Dewalt DW713 Instruction Manual - Page 6
Specifications, Optional Accessories, ACCESSORIES - laser
View all Dewalt DW713 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
English Press down lightly on the operating handle and pull out the lock down pin, as shown in Figure 4. Gently release the downward pressure and allow the arm to rise to its full height. Use the lock down pin when carrying the saw from one place to another. Always use the carrying handle to transport the saw or the hand indentations shown in Figure 3. Specifications CAPACITY OF CUT 50° miter left and right 48° bevel left: 3° right 0° miter Max. Height 3.5" (89 mm) Max. Width 6.1" (155 mm) 45° miter Max. Height 3.5" (89 mm) Max. Width 4.2" (107 mm) 45° bevel Max. Height 2.3" (58 mm) Max. Width 6.1" (155 mm) 31.62° miter and 33.85° bevel Max. Width 5.25" (133 mm) Result Width 3.5" (89 mm) Result Height 1.25" (32 mm) Result Width 2.4" (61 mm) Result Height 1.25" (32 mm) Result Width 3.5" (89 mm) Result Height .75" (19 mm) Result Height .9" (23 mm) DRIVE 120 Volt Motor 2200 Watts 5000 RPM Carbide Tooth Blade 15 Amp Motor Cut Helical Gears with Roller and Ball Bearings Automatic Electric Brake Optional Accessories The following accessories, designed for your saw, may be helpful. In some cases, other locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in selecting and using accessories. Extension, Work Support: DW7080 Used to support long overhanging workpieces, the work support is user assembled. Your saw table is designed to accept two work supports; one on each side. Adjustable Length Stop: DW7051 Requires the use of one work support (see drawing). It is used to make repetitive cuts of the same length from 0 to 42" (107 cm). Clamp: DW7082 Used for firmly clamping workpiece to the saw fence for precision cutting. Dust Bag: DW7053 (Included with some models) Equipped with a zipper for easy emptying, the dust bag will capture the majority of the sawdust produced (not shown). Crown Molding Fence: DW7084 Used for precision cutting of crown molding. Laser Guide System: DW7187 Powered by the saw, the bright laser line delivers enhanced visibility in low and high light locations. Easy to install. Miter Saw LED Worklight System: DWS7085 Lighting used for greater visibility and cutting alignment during operation. Easy to install. Miter Saw Replacement Kerf Plate: DW7055 This durable plastic uncut plate limits blade tear out. DW7080 LOCKNUTS DW7082 END PLATE DW7187 DWS7085 DW7084 SAW BLADES: ALWAYS USE 10" (254 mm) SAW BLADES WITH 5/8" (16 mm) ARBOR HOLES. SPEED RATING MUST BE AT LEAST 5500 RPM. Never use a smaller diameter blade. It will not be guarded properly. Use crosscut blades only! Do not use blades designed for ripping, combination blades or blades with hook angles in excess of 7˚. BLADE DESCRIPTIONS APPLICATION DIAMETER TEETH Construction Saw Blades (thin kerf with anti-stick rim) General Purpose 10" (254 mm) 40 Fine Crosscuts 10" (254 mm) 60 Woodworking Saw Blades (provide smooth, clean cuts) Fine crosscuts 10" (254 mm) 80 Non-ferrous metals 10" (254 mm) 80 NOTE: For cutting non-ferrous metals, use only saw blades with TCG teeth designed for this purpose. ACCESSORIES WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product. 4