Dell DR4300e NetVault Backup - Setting Up the DR Series System as an RDA or VT - Page 2

Revisions

Date

Description

January 2014

Initial release

May 2014

Updated to add suggested block size on NVBU device configuration.

April 2015

Added VTL Content for v3.2 Release

This document is for informational purposes only and may contain typographical errors and technical inaccuracies.

The content is provided as is, without express or implied warranties of any kind.

© 2015 Dell Inc. All rights reserved. Reproduction of this material in any manner whatsoever without the express

written permission of Dell Inc. is strictly forbidden. For more information, contact Dell.

PRODUCT WARRANTIES APPLICABLE TO THE DELL PRODUCTS DESCRIBED IN THIS DOCUMENT MAY BE FOUND AT:

http://www.dell.com/learn/us/en/19/terms-of-sale-commercial-and-public-sector

Performance of network reference

architectures discussed in this document may vary with differing deployment conditions, network loads, and the like.

Third party products may be included in reference architectures for the convenience of the reader. Inclusion of such

third party products does not necessarily constitute Dell’s recommendation of those products. Please consult your Dell

representative for additional information.

Trademarks used in this text:

Dell™, the Dell logo, and PowerVault™ are trademarks of Dell Inc. Other Dell trademarks may be used in this

document. Microsoft

®

, Windows

®

, Windows Server

®

, Internet Explorer

®

, MS-DOS

®

, Windows Vista

®

and Active

Directory

®

are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other

countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the

marks and/or names or their products and are the property of their respective owners. Dell disclaims proprietary

interest in the marks and names of others.

Section	Page
1 Installing and configuring the DR Series system for use with NetVault Backup	6
1.1 NetVault software prerequisites	6
1.2 Installing and configuring the DR Series system	6
2 Creating and configuring the RDA target container(s) for NetVault Backup	10
2.1 Adding the RDA target container(s) for NetVault Backup	11
2.2 Configuring transport modes for NetVault Backup	14
2.2.1 Setting the mode using the CLI	14
2.2.2 Setting the mode using the GUI	14
2.3 Configuring a backup job for NetVault Backup	16
3 Configuring VTL	17
3.1 Creating and configuring iSCSI target container(s) for NetVault Backup	17
3.1.1 Create an iSCSI VTL container for NetVault Backup	17
3.1.2 Configure the iSCSI target – Windows	19
3.1.3 Configure NetVault Backup to use the newly created iSCSI VTL	23
3.2 Creating and configuring NDMP target container(s) for NetVault Backup	25
3.2.1 Create the NDMP VTL container for NetVault Backup	25
3.2.2 Set up NetVault Backup to use the newly created NDMP VTL	27
4 Setting up the DR Series system cleaner	30
5 Monitoring deduplication, compression, and performance	31
A VTL configuration guidelines	32
A.1 Managing VTL protocol accounts and credentials	32
A.1.1 iSCSI account details and management	32
A.1.2 NDMP account details and management	33
A.1.3 VTL Default Account Summary Table:	34
A.2 Managing VTL media and space use	34
A.2.1 General performance guidelines for DMA configuration	34
A.2.2 Physical DR space sizing and planning	34
A.2.3 Logical VTL geometry and media sizing	35
A.2.4 Media retention and grouping	36
A.2.5 VTL media count guidelines	36
A.2.6 Adding media to the VTL container	37
A.2.7 Updating NetVault Backup to identify newly added VTL media	37

Dell DR4300e NetVault Backup - Setting Up the DR Series System as an RDA or VT - Page 2

Revisions

Page 2 highlights