Epson Stylus Pro 7600 - UltraChrome Ink Quick Reference Guide
Epson Stylus Pro 7600 - UltraChrome Ink - Stylus Pro 7600 Print Engine Manual
View all Epson Stylus Pro 7600 - UltraChrome Ink manuals
Add to My Manuals
Save this manual to your list of manuals |
Epson Stylus Pro 7600 - UltraChrome Ink manual content summary:
- Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 1
EPSON Stylus® Pro 7600/9600 Quick Reference Guide - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 2
3-inch roll paper core, attach the gray adapters to the paper stops at each end. See your Printer Guide for details. 2 Position the roll paper as shown, then slide it onto the spindle. 3 Slide button. The paper feeds into the printing position automatically and READY appears on the control panel. 1 - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 3
appears on the control panel. To avoid damaging the printer, never move the paper lever during printing, or while the Operate or Pause light is flashing. 7 Print your page. After it is finished, the sheet stays in the printer. 8 To remove your print, press the Paper Feed button. 4 Feed the sheet - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 4
cover. (The cover has special tabs that act as paper supports when the cover is open.) 7 Return the paper lever board feeds into the printing position automatically and READY appears on the control panel. 9 Run your print job. After it is finished, the posterboard stays in the printer. 6 Align the - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 5
running a cleaning cycle, you may need to align the print head as described in the Printer Guide. Banding can also be caused by selecting the incorrect paper type in your printer software. Be sure to select the paper you're using in the EPSON printer software or in a third-party RIP. If your paper - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 6
. Make sure you have the correct replacement cartridge. If you have a Stylus Pro 9600 that uses EPSON UltraChrome ink, you can install any combination of 110 ml and 220 ml cartridges. Unless you are planning to switch between black print modes (see your Printer Guide for details), be sure to replace - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 7
open. If you see the message WRONG INK CARTRIDGE, you may have loaded an incorrect black ink cartridge for the black ink mode you're currently in, or a cartridge containing the wrong type of ink for your printer (Photographic Dye or UltraChrome). Remove any cartridges indicated by a red light on the - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 8
on the control panel, then press until you see PRINTER STATUS. 2 Press , then press until you see SERVICE LIFE. 3 Press , then press until you see CUTTER Maintenance Tank The maintenance tank stores ink that gets flushed from the system during print head cleaning and other maintenance procedures. - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 9
Printer Guide. Message Light Explanation Response INK LOW Ink Out light(s) flashing Ink cartridge(s) nearly Replace ink cartridge(s) indicated empty (printing continues). by Ink Out light(s). See page 7. INK OUT Ink Out light(s) on Ink cartridge(s) empty (printing stops). Replace ink - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 10
Go to http: //support.epson.com to download drivers, access product documentation and troubleshooting, and get technical advice through e-mail. Contact the RIP manufacturer. EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON UltraChrome and EPSON Photographic Dye are - Epson Stylus Pro 7600 - UltraChrome Ink | Quick Reference Guide - Page 11
EPSON
Stylus
®
Pro 7600/9600
Quick Reference Guide