D-Link 900W Manual - Page 31

ASSIGNING AND OPENING VIRTUAL SERVER PORTS, Open Virtual Server Ports To Enable Remote Image Viewing - dcs port forwarding

Get D-Link 900W - DCS Network Camera PDF manuals and user guides
UPC - 790069262852
View all D-Link 900W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

DCS-900W Configuration (continued) Installing the DCS-900W Behind a Router ASSIGNING AND OPENING VIRTUAL SERVER PORTS 5) Open Virtual Server Ports To Enable Remote Image Viewing The Virtual Server Ports of your router must be opened for remote access to your camera. This is also referred to as port forwarding. Please proceed as follows: • Select Enabled to enable virtual server settings. • Select a camera name. • Enter your camera's Local IP Address in the Private IP field. • Select TCP under Protocol Type. • If you are using the default camera port settings, enter 80 in to the Public and Private Port section*. • Schedule should be set to Always so that the camera images can be accessed at any time. • In the Virtual Servers List, a check mark appearing before the camera name will indicate that the ports are enabled. • Click Apply to save your settings. Note: If you are installing multiple cameras, be sure to open a port per additional camera installed: port 81, 82, etc. for web server. Opening Virtual Server Ports on Your Router 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
31
ASSIGNING AND OPENING VIRTUAL SERVER PORTS
5) Open Virtual Server Ports To Enable Remote Image Viewing
Opening Virtual Server Ports on Your Router
The Virtual Server Ports of your router must be opened for remote access to
your camera. This is also referred to as port forwarding.
Please proceed as
follows:
•
Select
Enabled
to enable virtual server settings.
•
Select a camera name.
•
Enter your camera’s Local IP Address in the
Private IP
field.
•
Select
TCP
under
Protocol Type
.
•
If you are using the default camera port settings, enter 80 in to the
Public
and
Private
Port section*.
•
Schedule
should be set to
Always
so that the camera images can
be accessed at any time.
•
In the
Virtual Servers List
, a check mark appearing before the
camera name will indicate that the ports are enabled.
•
Click
Apply
to save your settings. Note: If you are installing multiple
cameras, be sure to open a port per additional camera installed:
port
81, 82, etc. for web server.
Installing the DCS-900W Behind a Router
DCS-900W Configuration
(continued)