Home » GE Manuals » Home Security » GE 60-774 » Manual Viewer

GE 60-774 Installation Instructions - Page 5

Installing a Cover Tamper Switch, Setting the Module Unit Numbers - alarm panel

UPC - 046188091768

Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Installing a Cover Tamper Switch Installing a Cover Tamper Switch Setting the Module Unit Numbers If you are mounting the module in its own plastic and not mounting it inside a cabinet, you need to add cover tamper detection. To do this, install a UL listed 1/4-inch press-fit reed switch on the module back-plate and wire the switch to one of the module zone input terminals or unused panel zone input terminals. Once programmed, if someone opens the module cover, the tamper switch opens and causes an alarm. The reed switch holder and magnet clip are located at the bottom of the back-plate (see Figure 3 for details). To install the tamper reed switch (Figure 9): 1. Slide the reed switch into the reed switch holder located on the module back-plate shown in Figure 9. 2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module back-plate and press the magnet clip down over the magnet until it clicks into place (Figure 9). 3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the module ZONE 1 (1) and ZONE COMMON (2) terminals as shown in Figure 8. The resistor should be located at the reed switch inside the module housing. MODULE BACK-PLATE MODULE COVER MAGNET TO ANY ZONE INPUT MAGNET CLIP REED SWITCH 2.0K OHM EOL RESISTOR (49-467) 9712G12A.DSF Figure 9. Installing the Reed Switch On Concord (software versions 1.0-1.6) and UltraGard Panels Locate the DIP switches on the module circuit board (Figure 1) and set switch 1 to "M" (on - for manual) (Figure 10). Set the remaining switches for the desired unit number. ÁIG"42 Do not change DIP switch settings once the panel is powered up. - UNIT NUMBER 0-7 for UltraGard - UNIT NUMBER 0-15 for Concord UNIT NUMBER 0 UNIT NUMBER 1 UNIT NUMBER 2 M ON M ON M ON A A A 1 234567 8 1 234567 8 1 234567 8 UNIT NUMBER 3 UNIT NUMBER 4 UNIT NUMBER 5 M ON M ON M ON A A A 1 234567 8 1 234567 8 1 234567 8 UNIT NUMBER 6 UNIT NUMBER 7 UNIT NUMBER 8 M ON M ON M ON A A A 1 234567 8 1 234567 8 1 234567 8 UNIT NUMBER 9 UNIT NUMBER 10 UNIT NUMBER 11 M ON M ON M ON A A A 1 234567 8 1 234567 8 1 234567 8 UNIT NUMBER 12 UNIT NUMBER 13 UNIT NUMBER 14 M ON M ON M ON A A A 1 234567 8 1 234567 8 1 234567 8 UNIT NUMBER 15--Do not use in Concord RF systems. M ON A 1 234567 8 9712G09A.DSF Figure 10. Module Unit Number DIP Switch Settings (Non-SuperBus 2000 panels) On Concord (software versions 2.0 or later) and Advent Panels Locate the DIP switches on the module circuit board (Figure 1) and set all switches to "A" (off - for automatic). The unit number will be automatically set when powering up the system. 5

Section	Page
Product Summary	1
SuperBus 2000 vs. SuperBus	1
Module Components	1
Figure 1. Module Circuit Board Components	1
Table 1. Module Component Descriptions	1
Component	1
Function	1
Installation Guidelines	2
Table 2. Maximum Bus Devices Per Panel	2
Panel	2
Maximum Bus Devices	2
Table 3: Maximum Wire Lengths	2
Panel	2
Maximum Wire Length	2
Tools and Supplies Needed	2
Installation	2
Mounting the Module	2
To Mount the Module on a Wall	2
1. Remove the module cover and set it aside (Figure 2).	2
Figure 2. Removing the Cover	2
2. Place the back-plate on the wall and mark the three mounting holes (Figure 3).	2
3. Drill holes and insert appropriate anchors.	2
4. Secure the back-plate to the wall with included screws.	2
Figure 3. Wall Mounting Hole Locations	3
To Mount the Module in an Advent Cabinet	3
1. Remove AC panel power and disconnect the backup battery(s).	3
2. Remove the module cover and set it aside (Figure 2).	3
3. Turn the module upside down and line up the holes on the back-plate at the desired location (F...	3
4. Secure the back-plate to the cabinet using three 1/4 - inch #6-32 self-tapping screws (not inc...	3
Figure 4. Mounting the Module in an Advent Cabinet	3
To Mount the Module in a Concord Cabinet	3
1. Remove AC panel power and disconnect the backup battery.	3
2. Remove and discard the module cover (Figure 2).	3
3. Insert a support standoff shown in Figure 5 (supplied with panel) into the panel circuit board.	3
Figure 5. Support Standoff	3
4. Slide the module back-plate onto the two clips located on the top-left corner or center of the...	3
5. Push the lower-right corner of the module onto the support standoff (see detail in Figure 6).	3
6. Gently press the module up and onto the cabinet side tab.	3
Figure 6. Mounting the Module in a Concord Cabinet	3
Wiring the Module	4
To Wire the Module to a Panel	4
1. Make sure the panel AC power is turned off or removed, and the panel backup battery(s) are dis...	4
2. Wire the module to the panel as shown in Figure 7 and explained in Table 4.	4
Figure 7. General Module Wiring	4
Table 4. SuperBus Module/Panel Wiring	4
Module	4
Terminals	4
Advent*	4
Ultra-	4
Gard	4
Concord	4
To Wire Detectors to the Module	4
Table 5. Zone Input Wire Runs	4
Gauge	4
Max. Wire Run*	4
1. Figure 8 shows an example of how to connect up to eight normally closed (N/C) or normally open...	4
Figure 8. Connecting N/C and N/O Intrusion Circuits to the Module	4
Installing a Cover Tamper Switch	5
To install the tamper reed switch (Figure 9):	5
1. Slide the reed switch into the reed switch holder located on the module back-plate shown in Fi...	5
2. Insert the magnet into the nibs on the module cover. Remove the magnet clip from the module ba...	5
3. Connect the normally closed reed switch (in series with a 2.0K ohm EOL resistor) to the module...	5
Figure 9. Installing the Reed Switch	5
Setting the Module Unit Numbers	5
On Concord (software versions 1.0–1.6) and UltraGard Panels	5
Figure 10. Module Unit Number DIP Switch Settings (Non-SuperBus 2000 panels)	5
On Concord (software versions 2.0 or later) and Advent Panels	5
Power Up and Bus Communication	6
On Concord and Advent Panels	6
New Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Both the green and red LEDs will turn on for one second. The green POWER LED will remain on an...	6
Existing Installations	6
1. Verify that all wiring between the panel and module is correct.	6
2. Connect the panel backup battery(s) and restore panel AC power. Alphanumeric touchpad displays...	6
3. Press 8 for System Menu.	6
4. Press 0 for Program Menu.	6
5. Enter your Install Code (default 0123).	6
6. Enter Item Number 48001 to add SuperBus devices. All installed devices are automatically added...	6
7. Press * twice to return to the Main Menu.	6
8. Both the green and red LEDs turn on for one second. The green POWER LED will remain on and the...	6
On UltraGard Panels	6
1. Verify that all wiring between the panel and module is correct.	6
2. Verify nonconflicting bus device unit number settings.	6
3. Connect the panel backup battery and restore panel AC power.	6
4. Turn on the panel AC power.	6
5. Set the UltraGard panel RUN/PROGRAM switch to PROGRAM.	6
Programming and Testing	7
Troubleshooting	7
Table 6. Troubleshooting	7
Problem	7
Action/Solution	7
1. Check for incorrect wiring connections.	7
2. Make sure panel AC power is applied and the backup battery(s) are connected.	7
3. If the LED still remains off, replace the module.	7
1. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
2. Check for incorrect wiring connections.	7
3. For Concord (software versions 1.0–1.6) and UltraGard panels make sure that module DIP switch ...	7
4. If the LED still doesn’t flash, replace the module.	7
1. For Concord (software versions 1.0–1.6) or UltraGard systems, check for bus devices with the s...	7
2. Re-initialize the panel by disconnecting and reconnecting panel power.	7
3. Make sure the zone has been “learned” into panel memory.	7
4. Verify that the panel recognizes the module by entering program mode (see specific panel Insta...	7
5. Remove zones and try installing the module without the zones.	7
6. Replace the module.	7
Specifications	7

Match case Limit results 1 per page

Installing a Cover Tamper Switch

If you are mounting the module in its own plastic and not

mounting it inside a cabinet, you need to add cover tamper

detection.

To do this, install a UL listed 1/4-inch press-fit reed switch

on the module back-plate and wire the switch to one of the

module zone input terminals or unused panel zone input ter-

minals. Once programmed, if someone opens the module

cover, the tamper switch opens and causes an alarm.

The reed switch holder and magnet clip are located at the

bottom of the back-plate (see Figure 3 for details).

To install the tamper reed switch (Figure 9):

Slide the reed switch into the reed switch holder

located on the module back-plate shown in Figure 9.

Insert the magnet into the nibs on the module cover.

Remove the magnet clip from the module back-plate

and press the magnet clip down over the magnet until it

clicks into place (Figure 9).

Connect the normally closed reed switch (in series with

a 2.0K ohm EOL resistor) to the module ZONE 1 (1)

and ZONE COMMON (2) terminals as shown in Fig-

ure 8. The resistor should be located at the reed switch

inside the module housing.

Figure 9.

Installing the Reed Switch

Setting the Module Unit Numbers

On Concord (software versions 1.0–1.6) and

UltraGard Panels

Locate the DIP switches on the module circuit board (Fig-

ure 1) and set switch 1 to “M” (on - for manual) (Figure 10).

Set the remaining switches for the desired unit number.

Do not change DIP switch settings once the panel is

powered up.

- UNIT NUMBER 0–7 for UltraGard

- UNIT NUMBER 0–15 for Concord

Figure 10.

Module Unit Number DIP Switch Settings

(Non-SuperBus 2000 panels)

On Concord (software versions 2.0 or later) and

Advent Panels

Locate the DIP switches on the module circuit board (Fig-

ure 1) and set all switches to “A” (off - for automatic). The

unit number will be automatically set when powering up the

system.

9712G12A.DSF

MODULE

BACK-PLATE

MODULE

COVER

REED

SWITCH

MAGNET

CLIP

MAGNET

TO ANY ZONE

INPUT

2.0K OHM EOL

RESISTOR (49-467)

9712G09A.DSF

UNIT NUMBER 0

12345678

UNIT NUMBER 1

12345678

UNIT NUMBER 2

12345678

UNIT NUMBER 3

12345678

UNIT NUMBER 4

12345678

UNIT NUMBER 5

12345678

UNIT NUMBER 6

12345678

UNIT NUMBER 7

12345678

UNIT NUMBER 8

12345678

UNIT NUMBER 9

12345678

UNIT NUMBER 10

12345678

UNIT NUMBER 11

12345678

UNIT NUMBER 12

12345678

UNIT NUMBER 13

12345678

UNIT NUMBER 14

12345678

UNIT NUMBER 15--Do not use in Concord RF systems.