible with the environment. We suggest you take it in a
sealed container to your local service station for reclamation. Do
not throw it in the trash or pour it on the ground.
Replace Oil Filter
This engine is equipped with a spin-on oil filter that should be
replaced each time an oil change is performed, every season or
50 hours. Refer to Figure 6-2.
Oil Filter
Figure 6-2
1.
Drain oil.
See oil drain section.
2.
Remove oil filter.
Dispose of old oil filter properly.
3.
Lube gasket of new oil filter with clean oil.
4.
Install and turn oil filter by hand until the gasket comes in
contact with the sealing surface of the crankcase cover,
then tighten the oil filter, 10-12 Nm (88.5-106.2 in-lb), 1/2-
3/4 turn.
5.
Add oil.
See add oil section.
6.
Make sure dipstick is installed.
7.
Start and run engine.
Check for leaks.
8.
Stop engine.
Wait a few minutes and check the oil level.
See checking oil level section.
9.
Install and tighten dipstick.