Dewalt D55154 Instruction Manual - Page 23

Possible Cause, Possible Solution, Cut-in

Get Dewalt D55154 PDF manuals and user guides View all Dewalt D55154 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

English Code possible cause 23 Paint spray on internal motor parts 24 Fuse blown, circuit breaker tripped 25 Tank pressure exceeds pressure switch cut-in pressure 26 Pressure release valve on pressure switch has not unloaded head pressure POSSIBLE SOLUTION Contact a DeWALT factory service center or a DeWALT authorized service center. Do not operate the compressor in the paint spray area. See flammable vapor warning. 1. Check fuse box for blown fuse and replace as necessary. Reset circuit breaker. Do not use a fuse or circuit breaker with higher rating than that specified for your particular branch circuit. 2. Check for proper fuse. Use only a time delay fuse. 3. Check for low voltage conditions and/or proper extension cord. 4. Disconnect the other electrical appliances from circuit or operate the compressor on its own branch circuit. Motor will start automatically when tank pressure drops below cut-in pressure of pressure switch. Set the On/Off switch to OFF. If the valve does not open, replace switch. Contact a DeWALT factory service center or a DeWALT authorized service center. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
±²
English
CODE
POSSIBLE CAUSE
POSSIBLE SOLUTION
±²
Paint spray on internal motor parts
Contact a D
E
WALT factory service center or a D
E
WALT
authorized service center. Do not operate the compressor in
the paint spray area. See flammable vapor warning.
±4
Fuse blown, circuit breaker tripped
1. Check fuse box for blown fuse and replace as necessary.
Reset circuit breaker. Do not use a fuse or circuit breaker
with higher rating than that specified for your particular
branch circuit.
±. Check for proper fuse. Use only a time delay fuse.
². Check for low voltage conditions and/or proper extension
cord.
4. Disconnect the other electrical appliances from circuit or
operate the compressor on its own branch circuit.
±5
Tank pressure exceeds pressure switch
cut-in
pressure
Motor will start automatically when tank pressure drops
below
cut-in
pressure of pressure switch.
±6
Pressure release valve on pressure switch has not
unloaded head pressure
Set the On/Off switch to OFF. If the valve does not open,
replace switch.
Contact a D
E
WALT factory service center or
a D
E
WALT authorized service center.