Electrolux EWFLW65HIW Use and Care Guide - Page 29

Setting Preferences, con't

Get Electrolux EWFLW65HIW - 27inch Front-Load Washer PDF manuals and user guides
UPC - 012505378652
View all Electrolux EWFLW65HIW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Operating User Interface Features 29 Setting Preferences, con't INSTALL CYCLE Run the INSTALL CYCLE before operating the washer the first time. Remove all items from the washer drum and press start. For more information on performing the washer INSTALL CYCLE, refer to the Installation Instructions accompanying this washer. If the washer has been installed according to Installation Instructions, INSTALL PASSED DOOR CAN BE OPENED will be displayed and the washer is ready to use. If the washer was not installed properly, NO WATER OPEN WATER VALVES, WATER HOSES - CHECK WATER HOSES or CALL SERVICE 877 435 3287 will be displayed to indicate the installation error. The errors may result from the following conditions: • NO WATER -Water inlet hoses have not been attached to water supply or water supply valves have not been turned on. Install hoses correctly and turn on water supply valves. • CHECK HOSES -The hot inlet hose may have been connected to the cold water supply and the cold inlet hose may have been connected to the hot water supply. Check hoses for correct supply connection. If incorrect, disconnect hoses and connect to correct inlets according to Installation Instructions. • CALL SERVICE 877 435 3287-Error can only be corrected by calling a qualified technician (1-877-435-3287). Repeat the INSTALL CYCLE when corrections are completed. NOTE The INSTALL CYCLE is prompted automatically only once when the washer is turned on the first time at the end of installation. After that, if you wish to run a subsequent INSTALL CYCLE when moving the washer or modifying your installation, you may perform your own INSTALL CYCLE by selecting it in the set prefs feature and then following the screen prompts.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
29
Operating User Interface Features
Setting Preferences, con’t
INSTALL CYCLE
Run the
INSTALL CYCLE
before operating the
washer the first time. Remove all items from the
washer drum and press
start
. For more informa-
tion on performing the washer
INSTALL CYCLE
,
refer to the
Installation Instructions
accompanying
this washer.
If the washer has been installed according to
Installation Instructions
,
INSTALL PASSED -
DOOR CAN BE OPENED
will be displayed and
the washer is ready to use.
If the washer was not installed properly,
NO WATER -
OPEN WATER VALVES
,
WATER HOSES - CHECK
WATER HOSES
or
CALL SERVICE 877 435
3287
will be displayed to indicate the installation
error.
The errors may result from the following condi-
tions:
NO WATER
•
—Water inlet hoses have not been
attached to water supply or water supply valves
have not been turned on. Install hoses correctly
and turn on water supply valves.
CHECK HOSES
•
—The hot inlet hose may have
been connected to the cold water supply and
the cold inlet hose may have been connected
to the hot water supply. Check hoses for cor-
rect supply connection. If incorrect, disconnect
hoses and connect to correct inlets according to
Installation Instructions
.
CALL SERVICE 877 435 3287
•
—Error can
only be corrected by calling a qualified techni-
cian (1-877-435-3287).
Repeat the
INSTALL CYCLE
when corrections are
completed.
NOTE
The INSTALL CYCLE is prompted automatically
only once when the washer is turned on the first
time at the end of installation. After that, if you
wish to run a subsequent
INSTALL CYCLE
when
moving the washer or modifying your installation,
you may perform your own
INSTALL CYCLE
by selecting it in the
set prefs
feature and then
following the screen prompts.