GE PEB2060SMSS Installation Instructions
GE PEB2060SMSS - Countertop Microwave Oven Manual
 |
UPC - 084691164166
View all GE PEB2060SMSS manuals
Add to My Manuals
Save this manual to your list of manuals |
GE PEB2060SMSS manual content summary:
- GE PEB2060SMSS | Installation Instructions - Page 1
- Keep these instructions for future reference. • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. • This kit is UL listed for installation alone or over any GE/GE Profile single electric wall oven. Not - GE PEB2060SMSS | Installation Instructions - Page 2
of the cutout. On 30″ models, allow 11⁄8″ at the top, 21⁄16″ on the sides and 11⁄4″ at the bottom for overlap of the Trim Frame over the edges of the cutout. FOR INSTALLATION ABOVE A BUILT-IN OVEN: Microwave oven should be installed on a 3/8″ plywood base and supported by 2x4 or 1x2 equivalent - GE PEB2060SMSS | Installation Instructions - Page 3
the microwave oven, including the turntable and turntable support. Carefully turn the microwave upside down. D Install bottom microwave oven before the ducts are attached. Upper Duct 3 Holes 3 Tabs ❒ 5 INSTALL MICROWAVE OVEN INTO CABINET A Slide the microwave oven part way into the cabinet opening - GE PEB2060SMSS | Installation Instructions - Page 4
A Your trim kit is now fully installed. Replace the turntable and turntable support that were removed from the inside of the microwave oven. B Keep these installation instructions and extra screws for future reference and need. Do not place them in the microwave oven. C Replace house fuse or close
-
1 -
2 -
3 -
4
 |
 |
PART
QUANTITY
❒
Trim Frame
1
❒
Bottom Duct
1
❒
Side Duct
1
❒
4 mm x 12 mm
23
Round-Head Screws
(21 required
for installation)
❒
4 mm x 14 mm
6
Flat-Head Screws
(4 required for
installation)
❒
Anti-Tip Brace
1
❒
Anti-Tip Bracket
1
❒
Upper Duct
1
❒
Top Bracket
1
❒
Bottom Bracket
1
❒
Templates
2
PARTS INCLUDED
Questions? Call 800.GE.CARES (800.432.2737)
or
Visit our Website at:
ge.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
.
Installation
Built-In Trim Kits
Instructions
JX2027 and JX2030
Read these instructions completely and carefully.
•
IMPORTANT –
Save these instructions for local
inspector’s use.
•
IMPORTANT –
Observe all governing codes and
ordinances.
•
Note to Installer –
Be sure to leave these instructions with the
Consumer.
•
Note to Consumer –
Keep these instructions for future reference.
•
For easier installation and personal safety, we recommend that two people
install this microwave oven.
WARNING
—
This oven must be plugged into a properly
grounded 3-hole, 120V receptacle as required by the National Electrical Code.
❒
BEFORE YOU BEGIN
•
Do not alter or modify any part of this kit or the oven.
•
Unplug the microwave oven before attempting installation of this kit.
•
Skill level
– Installation of this appliance requires basic mechanical and
electrical skills.
•
Completion time
– 1-3 hours
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not covered under the Warranty.
•
This kit is UL listed for installation alone or over any GE/GE Profile
single electric wall oven. Not for use adjacent to (within 2 feet of) any gas
or electric range, cooktop or oven.
•
This kit is for use on models: PEB2060DMBB, PEB2060DMWW,
PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,
JEB1860DMCC and JEB1860SMSS.
TOOLS YOU WILL NEED
❒
Phillips screwdriver
❒
Pencil
❒
Tape measure
❒
Awl or punch
❒
Drill with
7
/
64
″
bit or #35
FOR YOUR SAFETY:
WARNING –
Before beginning the
installation, switch power off at service panel and lock
the service disconnecting means to prevent power
from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.
❒
Level
❒
Scissors (optional)
1
NOTE:
This kit has extra screws to prevent the technician from spending extra
time locating a replacement screw in case they lose one during installation.