Edimax PRI-582 Available from Edimax USA User Manual - Page 95

Multi-nat

Get Edimax PRI-582 Available from Edimax USA PDF manuals and user guides View all Edimax PRI-582 Available from Edimax USA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

5.11.4 Multi-NAT Multi-NAT function allow you to configure multiple LAN IP Domain to each WAN port( total 10 LAN IP can be defined), after configure multiple NAT function It will act like have virtual router connect to Broadband Router LAN port, all traffic between each LAN IP domain , will send and receive through broadband router. it will provide following benefit . .* restrict broadcast storm in single IP domain. .* Broadband router can check each packet with DoS function enable. LAN IP: separated LAN IP domain. Subnet Mask: mask for IP domain. WAN IP: specific WAN IP address that match to LAN IP domain. You can leave blank in this field for PPPoE connection/ Or write down specific WAN IP address, if WAN port had Define multiple IP address on it (DMZ used) Blank: router will send packet follow by WAN filed selected . WAN: WAN1, WAN2, AUTO WAN1/2/3/4 ...router will route packet to correspond LAN/WAN AUTO..........router will route packet follow by "load balance" Function selected MULTI-NAT  95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
95
5.11.4 Multi-NAT
Multi-NAT function allow you to configure multiple LAN IP
Domain to each WAN port( total 10 LAN IP can be defined), after configure multiple
NAT function It will act like have virtual router connect to Broadband Router LAN
port, all traffic between each LAN IP domain , will send and receive through
broadband router. it will provide following benefit .
.
*
restrict broadcast storm in single IP domain.
.
*
Broadband router can check each packet with DoS function enable.
LAN IP:
separated LAN IP domain.
Subnet Mask:
mask for IP domain.
WAN IP:
specific WAN IP address that match to LAN IP domain.
You can leave
blank
in this field for PPPoE connection/
Or write down specific WAN IP address, if WAN port had
Define multiple IP address on it (DMZ used)
Blank: router will send packet follow by WAN filed selected .
WAN:
WAN1, WAN2, AUTO
WAN1/2/3/4 …router will route packet to correspond LAN/WAN
AUTO……….router will route packet follow by “load balance”
Function selected
MULTI-NAT