Foxconn G41MD-V English Manual - Page 25

CPU 533 Jumper: CPU_533

Get Foxconn G41MD-V PDF manuals and user guides View all Foxconn G41MD-V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

2 CAUTION USB device wake-up Jumper: USBPWR1 / USBPWR2 1. Set the jumper to pins 1-2 (+5V) to wake up the computer from S1 sleep mode using the connected USB devices. 2. Set the jumper to pins 2-3 (+5VSB) to wake up the computer from S3 and S4 sleep modes using the connected USB devices. At the same time, a corresponding setting must be set in BIOS as below: Set "CMOS Setup" -> "Power Management Setup" -> "USB Wake Up From S3" to "Enabled". 1 +5V 2 (Default) 3 1 +5VSB 2 3 USBPWR1/2 ! ■ USBPWR1 is for the internal USB connectors, USBPWR2 is for the rear USB ports. ■ The USB device wake-up feature requires a power supply that can provide 500mA on +5VSB lead for each USB port; otherwise, the system will not power up. ■ The total current consumed must not exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode. CPU 533 Jumper: CPU_533 When you use the CPU FSB is 533MHz, set the jumper to pins 1-2. Return the setting to its original with pins 2-3 closed. 1 Enabled 2 3 1 Disabled 2 (Default) 3 CPU_533 18 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
18
2
18
USB device wake-up Jumper: USBPWR1 / USBPWR2
1. Set the jumper to pins 1-2 (+5V) to wake up the computer from S1 sleep mode using the
connected USB devices.
2. Set the jumper to pins 2-3 (+5VSB) to wake up the computer from S3 and S4 sleep modes
using the connected USB devices. At the same time, a corresponding setting must be set in
BIOS as below:
Set “CMOS Setup” -> “Power Management Setup” -> “USB Wake Up From S3”
to “Enabled”.
USBPWR1/2
+5V
(Default)
1
2
3
+5VSB
1
2
3
■
USBPWR1 is for the internal USB connectors, USBPWR2 is for the rear USB ports.
■
The USB device wake-up feature requires a power supply that can provide 500mA
on +5VSB lead for each USB port; otherwise, the system will not power up.
■
The total current consumed must not exceed the power supply capability (+5VSB)
whether under normal condition or in sleep mode.
CAUTION
!
CPU 533 Jumper: CPU_533
When you use the CPU FSB is 533
MHz, set the jumper to pins 1-2. Return the setting to its
original with pins 2-3 closed.
CPU_533
Enabled
1
2
3
Disabled
(Default)
1
2
3