Fisher and Paykel RF201ADUSX5 User Guide - Page 15

Important

Get Fisher and Paykel RF201ADUSX5 PDF manuals and user guides View all Fisher and Paykel RF201ADUSX5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installation instructions 13 US CA Important! ■■ All connections must be checked for leaks. ■■ Ensure white ¼" (6 mm) tubing is routed away from sharp objects, sharp corners (beware of kinking the tube as this will stop water flow), clear of the refrigerator rear compartment and not in a location where it can be kinked or squashed. ■■ Ensure all push-fit connections are firmly pushed into place. The tube should push in 5/8" (16 mm) before reaching the stop. ■■ If tubing is removed at any point, re-cut the end and re-insert. Tubing must be fully inserted to avoid leaks. ■■ To remove tube from connection points first turn off the isolating faucet. Gently push the 6 dispensing PART: 838587 7 pad a few times DRAWING: 838587 8 using a glas9 s or container to remove the static line pressure. Push in the collet firmly while pulling back on the tubing at the same time, as shown in Diagram 10. Diagram 10 Diagram 11 Fig.9 Connection to water supply System tested and certified by NSF International against NSF/ANSI Standard 53 for the reduction of Asbestos, Atrazine, Benzene, Cyst, Carbofuran, Lead, Lindane, Mercury, P-Dichlorobenzene, Toxaphene & Turbidity; against Standard NSF/ANSI 42 for the reduction of Chlorine Taste and Odor and Nominal Particulate Class I to a capacity of 750 gallons (2,838 liters).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
13
Installation instructions
Important!
■
±
All connections must be checked for leaks.
■
±
Ensure white ¼” (6 mm) tubing is routed away from sharp objects, sharp corners (beware of
kinking the tube as this will stop water flow), clear of the refrigerator rear compartment and not
in a location where it can be kinked or squashed.
■
±
Ensure all push-fit connections are firmly pushed into place. The tube should push in ±²³” (16 mm)
before reaching the stop.
■
±
If tubing is removed at any point, re-cut the end and re-insert. Tubing must be fully inserted to
avoid leaks.
■
±
To remove tube from connection points first turn off the isolating faucet. Gently push the
dispensing pad a few times using a glass or container to remove the static line pressure. Push in
the collet firmly while pulling back on the tubing at the same time, as shown in Diagram 10.
Diagram 11
Diagram 10
Fig.9 Connection to water supply
System tested and certified by NSF International against NSF½ANSI Standard 53 for the reduction
of Asbestos, Atrazine, Benzene, Cyst, Carbofuran, Lead, Lindane, Mercury, P-Dichlorobenzene,
Toxaphene & Turbidity; against Standard NSF½ANSI 42 for the reduction of Chlorine Taste and
Odor and Nominal Particulate Class I to a capacity of 750 gallons (2,838 liters).
US
CA