Dell PowerStore 3000X EMC PowerStore Network Configuration Guide for PowerSwit - Page 48

PowerStore X model: Con switches, Establish a terminal session to the switch

Get Dell PowerStore 3000X PDF manuals and user guides View all Dell PowerStore 3000X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

7 PowerStore X model: Configure switches This chapter includes the following information. Topics: • Establish a terminal session to the switch • Validate the Top-of-Rack (ToR) switch versions and licensing • Configure general settings on the Top-of-Rack (ToR) switches • Configure PowerStore X model network VLANs on the switch • Configure Virtual Link Trunking interface • Configure the uplink ports on the Top of the Rack (ToR) switches Establish a terminal session to the switch Perform the following steps to establish a terminal session to the serial console port on the Dell EMC PowerSwitch Series. Prerequisites These steps are specific to establishing connections to Dell EMC PowerSwitch S4148-ON switches. For console serial port cable requirements, and further details refer to the Dell EMC PowerSwitch S4100-ON Series Installation Guide located at: https://www.dell.com/support/home/us/en/04/product-support/product/networking-s4148f-on/docs. About this task You must establish a terminal session to each of the switches to configure the switches for deployment. Steps 1. Power on the switch. 2. Use a serial cable to connect a computer to the serial console port, which is the top port located on the PSU-side of the PowerSwitch. For PSU-side of the switch layout see the Dell EMC PowerSwitch S4148-ON section of this guide. 3. Open a terminal emulator program, such as PuTTY, on the computer. 4. Configure the serial connection in the terminal emulator program using the following settings. Table 16. Serial connection settings Setting Speed(baud) Value 115200 (9600 for micro-USB port) Data bits 8 Stop bits 1 Parity None Flow control None 5. Connect to the switch using the terminal emulator program. 6. Enter the switch log in credentials. Default username and password are: ● Username: admin ● Password: admin 48 PowerStore X model: Configure switches

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
PowerStore X model: Configure switches
This chapter includes the following information.
Topics:
•
Establish a terminal session to the switch
•
Validate the Top-of-Rack (ToR) switch versions and licensing
•
Configure general settings on the Top-of-Rack (ToR) switches
•
Configure PowerStore X model network VLANs on the switch
•
Configure Virtual Link Trunking interface
•
Configure the uplink ports on the Top of the Rack (ToR) switches
Establish a terminal session to the switch
Perform the following steps to establish a terminal session to the serial console port on the Dell EMC PowerSwitch Series.
Prerequisites
These steps are specific to establishing connections to Dell EMC PowerSwitch S4148-ON switches.
For console serial port cable requirements, and further details refer to the
Dell EMC PowerSwitch S4100-ON Series Installation
Guide
located at:
.
About this task
You must establish a terminal session to each of the switches to configure the switches for deployment.
Steps
1.
Power on the switch.
2.
Use a serial cable to connect a computer to the serial console port, which is the top port located on the PSU-side of the
PowerSwitch.
For PSU-side of the switch layout see the
Dell EMC PowerSwitch S4148-ON
section of this guide.
3.
Open a terminal emulator program, such as PuTTY, on the computer.
4.
Configure the serial connection in the terminal emulator program using the following settings.
Table 16. Serial connection settings
Setting
Value
Speed(baud)
115200 (9600 for micro-USB port)
Data bits
8
Stop bits
1
Parity
None
Flow control
None
5.
Connect to the switch using the terminal emulator program.
6.
Enter the switch log in credentials. Default username and password are:
●
Username:
admin
●
Password:
admin
7
48
PowerStore X model: Configure switches