Epson 570e Product Information Guide - Page 15
Your Printer’s Default Settings, Changing Default Settings, Bidirectional Alignment - lq driver
UPC - 010343813854
View all Epson 570e manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
EPSON LQ-570e 6. Replace the paper guide, if necessary, and replace the printer cover. Then close the paper guide cover. 7. Turn on the printer. Make sure the Paper Out and Pause lights are off. Your Printers Default Settings While you can often set the default settings through your application software or printer driver, you may need to change a default setting from the printer's control panel using the default setting mode. The table below lists the default settings (in bold) and options you can select in this mode. Changing Default Settings Follow the steps below to enter the default setting mode and change the printer's default settings. To print the language selection and default setting mode instructions, you need 5 sheets of letter- or A4-size single-sheet paper or 5 pages of continuous paper. If you use single sheets, you need to load a new sheet each time the printer ejects a printed sheet. 1. Make sure paper is loaded and the printer is turned off. Whenever you turn off the printer, wait at least 5 seconds before turning it back on; otherwise you may damage the printer. Settings Page length for tractor Skip over perforation Options Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, 8.5, 11, 70/6, 12, 14, 17 On, Off 2. While holding down the Font button, turn on the printer. The printer enters the default-setting mode and prints the language selection instructions. Auto tear-off Auto line feed Print direction On, Off On, Off Bi-D, Uni-D, Auto 3. If you need to select a different language, press the Font button until the Font lights indicate the language you want, as described in the language selection instructions. Software 0 slash ESC/P2, IBM 2390 Plus 0, 0 4. Press the Tear Off/Bin button to confirm your language selection and print the current default settings. High speed draft I/F mode Auto I/F wait time Parallel I/F bidirectional mode Packet mode Auto CR (IBM 2390 Plus)* A.G.M. (IBM 2390 Plus)* Character table* On, Off Auto, Parallel, Optional 10 seconds, 30 seconds On, Off Auto, Off On, Off On, Off Standard model: Italic, PC 437, PC 850, PC 860, PC 863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15, All other models: Italic, PC 437, PC 850, PC 437 Greek, PC 853, PC 855, PC 852, PC 857, PC 864, PC 866, PC 869, MAZOWIA, Code MJK, ISO 8859-7, ISO Latin 1T, Bulgaria, PC 774, Estonia, ISO 8859-2, PC 866 LAT, PC 866 UKR, PC APTEC, PC 708, PC 720, PC AR864, PC 860, PC863, PC 865, PC 861, BRASCII, Abicomp, Roman 8, ISO Latin 1, PC 858, ISO 8859-15, PC 771 5. If you do not need to change any settings, go to step 6. If you want to change any of the default settings, press the Tear Off/Bin button to print the instructions (three pages) in the language you selected. Follow these instructions to change the default settings using the buttons on the printer's control panel. The arrows on the instruction sheets indicate the printers current settings. 6. When you finish, turn off the printer and exit the default setting mode. The current settings remain in effect until you change them again. Bidirectional Alignment If you notice that the vertical lines in your printout are not properly aligned, you can use the printer's bidirectional adjustment mode to correct this problem. International character set for Italic table Font Italic U.S.A., Italic France, Italic Germany, Italic U.K., Italic Denmark1, Italic Sweden, Italic Italy, Italic Spain1 OCR-B, Orator, Orator-S, Script C, Roman T, Sans Serif H To complete the steps below, you need 5 single sheets or 5 pages of continuous paper. If you use single sheets, you need to load a new sheet of paper each time the printer ejects a printed sheet onto the paper guide. Manual feed wait time 1 second, 1.5 seconds, 2 seconds, 3 seconds 1. Make sure paper is loaded and the printer is turned off. Buzzer Roll paper On, Off On, Off * These settings take effect only when IBM 2390 Plus emulation is selected. Whenever you turn off the printer, wait at least 5 seconds before turning it back on; otherwise you may damage the printer. 4/00 EPSON LQ-570e - 15