Dell Force10 S25-01-GE-24P Setup and Buffer Tuning of the S25P for Storage Env
Dell Force10 S25-01-GE-24P Manual
View all Dell Force10 S25-01-GE-24P manuals
Add to My Manuals
Save this manual to your list of manuals |
Dell Force10 S25-01-GE-24P manual content summary:
- Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 1
. For details on management, see the Management chapter in the FTOS Configuration Guide for the S-Series and the Control and Monitoring chapter in the FTOS Command and from the Documentation tab of iSupport at the Force10 Networks website: https://www.force10networks.com/CSPortal20/KnowledgeBase - Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 2
Software Version : 7.8.1.0 Unit Type Serial Number Part Number Revision * 0 S25-01-GE-24P DL277000000 7590004800 B 0 S50-PWR-AC N/A N/A N/A 0 S50-FAN N/A N/A N/A * - Management Unit Software Protocol Configured Force10> If your system does not have the correct software version - Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 3
the part that displays the result of using the commands, above: Force10#show run Current Configuration ... ! Version 7.8.1.0 ! Last configuration change setting passwords, see the Getting Started chapter in the FTOS Configuration Guide for the S-Series and the Security chapter in the FTOS Command - Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 4
output truncated Force10#show ip interface brief Interface IP-Address OK Method Status GigabitEthernet 0/0 unassigned NO Manual up GigabitEthernet 0/1 unassigned NO Manual up GigabitEthernet 0/2 unassigned NO Manual up GigabitEthernet 0/3 unassigned NO Manual up GigabitEthernet - Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 5
prevent packet drops during a temporary burst of traffic. Force10 recommends the following buffer profile configuration for high-performance storage Ethernet Pause Frames, see that Release Notes document and the FTOS Configuration Guide for the S-Series. Figure 1 Buffer Carving for 1Gig Interfaces in - Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 6
queue3 3 queue4 3 queue5 3 queue6 3 queue7 3 buffer dynamic 1257 Force10# Figure 3 Configuring Internal ASIC Buffers in Stack Unit 0 ! buffer fp- hig buffer fp-uplink stack-unit 0 port-set 1 buffer-policy eql-hig Force10# Figure 4 Applying the Buffer Profile to all 1Gig and 10Gig Ports ! interface range - Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 7
To apply the configuration, above, to other stack members, use the following commands. The interface range used and port-pipes ("port-set 0-1") designated would depend on the S-Series model. The following sequence presumes that the subject stack member is an S25P model. For an example of configuring - Dell Force10 S25-01-GE-24P | Setup and Buffer Tuning of the S25P for Storage Env - Page 8
8 Basic Layer 2 Setup and Buffer Tuning of the S25P for Storage Environments
101-00337-00
1
Basic Layer 2 Setup and Buffer Tuning of the
S25P for Storage Environments
Introduction
This document is intended for the users of S-Series S25P switches running FTOS 7.8.1.0 and configured
for use in a storage environment. This document describes:
•
Using the console port to enable all ports on the switch for Layer 2 switching
•
Verifying that the installed FTOS software is FTOS 7.8.1.0
•
Setting up passwords for managing the switch. For details on management, see the Management
chapter in the
FTOS Configuration Guide for the S-Series
and the Control and Monitoring chapter in
the
FTOS Command Reference
for the S-Series
.
•
Optimizing the buffer for use in pure storage environments
This document does not cover:
•
Installing optional modules. For installation details, see the document
Installing S25P Systems
. For a
configuration example, see
Figure 7 on page 6
here.
•
Adding the switch to an S-Series stack. For stacking configuration details, see the Stacking chapters in
the
Configuration Guide
and the
Command Reference
listed above.
•
Layer 3 (IP addressing) configuration. For details, see the Interfaces and IP Addressing chapters in the
Configuration Guide
and Interface Commands chapter in the
Command Reference
listed above.
The full S-Series documentation set is available on the Technical Documentation CD-ROM and from the
Documentation tab of iSupport at the Force10 Networks website:
This document contains the following sections:
•
Accessing the Console Port on page 2
•
Setting Up Passwords on page 3
•
Setting Up Layer 2 Switching on page 4
•
Managing the Buffer Profile and Setting up Flow Control on page 5