Graco 1757816 Owners Manual - Page 65

Using LATCH to install Base

Get Graco 1757816 - Passage Travel System Lowery PDF manuals and user guides
UPC - 047406106028
View all Graco 1757816 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

6.4 Using LATCH to install Base 1. For ease of installation, extend LATCH to its maximum length. 2. Position base in vehicle seat as shown. 3. Thread LATCH through base belt path normally used for vehicle seat belt. Make sure that LATCH is UNDER tongue on base ˜. Belt must lay flat and not be twisted. 4. Hook Connectors to vehicle lower anchors. Pull firmly on Connectors to be sure they are attached ™. 5. Tighten LATCH by pushing down hard on base and pulling the adjustment belt š. 6. NEVER put two LATCH connectors on one vehicle LATCH anchor unless specifically allowed by the vehicle manufacturer ›. Tongue ˜ ™ š › 7. Test infant restraint for secure installation as described in infant restraint "Final Safety Check" p.36. 8. Check that the LATCH stays tight and does not slip from the tightened position. If it does not stay tight, try another seating position or contact Customer Service. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
33
1.
For ease of installation, extend
LATCH
to its maximum length.
2.
Position base in vehicle seat as
shown.
3.
Thread
LATCH
through base belt
path normally used for vehicle seat
belt. Make sure that
LATCH
is
UNDER
tongue on base
➌
.
Belt must lay flat and not be twisted.
4.
Hook
Connectors
to vehicle lower
anchors. Pull firmly on
Connectors
to
be sure they are attached
➍
.
5.
Tighten
LATCH
by pushing down
hard on base and pulling the
adjustment belt
➎
.
6.
NEVER
put two
LATCH
connectors on
one vehicle
LATCH
anchor unless
specifically allowed by the vehicle
manufacturer
➏
.
7.
Test infant restraint for secure
installation as described in infant
restraint
“Final Safety Check” p.36
.
8.
Check that the
LATCH
stays tight and does not slip from the
tightened position. If it does not stay tight, try another
seating position or contact Customer Service.
6.4 Using LATCH to install Base
➌
➎
Tongue
➏
➍