Fujitsu FI 4220C Operator Manual

Fujitsu FI 4220C - Document Scanner Manual

Get Fujitsu FI 4220C - Document Scanner PDF manuals and user guides View all Fujitsu FI 4220C manuals
Add to My Manuals
Save this manual to your list of manuals

Fujitsu FI 4220C manual content summary:

  • Fujitsu FI 4220C | Operator Manual - Page 1
    P3PC-E017-01EN fi-4220C Image Scanner Operator's Guide
  • Fujitsu FI 4220C | Operator Manual - Page 2
    Duplex Color Scanner. The fi-4220C scanner is capable of scanning color images on both sides, and has the following features. I Easy Scanning and Display The ADF (Automatic Document Feeder) allows you to scan A4-size duplex color documents at a high speed of 25 pages per minute. I Easily Installable
  • Fujitsu FI 4220C | Operator Manual - Page 3
    . 5 DAILY CARE This chapter describes how to clean the scanner. 6 REPLACING CONSUMABLES This chapter describes how to replace scanner consumables. 7 TROUBLESHOOTING This chapter describes how to remedy document jams, other trouble, items to check before contacting the agent where you bought the
  • Fujitsu FI 4220C | Operator Manual - Page 4
    chapter describes the required document size and paper quality for ensuring correct operation of the ADF. 9 SCANNER SPECIFICATION This chapter lists the scanner specifications. We hope that this manual is useful in taking full advantage of the fi-4220C Duplex Color Scanner's advantages. April, 2002
  • Fujitsu FI 4220C | Operator Manual - Page 5
    to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
  • Fujitsu FI 4220C | Operator Manual - Page 6
    WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTICE • The use of a non-shielded interface cable with the referenced device is prohibited. The length of the parallel interface
  • Fujitsu FI 4220C | Operator Manual - Page 7
    Bescheimigung des Herstellers / Importeurs Hiermit wird bescheinigt, daß der/dieldas • fi-4220C in Übereinsstimmung mit den Bestimmungen der • AmtsblVfg 243/1991 funkentstört ist. Der Deutschen Bundesport wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung
  • Fujitsu FI 4220C | Operator Manual - Page 8
    required, for example, in the control of nuclear reactions at nuclear power facilities, automatic flight control of aircraft, air traffic control, operation and when provisionally the safety in question is not ensured. The user should use this product without adopting measures for ensuring safety in
  • Fujitsu FI 4220C | Operator Manual - Page 9
    in scanner parts. Dispose of the scanner should be conducted as required by local ordinances or regulations. Illegal Copying Copying of bank notes, currency, government-issued bonds and passports, licenses and permits issued by public and private organizations, official documents, private documents
  • Fujitsu FI 4220C | Operator Manual - Page 10
    Edition operating system. Windows® 2000: Refers to Microsoft® Windows® 2000 Professional operating system. Windows® XP: Refers to Microsoft® Windows® XP Professional operating system, and Microsoft® Windows® XP Home Edition operating system Windows NT®: Refers to Microsoft® Windows NT® operating
  • Fujitsu FI 4220C | Operator Manual - Page 11
    you start to use this product. In particular, be sure to read and fully understand the Safety Precautions described in this manual before you use this product. Also, store this manual in a safe place so that it can be easily referred to during use of this product. Warning Indications Used In This
  • Fujitsu FI 4220C | Operator Manual - Page 12
    Symbols Used In This Manual This manual uses the following symbols in explanations in addition to which users are not allowed to do.The drawing inside or under the circle shows the specific action that is not allowed. Outline characters on a colored background shows instructions users should follow
  • Fujitsu FI 4220C | Operator Manual - Page 13
    manual, operate by following the actual displayed screen referring to the User's Manual of the scanner application you are using. Furthermore, the screenshots in this manual are for the FUJITSU TWAIN32 scanner driver and the Image Capturing Software Utilities "ScandAll 21" for Microsoft® Windows
  • Fujitsu FI 4220C | Operator Manual - Page 14
    in this manual. Do not damage the AC cable. A damaged AC cable might cause fire or electric shock. Do not place heavy objects on AC cables, or pull, bend, twist, heat, damage or modify AC cables. Also, do not use damaged AC cables or power plugs, and AC cables or power plugs when
  • Fujitsu FI 4220C | Operator Manual - Page 15
    plug. Wipe off any dust from metal parts on the power plug or metal fittings with a soft, dry cloth. Accumulated dust might cause fire or electric shock. Do not install in locations subject to oil smoke, steam, humidity, and dust. Do not install the scanner in locations subject to oil smoke, steam
  • Fujitsu FI 4220C | Operator Manual - Page 16
    sense heat coming from devices or detect other malfunctions such as smoke, strange smells or strange noises, immediately press down the power button to turn off the scanner and then disconnect its power plug. Make sure that the smoke has disappeared, and then contact the agent where you bought the
  • Fujitsu FI 4220C | Operator Manual - Page 17
    metal objects, liquids, etc.) get inside the scanner, immediately press down the power button to turn off the scanner and disconnect the power plug from the power outlet. Then contact the agent where you bought the scanner or Maintenance Service Center. Pay particular attention to this warning in
  • Fujitsu FI 4220C | Operator Manual - Page 18
    Do not touch the inside of the scanner unless necessary. Do not disassemble or modify the scanner. The inside of the scanner contains high-voltage components. Touching these components might cause fire or electric shock. xvii
  • Fujitsu FI 4220C | Operator Manual - Page 19
    cautions described in this manual. Do not touch the AC cable with wet hands. Do not insert or disconnect the power plug with wet hands. Doing so might cause electric shock. Do not install the scanner on unstable surfaces. Install the scanner on a desk so that none of its parts protrude outside of
  • Fujitsu FI 4220C | Operator Manual - Page 20
    Do not place heavy objects on the scanner or use the scanner's top surface for performing other work. Improper installation might cause injuries. Before moving the scanner, disconnect the power plug from the power outlet. Do not move the scanner with the power and interface cables connected as this
  • Fujitsu FI 4220C | Operator Manual - Page 21
    Protect the scanner from static electricity. Install the scanner away from strong magnetic fields and other sources of noise. Also, protect the scanner from static electricity as this might cause the scanner to malfunction. Do not use aerosol sprays near the scanner. Do not use aerosol sprays, for
  • Fujitsu FI 4220C | Operator Manual - Page 22
    power outlet. Leaving the scanner turned ON might result in damage to the scanner. Do not install the scanner in the direct sunlight. Do not install the scanner in the direct sunlight or near heating apparatus. Doing so might cause heat to build up inside the scanner, causing fire or scanner trouble
  • Fujitsu FI 4220C | Operator Manual - Page 23
    send your comments on this manual or on Fujitsu products to the following addresses: FUJITSU COMPUTER PRODUCTS OF AMERICA, INC 5457 Website: http://www.fujitsu.ca/ E-mail: [email protected] (For Sales Questions) [email protected] (For technical questions) FUJITSU DEUTSCHLAND GMBH. Frankfurter
  • Fujitsu FI 4220C | Operator Manual - Page 24
    www.fujitsu-europe.com/ FUJITSU AUSTRALIA LTD. Fujitsu House -2277 Website: http://fw.fujitsu.com/ FUJITSU ICL ESPAÑA, S.A. Camino Cerro http://www.fujitsu-europe.com/ E-mail: [email protected] FUJITSU ASIA PTE http://sg.fujitsu.com/ E-mail: [email protected] FUJITSU HONG KONG
  • Fujitsu FI 4220C | Operator Manual - Page 25
    Group 658-1 Tsuruma Machida-shi, Tokyo 194-8510, Japan Phone: (81-42)796-5211 Fax: (81-42)788-7651 Website: http://www.pfu.fujitsu.com/ E-mail: [email protected] Corporate headquarters Nu 98-2 Unoke, Unoke-machi, kahoku-gun, Ishikawa 929-1192, Japan Phone: (81-76)283-1212 Fax: (81-76)283
  • Fujitsu FI 4220C | Operator Manual - Page 26
    OF A SCANNER.......17 2.1 Installing the Scanner 18 2.2 Connecting the Scanner to a PC 22 2.3 Installing the Scanner Application 29 3 BASIC SCANNER OPERATIONS.......31 3.1 Turning the Scanner ON 32 3.2 Loading Documents on the ADF for Scanning ........ 34 3.3 Loading Documents on the Flatbed for
  • Fujitsu FI 4220C | Operator Manual - Page 27
    Replacing the Pick Roller 92 7 TROUBLESHOOTING 103 7.1 Removing Jammed Documents 104 7.2 Remedying Typical Troubles 107 7.3 Items to check before contacting the agent where you bought the scanner 126 7.4 Checking Labels on the Scanner 130 8 ADF AND PAPER SPECIFICATION .133 8.1 Document Size
  • Fujitsu FI 4220C | Operator Manual - Page 28
    GLOSSARY OF TERMS GL-1 INDEX IN-1 xxvii
  • Fujitsu FI 4220C | Operator Manual - Page 29
    xxvii
  • Fujitsu FI 4220C | Operator Manual - Page 30
    PREPARING THE SCANNER 1 PREPARING THE SCANNER 1 This chapter describes how to prepare the scanner for use. 1.1 Checking the Contents of the Scanner Package ....... 2 1.2 Names and Functions of Parts 4 1.3 Operator panel 11 1
  • Fujitsu FI 4220C | Operator Manual - Page 31
    1.1 Checking the Contents of the Scanner Package When you unpack the scanner package, make sure that all the following parts are included in the package. If any parts are missing or defective, contact your sales representative. Handle the scanner and accessories with care. 2 1.1 Checking the
  • Fujitsu FI 4220C | Operator Manual - Page 32
    PREPARING THE SCANNER • Scanner Scanner and Accessories • ADF paper chute • AC adapter • AC cable 1 • USB interface cable • Scanner driver CD-ROM • Adobe® Acrobat® 5.0 CD-ROM • Manual CD-ROM • Operator's Guide • Quick Installation (this manual) Guide fi-XXXX XXXXXXXXX 1.1 Checking the
  • Fujitsu FI 4220C | Operator Manual - Page 33
    1.2 Names and Functions of Parts This section describes the names of parts and their functions. I Front (2) ADF paper chute (1) ADF(Automatic document feeder) (3) Side guide (7) Flatbed (4) ADF button (5) Operator panel (6) Stacker 4 1.2 Names and Functions of Parts
  • Fujitsu FI 4220C | Operator Manual - Page 34
    Name Function 1 ADF(Automatic Automatically feeds documents into document the scanner. feeder) 2 ADF paper chute 3 Side guide Used when scanning documents on the ADF. 1 Adjust the side guides to match the width of the document to avoid image skew. PREPARING THE SCANNER 4 ADF button Press
  • Fujitsu FI 4220C | Operator Manual - Page 35
    I Inside (11) Document cover (10) Document holding pad (9) Document bed (8) Shipping lock (located on bas) 6 1.2 Names and Functions of Parts
  • Fujitsu FI 4220C | Operator Manual - Page 36
    one sheet at a time. This is also called the 1 Flatbed. 10 Document holding Holds the document against the pad document bed. 11 Document cover When closed, this cover holds down the document loaded on the document bed in position. PREPARING THE SCANNER 1.2 Names and Functions of Parts 7
  • Fujitsu FI 4220C | Operator Manual - Page 37
    I Rear (12) SCSI ID switch (15) DC inlet (13) SCSI Interface connector (14) USB Interface connector 8 1.2 Names and Functions of Parts
  • Fujitsu FI 4220C | Operator Manual - Page 38
    12 SCSI ID switch 13 SCSI interface connector 14 USB interface connector 15 DC inlet Function Sets the SCSI ID. (Set to "5" before the scanner is shipped from the factory.) Connect the SCSI interface cable from the host PC or Computer 1 here. Connect the USB interface cable from the host
  • Fujitsu FI 4220C | Operator Manual - Page 39
    I Removable Parts The following shows the parts that can be removed from the scanner. Removal is possible. Pick roller ADF paper chute Pad ASY Document cover Sheet guide 10 1.2 Names and Functions of Parts
  • Fujitsu FI 4220C | Operator Manual - Page 40
    PREPARING THE SCANNER 1.3 Operator panel The operator panel is located on the right side of the scanner. This panel comprises a Function No. display, four buttons and a LED. 1 Function No. display Function Send to Scan Power button LED 1.3 Operator panel 11
  • Fujitsu FI 4220C | Operator Manual - Page 41
    the application software according to the details set in the launcher (*). Turns the scanner ON and OFF. Lights when the scanner is turned ON. *) For information on detailed settings for the launcher, refer to the Scanner Utility for Microsoft® Windows® User's Guide on the scanner driver CD-ROM
  • Fujitsu FI 4220C | Operator Manual - Page 42
    successfully. Also, this status is called "Ready Status". I U Indicates that a temporary error occurred while the document was being scanned. "U" and "0 to 2" are display alternately. To return the scanner to the ready status ("1"), press "Scan" or "Send to" button while the error is indicated
  • Fujitsu FI 4220C | Operator Manual - Page 43
    a device alarm occurred while the document was being scanned. "E" and the alarm No. (0 to 9, c and d) are indicated alternately. To return the scanner to the ready status ("1"), press "Scan" or "Send to" button while the alarm is indicated. If this alarm occurs, turn the power off and on again. If
  • Fujitsu FI 4220C | Operator Manual - Page 44
    If this error occurs, release the Shipping lock. See "2.1 Installing the Scanner" for the procedure to release the Shipping lock. • "U1" error If this error occurs, remove jammed document. See "7.1 Removing Jammed Documents" for removing jammed document. • "U2" error If this error occurs, remove the
  • Fujitsu FI 4220C | Operator Manual - Page 45
    (Flatbed). An trouble occurred on the optical system (front). An trouble occurred on the optical system (back). The motor fuse has blown. An trouble occurred on the operator panel. An trouble occurred in the EEPROM. The SCSI interface fuse has blown. An trouble occurred in image memory. An trouble
  • Fujitsu FI 4220C | Operator Manual - Page 46
    Professional operating system. Windows® XP Refers to Microsoft® Windows® XP Professional operating system. Refers to Microsoft® Windows® XP Home Edition operating system. Windows NT® Refers to Microsoft® Windows NT® operating system Version4.0. 2.1 Installing the Scanner 18 2.2 Connecting the
  • Fujitsu FI 4220C | Operator Manual - Page 47
    following shows the procedure for installing the scanner. 1. Place the scanner at its installation site. For details on the scanner's dimensions and required installation space, see "9.2 Installation Specifications." 2. Unlock the Shipping lock. The carrier unit inside the scanner is fixed in place
  • Fujitsu FI 4220C | Operator Manual - Page 48
    A SCANNER 3. Attach the ADF paper chute. For details on how to attach the ADF paper chute, see "I Attaching the ADF paper chute" in this section. 4. Connect the AC adapter. For details on how to connect the AC adapter, see "I Connecting the AC Adapter" in this section. 2 2.1 Installing the Scanner
  • Fujitsu FI 4220C | Operator Manual - Page 49
    chute The following shows the procedure for attaching the ADF paper chute. 1. Hold the ADF paper chute and insert its tabs into the counterpart holes on the scanner as shown in the figure below. The Side guide of the ADF paper chute has to face up. ADF paper chute tab Side guide 20 2.1 Installing
  • Fujitsu FI 4220C | Operator Manual - Page 50
    shows the procedure for connecting the AC adapter. Use only whth AC adapter provided by the CAUTION manufacturer. 1. Connect the AC cable to the AC adapter. 2 2. Connect the connector of AC adapter to the DC inlet of the scanner. 3. Insert the AC cable into the outlet. 2.1 Installing the Scanner 21
  • Fujitsu FI 4220C | Operator Manual - Page 51
    running Windows® 98, Windows® ME, Windows® 2000, or Windows® XP, connect either the USB interface cable or the SCSI interface cable. ATTENTION Connect only one of the USB or SCSI interface cables. Windows® 95 and Windows NT® 4.0 does not support USB interface. 22 2.2 Connecting the Scanner to
  • Fujitsu FI 4220C | Operator Manual - Page 52
    . 1. Connect the USB interface cable to the USB interface connector. 2 2. Connect the other end of the USB interface cable to the PC. 3. Press down the scanner power button on the Function No. display to turn on the
  • Fujitsu FI 4220C | Operator Manual - Page 53
    4. Press the power button on the face plate of the PC to turn on the PC. ATTENTION • Be sure to use the USB cable which comes as an accessory with this scanner. We does not confirm the correct operation of a commercial USB cable. • When connecting to a USB hub, use the first stage USB
  • Fujitsu FI 4220C | Operator Manual - Page 54
    noted on the following home page. 2 http://imagescanner.fujitsu.com/ ATTENTION • When connecting the SCSI interface cable, be sure to first connect the SCSI interface cable then turn on the power of the scanner and the personal computer. • Connect the scanner so that it is the terminal device on
  • Fujitsu FI 4220C | Operator Manual - Page 55
    the interface connector until both sides click. 2. Connect the connector on the other end of the cable to the personal computer. ATTENTION When using the scanner on the SCSI interface, connect the scanner so that it is the terminal device on the SCSI daisy chain. 26 2.2 Connecting the
  • Fujitsu FI 4220C | Operator Manual - Page 56
    other SCSI device. For details on how to change the SCSI ID, see "I Setting the SCSI ID" in this section. 3. Press down the scanner power button on the Function No. display to turn on the scanner. 2 4. Press the power button on the face plate of the PC to turn on the PC. ATTENTION This
  • Fujitsu FI 4220C | Operator Manual - Page 57
    ID switch on the back of the image scanner. 456 Click 23 78 901 ID No. 0 to7 8, 9 Description These address numbers can be set. The factory default value (SCSI ID = 5) is used for these numbers. 3. Press the power button to turn the scanner ON. When the scanner is turned ON, the SCSI ID set
  • Fujitsu FI 4220C | Operator Manual - Page 58
    scanner driver and Image Capturing Software Utilities "ScandAll 21" for Microsoft® 2 Windows® (ScandAll 21) , refer to the fi-4220C Quick Installation Guide. For further details on installing the FUJITSU TWAIN32 scanner driver, refer to the Scanner Utility for Microsoft® Windows® User's Guide
  • Fujitsu FI 4220C | Operator Manual - Page 59
    30 2.3 Installing the Scanner Application
  • Fujitsu FI 4220C | Operator Manual - Page 60
    using is other than Windows® XP. Also, when FUJITSU TWAIN32 is updated the screens and operations noted in this chapter will differ slightly. 3.1 Turning the Scanner ON 32 3.2 Loading Documents on the ADF for Scanning ........ 34 3.3 Loading Documents on the Flatbed for Scanning... 39 3.4 Scanning
  • Fujitsu FI 4220C | Operator Manual - Page 61
    ON. The following shows the procedure for turning the scanner ON. 1. Press the power button on the operator panel. The scanner is turned ON, and the green LED on the operator panel lights. Also, while the scanner is being initialized, the indication of the Function No. display changes as follows
  • Fujitsu FI 4220C | Operator Manual - Page 62
    mode, perform one of the following: • Load the document on the ADF paper chute. • Press any button on the operator panel. However, holding down the power button for will turn the scanner OFF. • Execute a command from the scanner driver. 3 BASIC SCANNER OPERATIONS 3.1 Turning the Scanner ON 33
  • Fujitsu FI 4220C | Operator Manual - Page 63
    Scanning The following shows the procedure for loading documents on the ADF paper chute. 1. Align the edges of the document. To do this, perform the following. 1) Align the front and side edges of the document to be loaded. Documents can be scanned more correctly if both edges are aligned. 2) Check
  • Fujitsu FI 4220C | Operator Manual - Page 64
    BASIC SCANNER OPERATIONS 2. Fan the document When loading a multiple-sheet document, fan the document as follows. 1) Take out a stack of document sheets with thickness of 5mm or less. 2) Lightly grip both ends of the document with both hands, and bend the document as follows. 5mm 3 3) Firmly
  • Fujitsu FI 4220C | Operator Manual - Page 65
    first page) contacts to the ADF paper chute. Furthermore, when you have multiple pages, set the document so that the first page is on the same side as the ADF paper chute. Load the document with its front side facing the ADF paper chute.(face down) 36 3.2 Loading Documents on the ADF for Scanning
  • Fujitsu FI 4220C | Operator Manual - Page 66
    , pull out the ADF paper chute extension. Extension 3 4. Move the side guides until they match the width of the document. Move the side guides to eliminate gaps between the side guides and the document. If there are gaps between the side guides and the document, the document is sometimes scanned in
  • Fujitsu FI 4220C | Operator Manual - Page 67
    fingertips into the indentations on the scanner as shown in below figure. Indentation 5. Start up the scanner application, and scan the document. For details on how to scan documents using the ScandAll 21 application, see "3.4 Scanning Documents." 38 3.2 Loading Documents on the ADF for Scanning
  • Fujitsu FI 4220C | Operator Manual - Page 68
    BASIC SCANNER OPERATIONS 3.3 Loading Documents on the Flatbed for Scanning The following describes how to load documents on the Flatbed. 1. Lift up the document cover. 3 3.3 Loading Documents on the Flatbed for Scanning 39
  • Fujitsu FI 4220C | Operator Manual - Page 69
    with the reference point. ABC Reference point 3. Gently close the document cover. 4. Start up the scanner application, and scan the document. For details on how to scan documents using the ScandAll 21 application, see "3.4 Scanning Documents." 40 3.3 Loading Documents on the Flatbed for Scanning
  • Fujitsu FI 4220C | Operator Manual - Page 70
    on the scanner's ADF paper chute or Flatbed. For details on how to load documents, see "3.2 Loading Documents on the ADF for Scanning" and "3.3 Loading Documents on the Flatbed for Scanning." 2. Start up ScandAll 21. 3 Select [Program] - [Scanner Utility for Microsoft Windows] [ScandAll 21] in
  • Fujitsu FI 4220C | Operator Manual - Page 71
    conditions) appears. 5. Set the scan resolution, paper size and other scan conditions, and click the [Scan] button. For details on settings in the [TWAIN Driver] dialog box, refer to the Scanner Utility for Microsoft® Windows® User's Guide on the scanner driver CD-ROM. 42 3.4 Scanning Documents
  • Fujitsu FI 4220C | Operator Manual - Page 72
    BASIC SCANNER OPERATIONS 3 3.4 Scanning Documents 43
  • Fujitsu FI 4220C | Operator Manual - Page 73
    The document is scanned, and an image of the scanned document appears on the ScandAll 21 screen. For details on scanning various other documents, see "Chapter4, SCANNING VARIOUS TYPES OF DOCUMENTS." For details on ScanAll 21 functions and operations, refer to ScandAll 21 Help. 44 3.4 Scanning
  • Fujitsu FI 4220C | Operator Manual - Page 74
    chapter describes how to scan various types of documents. This chapter explains samples of the screens in Windows® XP. The screens and operations may differ slightly if the OS that you are using is other than Windows® XP. Also, when FUJITSU TWAIN32 is updated the screens and 4 operations noted
  • Fujitsu FI 4220C | Operator Manual - Page 75
    4.1 Scanning in Books Never look directly into the light source during CAUTION scanning. The following describes how to scan pages in books. 1. Open the document cover. 2. Remove the document cover as shown in below figure. 46 4.1 Scanning in Books
  • Fujitsu FI 4220C | Operator Manual - Page 76
    SCANNING VARIOUS TYPES OF DOCUMENTS 4. Issue the scan command on the host system. For details on scanning commands, see "3.4 Scanning Documents." 4 ATTENTION Do not move the document during scanning. 5. When scanning ends, re-attach and gently close the document cover. 4.1 Scanning in Books
  • Fujitsu FI 4220C | Operator Manual - Page 77
    4.2 Scanning Documents Larger Than A4 In Size Never look directly at the light source during CAUTION scanning. The following describes how to scan documents larger than A4 in size. 1. Remove the document cover as shown in below figure. 48 4.2 Scanning Documents Larger Than A4 In Size
  • Fujitsu FI 4220C | Operator Manual - Page 78
    the host system. For details on scanning commands, see "3.4 Scanning Documents." Do not move the document during 4 ATTENTION scanning. 4. When scanning ends, re-attach and gently close the document cover. SCANNING VARIOUS TYPES OF DOCUMENTS 4.2 Scanning Documents Larger Than A4 In Size 49
  • Fujitsu FI 4220C | Operator Manual - Page 79
    together on the ADF, smaller-width documents sometimes are scanned in skewed. Be sure to scan only documents having the same width. The following shows the procedure for reading the manuscript with which width is different. 1. Sorted to the stack of the same width. 2. Side guide unites with the
  • Fujitsu FI 4220C | Operator Manual - Page 80
    on the PC you are using. Adobe Acrobat5.0 can be installed from the Adobe Acrobat5.0 CDROM provided. The following shows the procedure for saving scanned images in PDF format. 1. Load the document on the ADF paper chute. 2. Start up Adobe Acrobat5.0. Select [Program] - [Adobe Acrobat5.0] in that
  • Fujitsu FI 4220C | Operator Manual - Page 81
    3. Select [Import] - [Scan...] in that order from the [File] menu. The [Acrobat Scan Plug-in] dialog box appears. 52 4.4 Saving Scanned Images in PDF Format
  • Fujitsu FI 4220C | Operator Manual - Page 82
    "FUJITSU fi-4220Cdj"(Windows® 95 and WindowsNT® 4.0, select "FUJITSU TWAIN 32") at "Device" and click the [Scan] button. The [TWAIN Driver] dialog box appears. ATTENTION Also select "Simplex" when scanning double-sided documents. 4 SCANNING VARIOUS TYPES OF DOCUMENTS 4.4 Saving Scanned Images
  • Fujitsu FI 4220C | Operator Manual - Page 83
    5. Set the scan resolution, paper size and other scan conditions, and click the [Scan] button. Scanning starts, and a message for selecting whether or not to continue scanning appears. 54 4.4 Saving Scanned Images in PDF Format
  • Fujitsu FI 4220C | Operator Manual - Page 84
    6. To end scanning, click the [Done] button. The scanned image appears. Save the scanned image on Adobe Acrobat5.0. For details on Adobe Acrobat5.0 operations, refer to the Adobe 4 Acrobat5.0 manual and Help. SCANNING VARIOUS TYPES OF DOCUMENTS 4.4 Saving Scanned Images in PDF Format 55
  • Fujitsu FI 4220C | Operator Manual - Page 85
    the document (i.e. the color green is "dropped out"). To set the scanner to scan documents with a selected color dropped out, change the settings in the [TWAIN Driver] dialog box. The following shows the procedure for changing the settings in this dialog box. 56 4.5 Excluding a Color in the Image
  • Fujitsu FI 4220C | Operator Manual - Page 86
    1. Click the [Advance...] button in the [TWAIN Driver] dialog box. 4 The [Advance] dialog box appears. 2. Select the color to drop out from "Dropout Color" under "More". 4.5 Excluding a Color in the Image(dropout color) 57 SCANNING VARIOUS TYPES OF DOCUMENTS
  • Fujitsu FI 4220C | Operator Manual - Page 87
    3. For example, to scan only black text areas when scanning black text surrounded by a green frame, select [Green]. 4. Click the [OK] button. The [TWAIN Driver] dialog box will be redisplayed. Continue scanning from this dialog box. 58 4.5 Excluding a Color in the Image(dropout color)
  • Fujitsu FI 4220C | Operator Manual - Page 88
    two or more sheets in the ADF paper chute are fed simultaneously into the scanner. You can set the scanner to detect double-feed, stop scanner operation, and display an error message. To set the scanner to detect double-feed, change the settings in the [TWAIN Driver] dialog box. The following shows
  • Fujitsu FI 4220C | Operator Manual - Page 89
    1. Click the [Option...] button in the [TWAIN Driver] dialog box. The [Option] dialog box appears. 2. Click the [Option] tab. 60 4.6 Detecting Double-feeds
  • Fujitsu FI 4220C | Operator Manual - Page 90
    conditions from "Double Feed" under "ADF Option". SCANNING VARIOUS TYPES OF DOCUMENTS The following detection conditions are provided: 4 None Check thickness : Double-feed detection is not performed : The scanner uses a sensor to monitor the thickness of documents that are fed. It detects
  • Fujitsu FI 4220C | Operator Manual - Page 91
    and length : The scanner monitors both document thickness and length to detect doublefeed. Furthermore, see "8.5 Double-feed Detection Conditions" for detailed information about the document for double-feed detection. 4. Click the [OK] button. The display returns to the [TWAIN Driver] dialog box
  • Fujitsu FI 4220C | Operator Manual - Page 92
    5 DAILY CARE This chapter describes how to clean the scanner. WARNING When cleaning the scanner, turn off the power, and unplug the AC cable from the outlet. 5 DAILY CARE 5.1 Cleaning Materials and Locations and Cleaning Cycle 64 5.2 Cleaning the Flatbed 66 5.3 Cleaning the ADF 69 63
  • Fujitsu FI 4220C | Operator Manual - Page 93
    , dry cloth For details on Cleaner F1, consult the agent where you bought your scanner. I Locations That Needs To Be Cleaned Same location in the ADF and Flatbed must be cleaned regularly with a soft, dry cloth moistened with Cleaner F1. 64 5.1 Cleaning Materials and Locations and Cleaning Cycle
  • Fujitsu FI 4220C | Operator Manual - Page 94
    every 1000 scanned sheets. Pick roller Feed roller Plastic roller Sheet guide Glass Document holding pad Document bed 5 The scanner must be cleaned more frequently ATTENTION when the following documents are used: •Documents of coated paper DAILY CARE •Documents with printed text or
  • Fujitsu FI 4220C | Operator Manual - Page 95
    windows or glass cleaner can be used instead of cleaning fluid. However, do not use paint thinner or other organic solvents. • Do not allow moisture to get inside the device during cleaning. I Cleaning the Flatbed The following parts needs to be cleaned in the Flatbed area: •Document holding
  • Fujitsu FI 4220C | Operator Manual - Page 96
    The following shows how to clean the Flatbed. 1. Open the document cover. 2. Clean the following locations using a soft, dry cloth moistened with cleaning fluid. Document holding pad 5 Document bed DAILY CARE 5.2 Cleaning the Flatbed 67
  • Fujitsu FI 4220C | Operator Manual - Page 97
    •Document holding pad Wipe gently. •Document bed Wipe lightly. ATTENTION Do not allow moisture to get inside the device during cleaning. 3. Wait for cleaned parts to dry. 4. Gently close the document cover. 68 5.2 Cleaning the Flatbed
  • Fujitsu FI 4220C | Operator Manual - Page 98
    scanner is in use, the surface of the glass inside the ADF becomes hot. Before cleaning ADF, disconnect the AC adapter from the power outlet, and wait at least 15 minutes for the glass to cool down. I Cleaning the ADF The following parts needs to be cleaned in the ADF unit: •Pad ASY •Pick roller
  • Fujitsu FI 4220C | Operator Manual - Page 99
    The following shows the procedure for cleaning the ADF. 1. Open the ADF by pushing on the ADF button and turning the ADF cover to the front. The front portion ADF button Be careful, the ADF cover may close and CAUTION pinch your finger. 70 5.3 Cleaning the ADF
  • Fujitsu FI 4220C | Operator Manual - Page 100
    2. Clean the following locations with a soft, dry cloth moistened with Cleaner F1. Feed rollers (Four pieces) Pad ASY Sheet guide (A white portion, Two parts) DAILY CARE 5 Pick roller (One pieces) Glass(Two parts) Plastic rollers (Four pieces) 5.3 Cleaning the ADF 71
  • Fujitsu FI 4220C | Operator Manual - Page 101
    to clean •Pick roller Lightly clean the Pick rollers taking care not to scratch the roller surfaces and the Mylar sheet. Take particular care when cleaning these rollers, as black foreign matter on these rollers affects document pick performance. Mylar sheet (Transparent) 72 5.3 Cleaning the ADF
  • Fujitsu FI 4220C | Operator Manual - Page 102
    cleaning fluid against the surface of the rotating Feed rollers so that it lightly cleans the surface of the rollers. Take particular care when cleaning these rollers as black foreign matter on these rollers affects document pick performance. 5 As a guideline, seven simultaneous presses of the
  • Fujitsu FI 4220C | Operator Manual - Page 103
    •Sheet guide(Especially a white portion) Clean lightly. • Glass Clean lightly. HINT When white portion of the sheet guide or glass surface become dirty, black vertical streaks sometimes appear in the scanned image. 74 5.3 Cleaning the ADF
  • Fujitsu FI 4220C | Operator Manual - Page 104
    return it to its original position until the ADF button locks. Press center of ADF. ATTENTION After the ADF is returned to its original position, make sure that the ADF is completely closed. An incompletely closed ADF might cause document jams or scanning problems. 5 DAILY CARE 5.3 Cleaning the
  • Fujitsu FI 4220C | Operator Manual - Page 105
    76 5.3 Cleaning the ADF
  • Fujitsu FI 4220C | Operator Manual - Page 106
    you are using is other than Windows® XP. Also, when FUJITSU TWAIN32 is updated the screens and operations noted in this chapter will differ slightly. WARNING Turn off the power and unplug the AC adapter from the outlet when changing the scanners consumable products. 6.1 Consumable and Replacement
  • Fujitsu FI 4220C | Operator Manual - Page 107
    their standard replacement cycle. Description Pad ASY Pick roller Specifications Standard Replacement Cycle PA03289-0002 50,000 paper • The paper that meets the quality of Section 8.2 This cycle varies according to the document being used, and how frequently the user uses and cleans the scanner
  • Fujitsu FI 4220C | Operator Manual - Page 108
    shows the procedure for doing this. 1. When turning on the power, check that the scanner and the personal computer are 6 connected. See "2.2 Connecting the Scanner to a PC" for information about connecting the scanner to a personal computer. 2. Double click the "Printer and Other Hardware
  • Fujitsu FI 4220C | Operator Manual - Page 109
    3. In the [Printer and Other Hardware] screen, double click the "Scanners and Cameras" icon. The [Scanners and Cameras] screen is displayed. 80 6.1 Consumable and Replacement Cycle
  • Fujitsu FI 4220C | Operator Manual - Page 110
    REPLACING CONSUMABLES 4. Double click the "fi-4220Cdj". (Windows® 95 and WindowsNT® 4.0, select "FUJITSU TWAIN 32" icon Select at "Device" and click the [Properties] button.) 6 6.1 Consumable and Replacement Cycle 81
  • Fujitsu FI 4220C | Operator Manual - Page 111
    The [fi-4220Cdj Properties] dialog box appears. 82 6.1 Consumable and Replacement Cycle
  • Fujitsu FI 4220C | Operator Manual - Page 112
    You can confirm the following information in this panel: • Total number of scans • Pad counter (approximate number of documents scanned after replacing the Pad ASY) • Pick roller counter (approximate number of documents scanned after replacing the Pick roller) 6.1 Consumable and Replacement Cycle 83
  • Fujitsu FI 4220C | Operator Manual - Page 113
    the scanner is document sheets is finished, click the [Ignore] button. To discontinue scanning, and replace the consumables immediately, click the [Cancel] button. 3) Replace the consumables. For details on how to replace consumables, see "6.2 Replacing the Pad ASY" and "6.3 Replacing the Pick Roller
  • Fujitsu FI 4220C | Operator Manual - Page 114
    the [Warms again after scanning 100 pages] checkbox. 2) To continue scanning of the current document, click the [Ignore] button. To discontinue scanning, click the [Cancel] button. 3) , see "6.2 Replacing the Pad ASY" and "6.3 Replacing the Pick Roller." 6.1 Consumable and Replacement Cycle 85
  • Fujitsu FI 4220C | Operator Manual - Page 115
    shows the procedure for replacing the Pad ASY. 1. Remove any documents on the ADF paper chute. 2. Open the ADF by pushing on the ADF button and turning the ADF cover to the front. The front portion ADF button Be careful, the ADF cover may close and CAUTION pinch your finger. 86 6.2 Replacing
  • Fujitsu FI 4220C | Operator Manual - Page 116
    ends of the new Pad ASY and attach it to its installation location. When doing this, take care not to catch the pick springs. ATTENTION Make sure that the Pad ASY is completely attached. An incompletely attached Pad ASY might cause document jams or other feed errors. 6.2 Replacing the Pad ASY 87
  • Fujitsu FI 4220C | Operator Manual - Page 117
    original position and lock the ADF button. Press center of ADF. 6. Reset the pad counter. The following shows the procedure for resetting the pad counter. • For Windows® 98 / Windows® Me / Windows® 2000 / Windows® XP 1) When turning on the power, check that the scanner and the personal computer are
  • Fujitsu FI 4220C | Operator Manual - Page 118
    REPLACING CONSUMABLES 4) Double click the "fi-4220Cdj". 5) Click the "Device Set" tab. The following panel appears. 6 After clicking the [Clear] button beside the "Pad Counter" in "Page Counter", click the [OK] button. This returns the pad counter to "0". 6.2 Replacing the Pad ASY 89
  • Fujitsu FI 4220C | Operator Manual - Page 119
    • For Windows® 95 / Windows NT® 4.0 1) When turning on the power, check that the scanner and the personal computer are connected. 2) Right click the "FUJITSU Scanner Control Center" icon displayed in the task tray, then select "Option" 3) Double click "Scanner Information". The following screen is
  • Fujitsu FI 4220C | Operator Manual - Page 120
    REPLACING CONSUMABLES 4) Click the "Pad Counter Reset" button. The following message is displayed. 6 Click "Yes". The Pad counter (The pad counts) returns to "0". 6.2 Replacing the Pad ASY 91
  • Fujitsu FI 4220C | Operator Manual - Page 121
    6.3 Replacing the Pick Roller The following shows the procedure for replacing the Pick roller. 1. Remove any documents on the ADF paper chute. 2. Remove the ADF paper chute. ADF paper chute 92 6.3 Replacing the Pick Roller
  • Fujitsu FI 4220C | Operator Manual - Page 122
    REPLACING CONSUMABLES 3. Open the ADF by pushing on the ADF button and turning the ADF cover to the front. The front portion 6 ADF button Be careful, the ADF cover may close and CAUTION pinch your finger. 6.3 Replacing the Pick Roller 93
  • Fujitsu FI 4220C | Operator Manual - Page 123
    4. Remove the Pick roller from a scanner. 1) Grip the knobs on the sheet guide between you fingers, and lift up to remove. 2) Rotate the Pick roller bushing in the direction of the arrow. Pick roller bushing 94 6.3 Replacing the Pick Roller
  • Fujitsu FI 4220C | Operator Manual - Page 124
    up in the direction of the arrow. 6 REPLACING CONSUMABLES CAUTION The Pick roller Bushing is hard. Do not turn this bearing with your fingernails. 4) Remove the Pick roller from the shaft while lifting up the tab on the Pick roller. tab Shaft Lift up. Pull shaft to remove. 6.3 Replacing the
  • Fujitsu FI 4220C | Operator Manual - Page 125
    5. Attach the new Pick roller. Insert the new Pick roller aligning the protrusion on the axis with the groove in the Pick roller. Protrusion Groove ATTENTION Make sure that the Pick roller is completely attached. An incompletely attached Pick roller might cause document jams or other feed errors
  • Fujitsu FI 4220C | Operator Manual - Page 126
    removing the Pick roller from the scanner. After attaching the Pick roller to the scanner, perform the following procedure to fix it in place. 6 1) Turn the Pick roller bushing in the direction indicated by the arrow. Pick roller bushing REPLACING CONSUMABLES 2) Move the sheet guide claws in
  • Fujitsu FI 4220C | Operator Manual - Page 127
    7. Press down on the center of the ADF to return it to its original position and lock the ADF button. Press center of ADF. 8. Attach the ADF paper chute. ADF paper chute 98 6.3 Replacing the Pick Roller
  • Fujitsu FI 4220C | Operator Manual - Page 128
    the pick counter. • For Windows® 98 / Windows® Me / Windows® 2000 / Windows® XP 1) When turning on the power, check that the scanner and screen, double click the "Scanners and Cameras" icon. The [Scanners and Cameras] screen is displayed. REPLACING CONSUMABLES 6.3 Replacing the Pick Roller 99
  • Fujitsu FI 4220C | Operator Manual - Page 129
    4) Double click the "fi-4220Cdj". 5) Click the "Device Set" tab. The following panel appears. After clicking the [Clear] button beside the "Pick Counter" in "Page Counter", click the [OK] button. This returns the pick counter to "0". 100 6.3 Replacing the Pick Roller
  • Fujitsu FI 4220C | Operator Manual - Page 130
    the scanner and the personal computer are connected. 2) Right click the "FUJITSU Scanner Control Center" icon displayed in the task tray, then select "Option" 6 3) Double click "Scanner Information". The following screen is displayed. REPLACING CONSUMABLES 6.3 Replacing the Pick Roller 101
  • Fujitsu FI 4220C | Operator Manual - Page 131
    4) Click the "Pick Counter Reset" button. The following message is displayed. Click "Yes". The Pick counter (The Pick roller counts) returns to "0". 102 6.3 Replacing the Pick Roller
  • Fujitsu FI 4220C | Operator Manual - Page 132
    other than the contents indicated, and the details of an error, refer to the Scanner Utility for Microsoft® Windows® User's Guide on the scanner driver CD-ROM. 7.1 Removing Jammed Documents 104 7.2 Remedying Typical Troubles 107 7.3 Items to check before contacting the agent where you bought the
  • Fujitsu FI 4220C | Operator Manual - Page 133
    surface of the glass sometimes becomes hot during operation. Take care to prevent burns. HINT For details on how to clean the ADF, see "5.3 Cleaning the ADF." The following shows the procedure for removing jammed documents. 1. Remove any documents on the ADF paper chute. 104 7.1 Removing Jammed
  • Fujitsu FI 4220C | Operator Manual - Page 134
    2. Open the ADF by pushing on the ADF button and turning the ADF cover to the front. The front portion 7 TROUBLESHOOTING ADF button Be careful, the ADF cover may close and CAUTION pinch your finger. 3. Remove the jammed document. ATTENTION • Staples, paper clips, etc. cause document jams. Be
  • Fujitsu FI 4220C | Operator Manual - Page 135
    4. Press down on the center of the ADF to return it to its original position and lock the ADF button. Press center of ADF. ATTENTION Make sure that the ADF is completely closed. An incompletely closed ADF might cause document jams or scanning problems. 106 7.1 Removing Jammed Documents
  • Fujitsu FI 4220C | Operator Manual - Page 136
    following flowcharts. If the remedies in these flowcharts do not solve the problem, check the items in "7.3 Items to check before contacting the agent where you bought the scanner" and then contact the agent where you bought the scanner. 7 TROUBLESHOOTING 7.2 Remedying Typical Troubles 107
  • Fujitsu FI 4220C | Operator Manual - Page 137
    Symptom1 Scanner does not turn ON. Are power cord and AC adapter correctly connected? NO Correctly connect power cord. YES Have you pushed the power button? YES Contact the manufacturer's authorized service center. NO Press power button. 108 7.2 Remedying Typical Troubles
  • Fujitsu FI 4220C | Operator Manual - Page 138
    Power Save mode. Press any button on control panel to start up scanner. NO Does the display remain blank even after you have turned on NO Scanner operation is normal. 7 the power again? YES Contact the manufacturer's authorized service center. TROUBLESHOOTING 7.2 Remedying Typical Troubles
  • Fujitsu FI 4220C | Operator Manual - Page 139
    paper chute? YES ADF closed completely? NO Set transport lever to correct position. NO Load document correctly on ADF paper chute. NO Close ADF completely. YES Interface cable connected correctly? YES NO Connect interface cable correctly. Continued on next page 110 7.2 Remedying Typical Troubles
  • Fujitsu FI 4220C | Operator Manual - Page 140
    rear of scanner. Scanner operation is normal. YES Does the alarm state remain displayed even after the scanner has been turned off and back on again? YES NO Scanner operation is normal. Contact the manufacturer's authorized service center. 7 TROUBLESHOOTING 7.2 Remedying Typical Troubles 111
  • Fujitsu FI 4220C | Operator Manual - Page 141
    or dithering selected? NO Select halftoning or dithering on host computer. YES Document glass, document press pad, glass, and sheet guides(A white portion) clean? YES Contact the manufacturer's authorized service center. NO Clean dirty locations.(*) *) For details on how to clean dirty
  • Fujitsu FI 4220C | Operator Manual - Page 142
    Document glass, document press pad, glass, and sheet guides(A white portion) clean? NO Clean dirty locations.(*) YES 7 Contact the manufacturer's authorized service center. *) For details on how to clean dirty locations, see "Chapter5, DAILY CARE." TROUBLESHOOTING 7.2 Remedying Typical Troubles
  • Fujitsu FI 4220C | Operator Manual - Page 143
    document press pad, glass, and sheet guides(A white portion) clean? YES NO Clean dirty locations.(*) Top cover of ADF pressed down or heavy object placed on ADF during scanning by ADF? YES Do not press down ADF or place heavy objects on ADF during scanning. NO Is something causing the scanner
  • Fujitsu FI 4220C | Operator Manual - Page 144
    NO surface or scanner missing rubber foot? Install scanner on flat, level surface or attach rubber foot. YES Contact the manufacturer's 7 authorized service center. *) For details on how to clean dirty locations, see "Chapter5, DAILY CARE." TROUBLESHOOTING 7.2 Remedying Typical Troubles 115
  • Fujitsu FI 4220C | Operator Manual - Page 145
    streaks appear in scanned image. Document scanned on flat bed? YES Contact the manufacturer's authorized service center. NO White streaks? YES Clean Sheet guide(A white portion)(*) NO Black streaks? YES Clean glass.(*) NO Contact the manufacturer's authorized service center. *) For details
  • Fujitsu FI 4220C | Operator Manual - Page 146
    operating position? NO Set transport lever to correct position. YES 7 Turn scanner OFF and then ON NO Scanner operation is again. normal. Function No. display indicates alarm? YES Contact the manufacturer's authorized service center. TROUBLESHOOTING 7.2 Remedying Typical Troubles 117
  • Fujitsu FI 4220C | Operator Manual - Page 147
    fanned before loading on document support? YES Document recently printed on a copier or laser printer? NO Fan document before loading, or reduce number of sheets in document to be loaded. YES Fan 3 or 4 times to remove static electricity from paper. NO Document stack 5mm or less? NO Reduce
  • Fujitsu FI 4220C | Operator Manual - Page 148
    7 Pad ASY attached correctly? NO Attach Pad ASY correctly.(*4) YES Contact the manufacturer's authorized service center. TROUBLESHOOTING *1) For details on requirements, see "8.2 Document Quality." *2) For details on double-feed, see "8.5 Double-feed Detection Conditions." *3) For details on
  • Fujitsu FI 4220C | Operator Manual - Page 149
    NO on ADF paper chute? YES Pad ASY attached correctly? NO Use document which is satisfying requirements. (*1) Fan document before loading, or reduce number of sheets in document to be loaded. Attach Pad ASY correctly.(*2) YES Pick roller dirty? YES Clean Pick roller.(*3) NO Pick roller worn
  • Fujitsu FI 4220C | Operator Manual - Page 150
    TROUBLESHOOTING *1) For details on requirements, see "8.2 Document Quality." *2) For details on how to attach the Pad ASY, see "6.2 Replacing the Pad ASY." *3) For details on how to clean the Pick roller, see "5.3 Cleaning the ADF." *4) For details on how to replace the Pick roller, see "6.3
  • Fujitsu FI 4220C | Operator Manual - Page 151
    in "8.2 Document Paper Quality"? YES Foreign objects in ADF? YES Use document which is satisfying requirements. (*1) Clean ADF or remove any foreign objects.(*2) NO Pad ASY attached corrected? NO Attach Pad ASY correctly. (*3) YES Contact the manufacturer's authorized service center. *1) For
  • Fujitsu FI 4220C | Operator Manual - Page 152
    Clean all of the rollers (*1) YES Contact the manufacturer's authorized service center. 7 TROUBLESHOOTING NO Set the scan scale. What OS are you using? Windows R 98/ Windows R Me/ Windows R 2000/ Windows R XP Display the properties of the scanner that you are using on "Scanners and Cameras" in
  • Fujitsu FI 4220C | Operator Manual - Page 153
    R 95/ Windows NT R 4.0 YES Is the Scanner Control Center icon displayed in the task tray? NO Select [FUJITSU Scanner Control Center] from the Start menu and run it. Right click the Scanner Control Center icon and select [Options] then adjust the scan scale. 124 7.2 Remedying Typical Troubles
  • Fujitsu FI 4220C | Operator Manual - Page 154
    start scanning the document)? NO Do the offset adjustment. What OS are you using? YES Contact the manufacturer's authorized service center. 7 TROUBLESHOOTING Windows R 98/ Windows R Me/ Windows R 2000/ Windows R XP Windows R 95/ Windows NT R 4.0 Display the properties of the scanner that you
  • Fujitsu FI 4220C | Operator Manual - Page 155
    7.3 Items to check before contacting the agent where you bought the scanner Check the following items before you contact the agent where you bought the scanner. 126 7.3 Items to check before contacting the agent where you bought the scanner
  • Fujitsu FI 4220C | Operator Manual - Page 156
    I General Details Item Model findings (Example) fi-4220C For details on model, see "7.4 Checking Labels on the Scanner." Serial No. (Example) 000001 7 For details on serial No., see "7.4 Check- ing Labels on the Scanner." TROUBLESHOOTING Production date (Example) 2002-4 (April, 2002) For
  • Fujitsu FI 4220C | Operator Manual - Page 157
    I Installation or PC connection issues I problem at the time of personal computer connection Item OS Displayed error message Interface findings (Example) SCSI interface Interface controllers (Example) made by Adaptec SCSI Card 2940Au I Feed system trouble Item Document type Main purpose of use
  • Fujitsu FI 4220C | Operator Manual - Page 158
    findings Type and version of scanner driver Type of interface controller (Example) made by Adaptec SCSI Card 2940Au OS (Windows®) Software application 7 (Example) ScandAll 21 (Example) Acrobat TROUBLESHOOTING I Other Item Can both the original document and scanner image be sent by e-mail or
  • Fujitsu FI 4220C | Operator Manual - Page 159
    7.4 Checking Labels on the Scanner This section describes how to check the labels on the scanner. I Positions of Labels on the Scanner The following shows where the two labels are located on the scanner. Label A Label B Label A (example): Indicates scanner information. 130 7.4 Checking Labels on
  • Fujitsu FI 4220C | Operator Manual - Page 160
    TROUBLESHOOTING Label B (example): Indicates scanner conformity with various standards. 7 7.4 Checking Labels on the Scanner 131
  • Fujitsu FI 4220C | Operator Manual - Page 161
    132 7.4 Checking Labels on the Scanner
  • Fujitsu FI 4220C | Operator Manual - Page 162
    This chapter describes the required document size and paper quality for ensuring correct operation when scanning documents on 8 the ADF. ADF AND PAPER SPECIFICATION 8.1 Document Size 134 8.2 Document Quality 135 8.3 Maximum Document Loading Capacity 139 8.4 Hole-punching Prohibited
  • Fujitsu FI 4220C | Operator Manual - Page 163
    8.1 Document Size The following shows the size of documents that can be scanned on the ADF. A Feeding Direction B Maximum Minimum A B A B 216 (8.5 in) 356 (14 in) 53 (2.1 in) 74 (2.9 in) (Unit : mm) 134 8.1 Document Size
  • Fujitsu FI 4220C | Operator Manual - Page 164
    the actual document. I Document Thickness Paper thickness is expressed by "paper weight." The following shows the paper weights that can be used on this scanner: • 52g/m2 to 127g/m2 Only a paper weight of 127g/m2 is allowed for A8-size documents. ADF AND PAPER SPECIFICATION 8.2 Document Quality
  • Fujitsu FI 4220C | Operator Manual - Page 165
    scanned successfully on the ADF. To prevent unexpected trouble, a feed test using a spare document may be needed. If documents slip frequently, or paper jams or double-feeds occur, load the document on the Flatbed for scanning. • Paper-clipped or stapled documents • Ink documents that are still wet
  • Fujitsu FI 4220C | Operator Manual - Page 166
    For details on cleaning the Pad ASY and Pick rollers, see "5.3 Cleaning the ADF." Replacing parts: The service life of the Pad ASY and Pick rollers is sometimes shortened when scanning mediumgrade paper documents. • When the manuscript of Wood containg paper is read, the life of a Pad ASY and
  • Fujitsu FI 4220C | Operator Manual - Page 167
    HINT When using the ADF, the leading edge of all document sheets must be evenly aligned. Make sure that curling at the leading edge is within the following tolerances: More than 30mm Feed direction Less than 3mm Top of the paper Read surface More than 30mm Feed direction Less than 5mm Top of
  • Fujitsu FI 4220C | Operator Manual - Page 168
    paper chute is determined by the size and weight of the document. The following graph shows the maximum document loading capacity of ADF according to paper weight. 60 50 Capacity (number of of ADF 40 pages) 30 20 Legal 60 50 50 41 A4 / Letter or smaller 8 35 29 29 24 0 52 64 80
  • Fujitsu FI 4220C | Operator Manual - Page 169
    When using the ADF, document trouble might occur if there are punched holes in the shaded area in the following figure. If holepunched documents must be scanned, use the Flatbed. Read reference 35 position Top of paper Front side Feeding direction Bottom of paper Center of paper (Unit : mm
  • Fujitsu FI 4220C | Operator Manual - Page 170
    modes. I Detection by Document Thickness Sheets of the same thickness shall be set in the ADF at a time. • Document thickness: 0.065 to 0.15mm the leading edge of the document. • Punched holes are not allowed within 35mm of the vertical center line of the document. • The deviation in the
  • Fujitsu FI 4220C | Operator Manual - Page 171
    Length Sheets of the same length shall be set in the ADF at a time. • Document length deviation: 1% or less • Printed area: 12% or less • No black printed areas are allowed at the center area (26 x 10mm) at the leading edge of the document. • Punched holes are not allowed within 35mm of the vertical
  • Fujitsu FI 4220C | Operator Manual - Page 172
    ADF AND PAPER SPECIFICATION I Detection by Document Thickness and Length Sheets of the same thickness and length shall be set in the ADF at a time. • Document length: 0.065 to 0.15mm • Document length deviation: 1% or less • Printed area: 12% or less • No black printed areas are allowed at the
  • Fujitsu FI 4220C | Operator Manual - Page 173
    No printing allowed 35mm 26mm 10mm Feeding direction No punched holes allowed Center of paper 144 8.5 Double-feed Detection Conditions
  • Fujitsu FI 4220C | Operator Manual - Page 174
    9 SCANNER SPECIFICATION This chapter lists the scanner specifications. 9 9.1 Basic Specifications 146 9.2 Installation Specifications 149 9.3 External Dimensions 151 145 SCANNER SPECIFICATION
  • Fujitsu FI 4220C | Operator Manual - Page 175
    1 Scanner Type ADF(Automatic - Document Feeder), Flatbed 2 Image sensor CCD x 3 Front / Back / Flatbed 3 Light source Incandescent cold Front / Back / cathode fluorescent Flatbed lamp x 3 4 Scanning Mini- area mum A8(Note(*1)) ADF 127g/m2 paper Maxi- A4 (Flatbed) / - mum Legal (ADF
  • Fujitsu FI 4220C | Operator Manual - Page 176
    the ADF to scan. When using the Flatbed to scan the scanning range is unlimited. *2) The manuscript thicknesses noted are for when using the ADF. When using the Flatbed to scan the manuscript thickness is unlimited. For details, see "Chapter8, ADF AND PAPER SPECIFICATION." SCANNER SPECIFICATION
  • Fujitsu FI 4220C | Operator Manual - Page 177
    scanner hardware. Software processing time such as data transfer time is added to the actual scanning time. *4) The scanning speed noted is the value when using the ADF to scan. *5) The maximum stacking capacity varies according to the document thickness. For details, see "Chapter8, ADF AND PAPER
  • Fujitsu FI 4220C | Operator Manual - Page 178
    The following table shows specifications related to scanner installation. Item Specification Dimensions (mm) (Without ADF paper chute) Depth 569 (22.4 in) Width 302 (11.9 in) Height 229 (9.0 in) Installation Space (mm) 800 (31.5in) x 400 (15.8in) x 450 (17.8in) (D x W x H) Weight
  • Fujitsu FI 4220C | Operator Manual - Page 179
    Item Specification Ambient condition Device status Temperature Operating 5 to 35 °C (41 to 95°F) Not operating -20 to 60 °C (-4 to 140°F) Humidity 20 to 80 % 8 to 95 % Heat capacity 29.3 kcal / H or less Shipping Weight (kg) 11.5 kg (25.4 lb) 150 9.2 Installation Specifications
  • Fujitsu FI 4220C | Operator Manual - Page 180
    9.3 External Dimensions The following shows the external dimensions of the fi-4220C. 302 (11.9") 9 229 (9") 305 (12") SCANNER SPECIFICATION 569(22.4") 537(21.2") (Unit : mm) 9.3 External Dimensions 151
  • Fujitsu FI 4220C | Operator Manual - Page 181
    152 9.3 External Dimensions
  • Fujitsu FI 4220C | Operator Manual - Page 182
    Code for Information Interchange. ASCII is a set of 256 codes (numbered 0 to 255) used to communicate information between a computer and another device such as a scanner. Backside reading = Back-side scanning Refers to reading the backside of the document, specifically in Duplex reading mode. GL-1
  • Fujitsu FI 4220C | Operator Manual - Page 183
    sheets by the ADF unit. Can be turned on or off by the operator. Double Letter Size A standard paper size used in the U.S.A. and other countries. Paper size is 11 x 17 inches. dpi Dots per inch. Dropout color A color which is used in the document but does not appear in the read image. Duplex reading
  • Fujitsu FI 4220C | Operator Manual - Page 184
    such as newspaper photographs. Filtering A correction method that improves the read quality of handwritten documents. The read quality of images written in pencil or ballpointed pen depends on the reflective light characteristics of the specific ink or lead used. Dropped pixels may produce outlines
  • Fujitsu FI 4220C | Operator Manual - Page 185
    . Interface The connection that allows communication from one part of a system to another. For example, electrical signals are transferred between the computer and scanner over an interface cable. Inversion (Reverse-image reading) In reverse-image reading, data is changed from black to white
  • Fujitsu FI 4220C | Operator Manual - Page 186
    operator to feed each document manually into the ADF paper chute. Manual start mode ( automatic start mode) The reading operation is activated by pressing the START button in this mode. Available only when video option board is installed. Mirror image The read image is symmetrically flipped to
  • Fujitsu FI 4220C | Operator Manual - Page 187
    is used to control scanner operations such as loading document, selecting features, and changing setup options. Outline extraction The boundary between black and white areas is traced and the outline extracted for closed areas. PAPER JAM A warning informing the user that document is jammed in the
  • Fujitsu FI 4220C | Operator Manual - Page 188
    front side of the document is read in this mode. Place the documents face up at the center of the ADF paper chute. Smoothing A process that is the time the scanner waits for next document insertion after the last document feeding. The scanner returns Paper Empty when no document is set after time-
  • Fujitsu FI 4220C | Operator Manual - Page 189
    GL-8
  • Fujitsu FI 4220C | Operator Manual - Page 190
    INDEX A AC adapter 3 AC cable 3 ADF button 5 ADF Paper Chute 5 ADF(Automatic document feeder 5 Ambient condition 150 B Buttons Function button 12 Power button 12 Scan button 12 Send to button 12 C Capacity of ADF 147 Cleaning Cleaning the ADF........... 69 Cleaning the Flat bed .... 66
  • Fujitsu FI 4220C | Operator Manual - Page 191
    be cleaned ........ 64 IN-2 O Operator panel 5 Optical Resolution 147 Output resolution 147 P Pad ASY 10 Paper Weight 146 Power consumption 149 Power save mode 33 R Replacement Replacing the Pad ASY 86 Replacing the Pick roller 92 S Scanner installation ......... 17, 18 Scanner Type 146
  • Fujitsu FI 4220C | Operator Manual - Page 192
    Interface 147 Light source 146 Other function 147 Output resolution.......... 147 Paper Weight 146 Scanner type 146 Scanning area 146 Scanning speed 146 Stacker 5 T Turning the power ON 32 U Unlocking the Shipping lock 18 USB interface cable 3, 23 USB interface connector ..........9 W
  • Fujitsu FI 4220C | Operator Manual - Page 193
    IN-4
  • Fujitsu FI 4220C | Operator Manual - Page 194
    fi-4220C Image Scanner Operator's Guide P3PC-E017-01EN Date of issuance : April, 2002 Issuance responsibility : PFU LIMITED Printed in Singapore • Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law. • The contents of
  • Fujitsu FI 4220C | Operator Manual - Page 195
  • Fujitsu FI 4220C | Operator Manual - Page 196
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
Operator's Guide
fi-4220C Image Scanner
P3PC-E017-01EN