Fisher and Paykel RF201ADUSX5 User Guide - Page 13

Locate desired position for water filter noting

Get Fisher and Paykel RF201ADUSX5 PDF manuals and user guides View all Fisher and Paykel RF201ADUSX5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Installation instructions 11 US CA Installation instructions: 1 Ensure the refrigerator is NOT plugged into a power supply. 2 Locate a cold water supply/feed only suitable for a water connection. Tee and tap fitting is not supplied. 3 Connect the 8" (200 mm) blue tubing to the outlet of the PRV (blue collet) and the inlet connection of the water filter cartridge as shown in Diagram 1. Gently pull on both ends to ensure it is locked. 4 Connect the white ¼" (6 mm) tubing to the outlet of the water filter cartridge as shown in Diagram 2. Gently pull to ensure it is locked. 5 Measure the required length of tubing to run from the PRV to the water connection point (no less than 10" (250 mm)). 6 Cut the tubing making sure the ends are square and clean. 7 Connect the tubing to the faucet connection and the base of the PRV (white collet) and then to the faucet as shown in Diagram 3. Please note that the faucet connection supplied should fit most installation situations. 8 Connect one locking key to each side of the water filter cartridge in between the cartridge and the locking collet as shown in Diagram 4. 9 To flush the water filter of any trapped air, harmless carbon fines and to also check for leaks, aim the end of the tubing into a bucket, turn isolating faucet on and run at least 10 qt (10 L) of water through. Once complete, turn isolating faucet off. 10 Locate desired position for water filter noting carefully the following points: ■■ It is recommended to fit the water filter in a vertical orientation with the water filter head at the top. This will minimize water leakage when replacing cartridge. ■■ Ensure the filter is in a convenient location to access every 6 months for replacement. We suggest that this location is beside the water filter supply faucet in a cupboard beside the refrigerator. ■■ A minimum clearance of 2 ½" (64 mm) from the bottom of the filter cartridge is required to perform cartridge removal. ■■ Do not screw water filter to refrigerator. INLET Diagram 1 Fig.3 PRV connection Diagram 2 Fig.4 Waterline connection to refrigerator Diagram 3 Fig.5 Faucet connection Diagram 4 Fig.6 Locking key

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
11
Installation instructions
Installation instructions:
1
Ensure the refrigerator is NOT plugged into a
power supply.
2
Locate a cold water supply½feed only suitable for a
water connection. Tee and tap fitting is not supplied.
3
Connect the 8” (200 mm) blue tubing to the outlet of
the PRV (blue collet) and the inlet connection of the
water filter cartridge as shown in Diagram 1. Gently
pull on both ends to ensure it is locked.
4
Connect the white ¼” (6 mm) tubing to the outlet
of the water filter cartridge as shown in Diagram 2.
Gently pull to ensure it is locked.
5
Measure the required length of tubing to run from
the PRV to the water connection point (no less than
10” (250 mm)).
6
Cut the tubing making sure the ends are square and
clean.
7
Connect the tubing to the faucet connection and
the base of the PRV (white collet) and then to the
faucet as shown in Diagram 3. Please note that
the faucet connection supplied should fit most
installation situations.
8
Connect one locking key to each side of the water
filter cartridge in between the cartridge and the
locking collet as shown in Diagram 4.
9
To flush the water filter of any trapped air, harmless
carbon fines and to also check for leaks, aim the end
of the tubing into a bucket, turn isolating faucet on
and run at least 10 qt (10 L) of water through. Once
complete, turn isolating faucet off.
10
Locate desired position for water filter noting
carefully the following points:
■
±
It is recommended to fit the water filter in a
vertical orientation with the water filter head at
the top. This will minimize water leakage when
replacing cartridge.
■
±
Ensure the filter is in a convenient location to
access every 6 months for replacement. We
suggest that this location is beside the water
filter supply faucet in a cupboard beside the
refrigerator.
■
±
A minimum clearance of 2 ¾” (64 mm) from
the bottom of the filter cartridge is required to
perform cartridge removal.
■
±
Do not screw water filter to refrigerator.
Diagram 2
Fig.4 Waterline connection
to refrigerator
INLET
Diagram 4
Fig.6 Locking key
Fig.3 PRV connection
Diagram 1
Diagram 3
Fig.5 Faucet connection
US
CA