Danby DPAC120068 Owners Manual - Page 19

Timer, On/Off

Get Danby DPAC120068 PDF manuals and user guides View all Danby DPAC120068 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Remote Control Operating Instructions 1. Sending Signal: The remote control must be aimed directly at the infra-red eye located below control panel when initiating a command. When the remote control is switched on and a button is pressed, a beep will sound (main unit) confirming a signal was sent/received. All program selections appearing in the remote control display will appear in the display of the main unit when both units are operational. If the main unit does not respond to the command issued, try the procedure again. If the main unit again fails to respond; Check the following: • Are the receiver and the remote unit within the required 7 meter (23 ft.) operating distance? • Is the receiver window on the main unit partially blocked and/or obscured? • Are the batteries correctly installed inside the remote (positive+ / negative-)? • Check the batteries. If low, replace. 2. Setting/Adjusting Time of Day Clock (Remote Control): When the batteries are first installed, the clock display flashes "0:00". Press the M (minute) button to set the correct time in minutes. Each time the M button is pressed the time is increased in 10 minute increments. The time sets automatically (stops flashing) after 5 seconds. Press/hold the H (hour) button to select/change the correct hour time. (time flashes) Each time the H button is pressed the time will increase in 1 hour increments. The time automatically sets (stops flashing) after 5 seconds. When the main unit is swithed on using the remote control, the time on the main unit will automatically adjust to the time set on the remote control. 3. Mode Setting: Press the "Mode" button to select operating mode. Each time the button is pressed will advance to a different setting i.e Auto-Cool-Dry-Fan. MODE ICONS * COOL 44 FAN O DRY 4. Temperature Setting: Press the remote buttons to select the desired °C/°F operating temperature. V Each time a button is pressed the temperature will increase/decrease 1°C/F. The temperature selected will appear in the remote display. When the main unit is switched on using the remote control, the temperature on the main unit will automatically adjust to the temperature set on the remote control. Temperature ranges from 16°C-31°C (60.8°F - 88°F) 5. Fan Speed Setting: Press the "Fan" button to select the operating fan speed. Depending on the mode selection, the fan button will advance to a different fan speed (Auto-Low-Medium -High) The fan speed selected will appear in the display window. FAN SPEED ICONS LOW MEDIUM HIGH MODE Cool Dry Fan AUTO AVAILABLE FAN SPEEDS Low-Medium-High Low Low-Medium-High Low-Medium-High LCD Window 0 Timer On/Off 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
Remote
Control
Operating
Instructions
1.
Sending
Signal:
The
remote
control
must
be
aimed
directly
at
the
infra
-red
eye
located
below
control
panel
when
initiating
a
command.
When
the
remote
control
is
switched
on
and
a
button
is
pressed,
a
beep
will
sound
(main
unit)
confirming
a
signal
was
sent/received.
All
program
selections
appearing
in
the
remote
control
display
will
appear
in
the
display
of
the
main
unit
when
both
units
are
operational.
If
the
main
unit
does
not
respond
to
the
command
issued,
try
the
procedure
again.
If
the
main
unit
again
fails
to
respond;
Check
the
following:
•
Are
the
receiver
and
the
remote
unit
within
the
required
7
meter
(23
ft.)
operating
distance?
•
Is
the
receiver
window
on
the
main
unit
partially
blocked
and/or
obscured?
•
Are
the
batteries
correctly
installed
inside
the
remote
(positive+
/
negative-)?
•
Check
the
batteries.
If
low,
replace.
2.
Setting/Adjusting
Time
of
Day
Clock
(Remote
Control):
When
the
batteries
are
first
installed,
the
clock
display
fl
ashes
"0:00".
Press
the
M
(minute)
button
to
set
the
correct
time
in
minutes.
Each time
the
M
button
is
pressed
the
time
is
increased
in
10
minute
increments.
The
time
sets
automatically
(stops
fl
ashing)
after
5
seconds.
Press/hold
the
H
(hour)
button
to
select/change
the
correct
hour
time.
(time
fl
ashes)
Each
time
the
H
button
is
pressed
the
time
will
increase
in
1
hour
increments.
The
time
automatically
sets
(stops
fl
ashing)
after
5
seconds.
When
the
main
unit
is
swithed
on
using
the
remote
control,
the
time
on
the
main
unit
will
automatically
adjust
to
the
time
set
on
the
remote
control.
3.
Mode
Setting:
Press
the
"Mode"
button
to
select
operating
mode.
Each
time
the
button
is
pressed
will
advance
to
a
different
setting
i.e
Auto
—Cool
—Dry
—Fan.
MODE
ICONS
*
COOL
44
FAN
O
DRY
4.
Temperature
Setting:
Press
the
remote
buttons
to
select
the
desired
°C/°F
operating
temperature.
Each time
a
button
is
pressed
the
temperature
will
increase/decrease
1°C/F.
The
temperature
selected
will
appear
in
the
remote
display.
When
the
main
unit
is
switched
on
using
the
remote
control,
the
temperature
on
the
main
unit
will
automatically
adjust
to
the
temperature
set
on
the
remote
control.
Temperature
ranges
from
16°C
-31°C
(60.8°F
-
88°F)
V
5.
Fan
Speed
Setting:
Press
the
"Fan"
button
to
select
the
operating
fan
speed.
Depending
on
the
mode
selection,
the
fan
button
will
advance
to
a
different
fan
speed
(Auto
—Low
—Medium
—High)
The
fan
speed
selected
will
appear
in
the
display
window.
FAN
SPEED
ICONS
LOW
MEDIUM
HIGH
MODE
Cool
Dry
Fan
AUTO
AVAILABLE
FAN
SPEEDS
Low
-Medium
-High
Low
Low
-Medium
-High
Low
-Medium
-High
LCD
Window
0
Timer
On/Off
18