Denon DN-HC5000 Operating Instructions - Page 18

ENGLISH 5. Comparison of button operation W0 Q8 Q7 Q5 Q3 Q9 Q6 Q4 Q2 Q1 Q1 Q0 qe t ye u wr DN-D4500 Function q A1 q A2 q FLIP/B TRIM wB w EXIT/RELOOP e TRACK SELECT(±1) TRACK SELECT(±10) r CUE t SHUTTLE ring y PLAY/PAUSE u JOG wheel i-MP3 SEARCH MODE o PITCH SLIDER Q0 RELAY Q1 •MEMO -PRESET Q2 Enter Q3 PITCH BEND+/- Q4 OPEN/CLOSE Q5 •PITCH/KEY -RANGE Q6 - Q7 BRAKE Q8 - Q9 •TIME -TOTAL W0 TITLE •CONT./SINGLE A1 A2 FLIP DN-D4000 Function B EXIT/RELOOP TRACK SELECT(±1) TRACK SELECT(±10) CUE SHUTTLE ring PLAY/PAUSE JOG wheel JOG MODE PITCH SLIDER •MEMO -PRESET Enter PITCH BEND+/- OPEN/CLOSE •PITCH -RANGE -FOLDER -BRAKE REPEAT •TIME -TOTAL •TITLE •CONT./SINGLE io DN-HC5000 Button Name Oparation IN1 Press IN2 Press IN3 Press OUT1 OUT2 Press OUT3 Press 8 9 Press SHIFT + Press CUE Press 6 7 Press PLAY/PAUSE Press JOG disc Rotate JOG MODE Press Long Press PITCH SLIDER Move RELAY Press LOAD TO A Press LOAD TO B Long Press x2 Press PITCH BEND +/- Press AUTO LOOP Press KEY ADJ Press Long Press x1/2 Long Press CENSOR Press AUTO TEMPO Press •TIME Press Long Press •TITLE Press -CONT./SINGLE Long Press 5 PRESET • This function is only valid when the "PC" source is selected. (When the DN-D4000/D4500/BU4500 is connected, the corresponding preset operation is performed.) • The DN-HC5000 is equipped with a preset function allowing users to store and recall the devices' operation modes. The function includes the items and values described below. 1. Preset mode q Press and hold in the PRESET button for at least 1 second to enter the preset mode. w Use the PARAMETERS knob to select the preset item. e Select the item and press the PARAMETERS knob to set the preset item to be changed. r Next, turn the PARAMETERS knob. The preset data is selected. t Select the data and press the PARAMETERS knob to set the preset data to be changed. y To make multiple presettings, repeat steps w ~ t. u The preset mode is turned off when the PRESET button is pressed. 2. Preset items and data The "*" mark next to the data indicates the default value. (1) USB Mode Sel: HC5000 ITCH* Selects the USB communications mode. (2) CD Model Sel: DN-D4500* / DN-D4000 Select the name of the model to be connected to the DRIVE terminal and controlled. The BU4500 is the same as the DN-D4500's drive, so the PRESET setting is "DN-D4500". (3) Audio Fs Sel: 44.1k* / 48k / Auto 44.1 kHz: The sampling frequency (Fs) is fixed at 44.1 kHz, regardless of the data sent from the PC. 48 kHz: The sampling frequency (Fs) is fixed at 48 kHz, regardless of the data sent from the PC. AUTO: The sampling frequency (Fs) switches automatically according to the data sent from the PC. q To set "Fs", press PARAMETERS. "OK to CHANGE?" is displayed on the character display. w Press the PARAMETERS knob again. e After the sampling frequency is changed, "Audio Fs Sel" is displayed. (4) Unit No. Set: 1 to 15 / ALL* Sets the device's unit number. For example, when two devices are connected to a PC, set one device to "No. 2" or the like. (5) CH Set: 1&2* / 3&4 / 5&6 Sets the channel. (6) JOG Trns Int: 1ms to 20ms (3ms*) Selects JOG Pulse counts transfer interval. *For Vista users, please change this setting to 10 ms or higher. (7) JOG Pulse Sel: 1480* / 740 / 555 / 370 count/cycle Selects the number of pulses output per one revolution of the jog wheel. (8) FaderIn Mode: 1-PLAY/CUE / 2-PLAY/CUE* (9) X-CONT XFD: OFF* / ON Sets whether to enable or disable X-control input signal cross fader input. 14 ENGLISH