Fujitsu FI 5015C Operator's Guide - Page 68

Troubleshooting, Symptom, Check this item, Remedy - power adapter

Get Fujitsu FI 5015C - FB CLR USB 2.0 PERP50PG ADF PDF manuals and user guides
UPC - 097564307713
View all Fujitsu FI 5015C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

4.2 Troubleshooting CAUTION Be careful, the inside of ADF (automatic document feeder) may become hot during the operation. If a problem occurs, check the following items before contacting the manufacturer's authorized service center. Symptom Check this item Remedy Scanner does not turn on. Scanning does not start. Vertical lines appear in the generated image of the scanned image. The generated image shifts or is distorted. Quality of generated image is unsatisfactory. Is the main switch turned on? Have you pushed the power button? Are the AC cable and AC adapter properly connected to the scanner? Is Windows normally started up? Are the documents loaded correctly on the ADF paper chute? Is the ADF closed completely? Is the USB cable properly connected? Does the Function Number Display indicates an alarm or an error? Does the alarm state remain displayed even after the scanner has been turned off and back on again? Is the glass dirty? Are the documents loaded correctly? Turn the main switch on. Push the power button. Correctly connect the AC cable and the AC adapter. Disconnect the AC cable and the AC adapter from the scanner, then connect them again. If this does not restore the power supply, contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. Push the power button again after completely starting up Windows. Load the document correctly on ADF paper chute. Close the ADF completely. Correctly connect the cable. (When a USB hub is used, check the hub's power supply.) When the Function Number Display indicates an alarm or an error, refer to the Operator's Guide "4.1 Error Indications in the Function Number Display" (page. 52) for removing the alarm or the error. Turn off and on the power button. If this does not eliminate the alarm state, contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider. Clean the glass following the instructions in the Operator's Guide "3. Maintenance". Load the documents correctly. Are the glass or sheet guides (a white location) clean? Clean dirty locations. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
54
4.2
Troubleshooting
If a problem occurs, check the following items before contacting the manufacturer's authorized ser-
vice center.
Be careful, the inside of ADF (automatic document
feeder) may become hot during the operation.
Symptom
Check this item
Remedy
Scanner does not turn
on.
Is the main switch turned on?
Turn the main switch on.
Have you pushed the power button?
Push the power button.
Are the AC cable and AC adapter
properly connected to the scanner?
Correctly connect the AC cable and
the AC adapter.
Disconnect the AC cable and the AC
adapter from the scanner, then con-
nect them again.
If this does not restore the power sup-
ply, contact the store where you pur-
chased the scanner or an authorized
FUJITSU scanner service provider.
Is Windows normally started up?
Push the power button again after
completely starting up Windows.
Scanning does not
start.
Are the documents loaded correctly
on the ADF paper chute?
Load the document correctly on ADF
paper chute.
Is the ADF closed completely?
Close the ADF completely.
Is the USB cable properly con-
nected?
Correctly connect the cable. (When a
USB hub is used, check the hub's
power supply.)
Does the Function Number Display
indicates an alarm or an error?
When the Function Number Display
indicates an alarm or an error, refer to
the Operator’s Guide "4.1 Error Indi-
cations in the Function Number Dis-
play" (page. 52) for removing the
alarm or the error.
Does the alarm state remain dis-
played even after the scanner has
been turned off and back on again?
Turn off and on the power button.
If this does not eliminate the alarm
state, contact the store where you pur-
chased the scanner or an authorized
FUJITSU scanner service provider.
Vertical lines appear in
the generated image of
the scanned image.
Is the glass dirty?
Clean the glass following the instruc-
tions in the
Operator's Guide "3.
Maintenance".
The generated image
shifts or is distorted.
Are the documents loaded correctly?
Load the documents correctly.
Quality of generated
image is unsatisfac-
tory.
Are the glass or sheet guides (a
white location) clean?
Clean dirty locations.