GE PVM9005EJES Installation Instructions - Page 14

Warning

Get GE PVM9005EJES PDF manuals and user guides View all GE PVM9005EJES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Installation Instructions A3 ADJUST BLOWER MOTOR 1 Remove the screws holding the blower unit and the screws securing the blower plate. Remove the blower plate from the outer case by sliding it toward the back of the microwave and pulling up. Blower Motor Screws Blower Plate A3 $'-867%/2:(502725 FRQW Fan Blades Wires Back of Mircrowave 3 Roll the blower so that fan blade openings are facing the top of the oven. Place the blower back into the opening. Rotate 90° Blower Motor Screw 2 Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. Back of Mircrowave Note: Make sure the wires remain routed through the openings in the motor frame. To avoid damage to the fan motor wiring, insert motor carefully such that the fan motor wiring does not contact the microwave power cord bracket. WARNING: 5LVNRI(OHFWULF6KRFN Can cause injury or death. Do not pull or stretch the EORZHUXQLWZLULQJ0DNHVXUHWKHZLUHVDUHQRW pinched. 4 Slide the blower plate back onto the microwave by placing the side tabs into the slots and pushing gently until the back tab is seated into the rear slot. Replace 3 screws. Side Tab Side Slot Rear Tab Rear Slot 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Installation Instructions
14
ADJUST BLOWER MOTOR
A3
Remove the screws holding the blower unit and
the screws securing the blower plate. Remove
the blower plate from the outer case by sliding it
toward the back of the microwave and pulling up.
1
Blower Plate
Blower Motor Screws
Blower
Motor
Screw
2
Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the
blower unit.
A3
Roll the blower so that fan blade openings are
facing the top of the oven. Place the blower back
into the opening.
Slide the blower plate back onto the microwave
by placing the side tabs into the slots and pushing
gently until the back tab is seated into the rear slot.
Replace 3 screws.
Note:
Make sure the wires remain routed through the
openings in the motor frame. To avoid damage to
the fan motor wiring, insert motor carefully such that
the fan motor wiring does not contact the microwave
power cord bracket.
3
4
Back of
Mircrowave
Rotate 90°
WARNING:
Can cause injury or death. Do not pull or stretch the
pinched.
Side Tab
Side Slot
Rear Slot
Rear Tab
Back of
Mircrowave
Fan Blades
Wires