GE PNM1871SMSS Installation Instructions - Page 17

ADAPTING MICROWAVE, BLOWER FOR OUTSIDE, BACK EXHAUST cont., NOTE: The blower unit exhaust

Page 17 highlights

Installation Instructions B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.) 3 Rotate blower unit counterclockwise 180°. Before Rotation After Rotation 6 Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back End A End B Back of Microwave Back of Microwave 4 Gently remove the wires from the grooves. Reroute the wires through grooves on other side of the blower unit. Before Rerouting After Rerouting Wires Routed Through Right Side Wires Routed Through Left Side 5 Roll the blower unit 90° so that fan blade openings are facing out the back of the microwave. Before Rolling After Rolling CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 7 Secure the blower unit to the microwave with the screw from Step 1. Blower Plate Back of Microwave Blower Motor Screw 8 Replace the blower plate in the same position as before with the screw. 9 Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven. Back of Microwave Back of Microwave Adaptor Back of Microwave Guide Guide Locking Tabs Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

Attach the exhaust adaptor to the rear of the
oven by sliding it into the guides at the top
center of the back of the oven.
AFTER: Fan Blade
Openings Facing Back
6
Place the blower unit back into the opening.
8
Replace the blower plate in the same position
as before with the screw.
7
Roll the blower unit 90° so that fan blade
openings are facing out the back of the
microwave.
5
4
3
ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
BACK EXHAUST (cont.)
B5.
17
Rotate blower unit counterclockwise 180°.
Before Rotation
After Rotation
Gently remove the wires from the grooves.
Reroute the wires through grooves on other side
of the blower unit.
Before Rerouting
After Rerouting
Wires Routed Through Right Side
Wires Routed Through Left Side
Back of
Microwave
Back of
Microwave
Blower Plate
Blower Motor
Screw
Secure the blower unit to the microwave with
the screw from Step 1.
Before Rolling
After Rolling
Back of
Microwave
End A
End B
Back of
Microwave
Back of
Microwave
9
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not
pinched.
NOTE: The blower unit exhaust
openings should match exhaust
openings on rear of microwave oven.
Installation Instructions
Push in securely until it is in the lower locking
tabs. Take care to assure that the damper hinge
is installed so that it is at the top and that the
damper swings freely.
Guide
Guide
Adaptor
Locking Tabs
Back of
Microwave