Haier HMV1630DBBB HMV1630 Installation Guide

Haier HMV1630DBBB Manual

Haier HMV1630DBBB manual content summary:

  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 1
    Over the Range Microwave Oven Installation Installation du Four À Micro-Ondes À Hotte Intégrée Instalación del Horno Microondas Part # MW-7777-01 Installation Manual Model # HM1630 Manual del Usuario Para Modelo de # HM1630 Guide de l'Utilisateur Modéle# HM1630 Quality t Innovation t Style
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 2
    MICROWAVE OVEN INSTALLATION INSTRUCTIONS WHAT DO I NEED TO HAVE TO INSTALL THE MICROWAVE OVEN?.........7-8 Parts Included 7 Tools You Will Need 8 Mounting Space 8 WHAT DO I NEED TO DO BEFORE I INSTALL THE MICROWAVE OVEN? .9-11 PLACEMENT OF THE MOUNTING PLATE 9-11 Removing the Mounting Plate
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 3
    will guide you in getting the best performance from your Haier Microwave Oven. Model number Remember to record the model and serial number. They are on a label in the Microwave Oven. Serial number Date of purchase Staple your receipt to your manual. You will need it to obtain warranty service. 2
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 4
    to a separate 15 to 20 ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code. 3
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 5
    : READ AND SAVE THESE INSTRUCTIONS Doing so will: tNBLFJOTUBMMBUJPOFBTJFS tIFMQZPVJOUIFGVUVSFJGZPVIBWFRVFTUJPOT tIFMQJGZPVIBWFBOFMFDUSJDBMJOTQFDUJPO Call your dealer when you have questions or need service. When you call, you will need the microwave model and serial numbers
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 6
    to allow free movement of the damper. OUTSIDE BACK EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. DUCT PIECES Wall Cap EQUIVALENT NUMBER EQUIVALENT LENGTH X USED = LENGTH 40 Ft. (12.2m) x (1) = 40 Ft. (12.2m) 3 Ft. Straight Duct (31
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 7
    exceed 120 equivalent feet (36.5 m). Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages. Also
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 8
    (plastic) You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts. NOTE: Some extra parts are included. REAR WALL TEMPLATE ININSTSRTAULCLATITOIONNS Rear Wall 1 Template Installation 1 Instructions Separately 2 Packed Grease Filters
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 9
    (used on recessed bottom cabinet installations only) Saw (saber, hole or keyhole) Stud finder or Hammer (optional) Safety goggles Level Duct and masking tape MOUNTING SPACE Bottom Edge of Cabinet CFDBSFGVMUP follow the instructions on the top cabinet template for power cord clearance. 8
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 10
    English 1. PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1. Remove the installation instructions, filters, glass tray and the small hardware bag. Do Carton not remove the Styrofoam protecting the front of the oven. 2. Fold back
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 11
    bottom is level. If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang depth. This will keep the microwave level. 1. Measure the inside depth of the front overhang. 2. Draw a horizontal line on the back wall
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 12
    E and draw a fifth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside. 4. Drill holes on the circles. If there is a stud, drill a 3⁄16" hole for wood screws. For holes that don
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 13
    microwave NOTE: This microwave is shipped assembled for Recirculating. Select the type of ventilation required for your installation RECIRCULATING (NON-VENTED DUCTLESS) On models shipped for recirculating exhaust, a disposable charcoal filter is factory installed to help remove smoke and odors.
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 14
    English A. OUTSIDE TOP EXHAUST (VERTICAL DUCT) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Adapting Microwave Blower for Outside Top Exhaust A4. Check Damper Operation A5. Mount Microwave Oven A6. Adjust Exhaust Adaptor A7. Connect Ductwork IMPORTANT NOTES:
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 15
    PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through that holds the blower plate to the microwave. Remove and save the screw holding the blower motor to the microwave. Blower Plate Back of Microwave Blower Moto Screw 2.
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 16
    that the damper hinge is installed so that the damper swings freely. Adaptor Guide Back of Microwave Locking Tab A4. CHECK FOR PROPER DAMPER OPERATION t.BLFTVSFUBQFTFDVSJOHEBNQFSJT removed and damper pivots easily before mounting microwave. Blower Plate Exhaust Adaptor t:PVXJMMOFFE
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 17
    two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) 8. Install grease filters. See the Owner's Manual packed with the microwave. A6. ADJUST THE EXHAUST ADAPTOR Blower Plate Open the top cabinet and adjust the
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 18
    INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Remove Blower Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Microwave an opening in the rear wall for outside exhaust. t Read the instructions on the REAR WALL TEMPLATE. t Tape it to the rear wall,
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 19
    Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through. t Read the instructions on the TOP CABINET TEMPLATE
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 20
    End B properly secured. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 8. Secure the blower unit to the microwave with the original screw. 9. Replace the blower plate in the same position as before with the screw. Make sure the screw is tight. 19
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 21
    damper swings freely. Adaptor Back of Microwave Guide Guide Locking Tabs B6. MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 22
    on each screw. 6. Tighten center screw completely. 7. Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) 8. Install grease filters. See the Owner's Manual packed with the microwave. 5 6 21
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 23
    (NON-VENTED DUCTLESS) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Blower Plate C4. Mount the Microwave Oven C5. Install or change Charcoal Filter IMPORTANT NOTES: t Make sure the screws for the blower motor and blower plate are securely tightened when
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 24
    Check to see that the blower plate is correctly installed on the unit. C4. MOUNT THE MICROWAVE OVEN Blower Plate FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 25
    the cord, especially when mounting flush to bottom of cabinet. 4. Attach the microwave oven to the top cabinet microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) 8. Install grease filters. See the Owner's Manual packed with the microwave
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 26
    Votre Four À Micro-Ondes 4 Évacuation De La Hotte 5-6 Dommages - Expédition/Installation 7 INSTRUCTIONS D'INSTALLATION DU FOUR À MICRO-ONDES À HOTTE INTÉGRÉE CE DONT J'AI BESOIN POUR L'INSTALLATION DU FOUR À MICRO-ONDES........7-8 Pièces Comprises 7 Outils Nécessaires 8 Dégagements Pour
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 27
    base, incluant celles qui suivent : 1. Lire toutes les instructions avant l'utilisation de l'appareil. 2. Utiliser le lave-vaisselle seulement barrassez d'un vieux lave-vaisselle. Merci d'utiliser un produit Haier. Ce manuel facile d'utilisation vous guidera pour obtenir une service de garantie. 2
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 28
    doit être aménagée dans l'armoire située au-dessus du four à micro-ondes. La boîte de la prise et le circuit d'alimentation doivent être installés par un électricien qualifié, conformément aux normes du Code national d'électricité ou du code local en vigueur. 3
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 29
    " ou "AVERTISSEMENT". DANGER VOUS RISQUEZ D'ÊTRE GRAVEMENT BLESSÉ SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS IMMÉDIATEMENT. WARNING VOUS RISQUEZ D'ÊTRE GRAVEMENT BLESSÉ SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS. Tous les messages de sécurité vous informeront du danger potentiel, comment réduire les risques
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 30
    de cisailles pour que le registre puisse bouger. ÉVACUATION À L'EXTÉRIEUR PAR L'ARRIÈRE (EXEMPLE SEULEMENT) Le tableau suivant décrit un exemple d'installation de conduit. PIÈCES DE CONDUIT Wall Cap LONGUEUR NOMBRE LONGUEUR ÉQUIVALENTE X UTILISÉ = ÉQUIVALENTE 40 pi (12,2m) x (1) = 40 pi (12
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 31
    . L'évacuation vers l'extérieur requiert un CONDUIT D'ÉVACUATION POUR HOTTE. Lisez attentivement ce qui suit. REMARQUE : Il est important que l'évacuation soit installée enutilisant le chemin le plus direct et avec le moins de coudes possible. Cela assure une bonne évacuation et aide a prévenir les
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 32
    : Des pièces supplémentaires sont incluses. ADDITIONAL PARTS PIÈCE TOP CABINET TEMPLATE REAR WALL TEMPLATE ININSTSRTAULCLATITOIONNS Gabarit pour armoire supérieure Gabarit pour mur arrière Instructions d'installation QUANTITÉ 1 1 1 Filtres à 2 graisses emballés séparément Adaptateur 1 de
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 33
    , si besoin est, pour l'espacement avec l''armoire supérieure (utilisées pour l'installation sous une armoire dont le fond est doté d'un rebord) Lunettes de sécurité lisse et plat, suivez attentivement les instructions du gabarit pour armoire supérieure concernant le dégagement du cordon d'alimentation.
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 34
    DE LA PLAQUE DE MONTAGE A. ENLÈVEMENT DU FOUR À MICRO-ONDES DE LA BOÎTE/ ENLÈVEMENT DE LA PLAQUE DE MONTAGE 1. Retirez les directives d'installation, les filtres, le plateau en verre et le sachet de quincaillerie. Boîte N'enlevez pas la protection en polystyrène du devant du four. 2. Repliez
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 35
    À 30 po (76,2 cm) de la surface de cuisson Vos armoires peuvent être dotées de garnitures décoratives qui entravent l'installation du micro-ondes. Enlevez l'élément décoratif pour installer convenablement le four à micro-ondes et pour vous assurer qu'il est de niveau. LE FOUR À MICRO-ONDES DOIT ÊTRE
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 36
    Français Trou A Encoches de la ligne centrale Tracez une ligne verticale sur le mur à partir du centre de l'armoire supérieure Trou B Trou C Zone E Trou D ATTENTION: Portez des gants pour éviter de vous blesser sur les bords coupants. D. ALIGNEMENT DE LA PLAQUE MURALE 1. Tracez une ligne
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 37
    (sans conduit) REMARQUE : Ce four à micro-ondes est équipé à l'usine en vue d'une Recyclage. Choisissez le type d'évacuation approprié à votre installation et rendez-vous à cette section. A. ÉVACUATION À L'EXTÉRIEUR PAR LE DESSUS (CONDUIT VERTICAL) Adaptateur en place pour une évacuation à l'ext
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 38
    du ventilateur A4. Vérification du fonctionnement du registre A5. Installation du four à micro-ondes A6. Ajustement de l'adaptateur d'é À AILETTES: 3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. REMARQUE : Avant de resserrer
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 39
    Français A2. UTILISATION DU GABARIT POUR ARMOIRE SUPÉRIEURE POUR LA PRÉPARATION DE L'ARMOIRE SUPÉRIEURE Vous devez percer des trous pour les vis de soutien supérieures, ainsi qu'un trou suffisamment grand pour y faire passer le cordon d'alimentation et une ouverture assez grande pour l'adaptateur
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 40
    jusqu'à ce qu'il soit dans les fentes de blocage inférieures. Assurez-vous que la charnière du registre est installée et que le registre bouge librement. Adaptateur Guide Arrière du four à micro-ondes Fentes de blocage A4. VÉRIFICATION DU FONCTIONNEMENT DU REGISTRE t"TTVSF[WPVTRVFMFSVCBOBEI
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 41
    pour le mettre contre le dessous de l'armoire. REMARQUE : Lors de l'installation du four à microondes, faites passer le cordon d'alimentation à travers le serré. Faites attention de ne pas le coincer, particulièrement au moment d'installer le four sous l'armoire. 1 Avant de l'armoire Étagère infé
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 42
    VACUATION À L'EXTÉRIEUR PAR L'ARRIÈRE (CONDUIT HORIZONTAL) VUE D'ENSEMBLE DE L'INSTALLATION B1. Préparation du mur arrière B2. Enlèvement de l'plaque du dans le mur arrière pour l'évacuation à l'extérieur. t Lisez les instructions figurant sur le GABARIT POUR MUR ARRIÈRE. t Collez-le au mur arri
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 43
    percer des trous pour les vis de soutien supérieures, ainsi qu'un trou suffisamment grand pour y faire passer le cordon d'alimentation. t Lisez les instructions sur le GABARIT POUR ARMOIRE SUPÉRIEURE. t Collez-le sous l'armoire supérieure à l'aide de ruban adhésif. t Percez les trous, en suivant
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 44
    Français B5. ADAPTATION DU VENTILATEUR DU FOUR À MICRO-ONDES POUR L'ÉVACUATION À L'EXTÉRIEUR PAR L'ARRIÈRE 1. Enlevez et conservez la vis qui retient le moteur du ventilateur au four à micro-ondes. Moteur du ventilateur Arrière du four à micro-ondes 2. Enlevez délicatement l'ensemble du
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 45
    et que le registre bouge librement. Adaptateur Arrière du four à micro-ondes Guide Guide Fentes de blocage B6. INSTALLATION DU FOUR À MICRO-ONDES POUR VOTRE SÉCURITÉ ET POUR FACILITER L'INSTALLATION, L'INSTALLATION DE CE FOUR DOIT ÊTRE EFFECTUÉE PAR DEUX PERSONNES. IMPORTANT : Ne saisissez pas
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 46
    pour le mettre contre le dessous de l'armoire. REMARQUE : Lors de l'installation du four à microondes, faites passer le cordon d'alimentation à travers le serré. Faites attention de ne pas le coincer, particulièrement au moment d'installer le four sous l'armoire. 1 Avant de l'armoire Étagère infé
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 47
    de la plaque de montage au mur C2. Préparation de l'armoire supérieure C3. Vérification de l'plaque du ventilateur C4. Installation du four à micro-ondes C5. Installation ou changemeut du filtre à charbon REMARQUES IMPORTANTES : t Assurez-vous que les vis du moteur du ventilateur et de la plaque du
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 48
    suffisamment grand pour y faire passer le cordon d'alimentation. t Lisez les instructions sur le GABARIT POUR ARMOIRE SUPÉRIEURE. t Collez-le sous l'armoire saisissez pas ou n'utilisez pas la poignée du four durant l'installation. REMARQUE: Si vos armoires sont en métal, installez un passefil
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 49
    pour le mettre contre le dessous de l'armoire. REMARQUE : Lors de l'installation du four à microondes, faites passer le cordon d'alimentation à travers le serré. Faites attention de ne pas le coincer, particulièrement au moment d'installer le four sous l'armoire. 1 Avant de l'armoire Étagère infé
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 50
    la porte. 3. Enlevez la grille. Retirez complètement la grille en la tirant en ligne droite. 4. Installez le filtre à charbon. Lorsqu'il est bien installé, le treillis métallique du filtre est visible de l'avant. 5. Réinstallez la grille et les vis. 6. Fermez la porte. Filtre à charbon Insérez le
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 51
    Español CONTENIDOS PAGE PRECAUCIONES DE SEGURIDAD 2 Requisitos eléctricos 3 Antes de utilizar su horno microondas 4 Campana de salida de emanaciones 5-6 Daños durante el envío o la instalación 7 INSTRUCCIONES DE INSTALACIÓN DEL HORNO MICROONDAS SOBRE LA COCINA CON QUÉ DEBO CONTAR PARA INSTALAR
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 52
    ctrico en ninguna circunstancia. No utilice cable de prolongación. Gracias por usar nuestro producto Haier. Este manual fácil de usar le guiará para obtener el mejor rendimiento posible de su horno microondas Haier. Número de modelo Número de serie Recuerde anotar los números de modelo y de serie
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 53
    Español REQUISITOS ELÉCTRICOS La clasificación del producto es 120 voltios de CA, 60 Hertz y 1550 vatios. Este producto debe conectarse en un circuito de suministro con el voltaje y la frecuencia correctos. El tamaño del cable debe cumplir los requerimientos del Código Eléctrico nacional o el código
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 54
    Español ANTES DE UTILIZAR SU HORNO MICROONDA IMPORTANTE: LEA ESTAS INSTRUCCIONES Y CONSÉRVELAS De esta manera: t MBJOTUBMBDJØOTFSÈNÈTGÈDJM t MFBZVEBSÈFOFMGVUVSPTJUJFOFQSFHVOUBT t MFBZVEBSÈTJUJFOFVOBJOTQFDDJØOFMÏDUSJDB Llame a su vendedor cuando tenga preguntas o necesite
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 55
    Español CAMPANA DE SALIDA DE EMANACIONES NOTA: Lea estas páginas a continuación únicamente si planifica realizar la salida de emanaciones hacia el exterior. Si tiene pensado recircular el aire nuevamente en la habitación, siga en la página 7. SALIDA SUPERIOR DE EMANACIONES HACIA EL EXTERIOR (SOLO
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 56
    necesario un CONDUCTO PARA LA CAMPANA DE SALIDA DE EMANACIONES. Lea detenidamente la siguiente información NOTA: Es importante que la ventilación se instale utilizando el camino más directo con la menor cantidad de codos posible. De esta manera se garantiza una apropiada salida de emanaciones y se
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 57
    Español DAÑOS DURANTE EL ENVÍO O LA INSTALACIÓN t Si la unidad resulta dañada durante el envío, devuélvala a la tienda en la que la compró para que le realicen reparaciones o la reemplacen. t Si la unidad fue dañada por el cliente, las reparaciones o el reemplazo son responsabilidad del cliente.
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 58
    cm) min. Zócalo de la encimera 66" (167,6 cm) o más desde el piso hasta la parte superior del microondas NOTAS: t El espacio entre gabinetes debe ser de 30" (76,2 cm) de ancho de los conductos de salida de emanaciones. t Cuando instale el horno microondas debajo de gabinetes lisos y planos,
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 59
    Español 1. UBICACIÓN DE LA PLACA DE MONTAJE A. CÓMO QUITAR EL HORNO MICROONDAS DE LA CAJA/ CÓMO QUITAR LA PLACA DE MONTAJE 1. Retire las instrucciones de instalación, los filtros, la bandeja de vidrio y la bolsa Caja pequeña con piezas complementarias. No quite la espuma de poliestireno que
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 60
    . EL MICROONDAS DEBE ESTAR NIVELADO. Use un nivel para asegurarse de que la parte inferior del gabinete esté nivelada. Si los gabinetes tienen únicamente una saliente frontal, sin marco trasero o lateral, instale la placa de montaje a la misma distancia que la profundidad de la saliente frontal
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 61
    de montaje sobre la pared, asegurándose de que las lengüetas toquen la parte inferior del gabinete o la línea de nivel trazada en el Paso C para los gabinetes con saliente frontal. Alinee la muesca y la línea central de la parte inferior de la placa de montaje con la línea central de la pared. 3.
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 62
    la salida superior de emanaciones hacia el exterior Página 13 B. SALIDA TRASERA HACIA EL EXTERIOR (CONDUCTO HORIZONTAL) El adaptador debe pasarse a la parte de atrás para la salida trasera de emanaciones hacia el exterior Página 17 C. CON RECIRCULACIÓN (SIN VENTILACIÓN, SIN CONDUCTO) En los modelos
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 63
    Antes de ajustar los pernos acodados y el tornillo montaje para madera, asegúrese de que las lengüetas de la placa de montaje toquen la parte inferior del gabinete cuando se las presione a nivel contra la pared y que la placa esté bien centrada debajo del gabinete. PRECAUCIÓN: tenga cuidado de
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 64
    ADAPTAR EL VENTILADOR DEL MICROONDAS PARA LA SALIDA SUPERIOR DE EMANACIONES HACIA EL EXTERIOR 1. Coloque el microondas en posición vertical, con la parte superior de la unidad hacia arriba. Retire el tornillo que sostiene la placa del ventilador en el microondas. Retire y conserve el tornillo que
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 65
    las lengüetas. Tenga cuidado de asegurarse de que la bisagra del regulador de tiro esté instalada así el regulador oscila libremente. Adaptador Guía Parte trasera Lengüeta de cierre A4. CONTROL DEL FUNCIONAMIENTO CORRECTO DEL REGULADOR DE TIRO t"TFHÞSFTFEFRVFMBDJOUBRVFBTFHVSB el regulador
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 66
    arriba contra la NOTE: When mounting the microwave oven, thread power cord through hole parte superior del horno microondas. (Mientras ajuste los tornillos, sostenga el horno microondas en su lugar contra la pared y el gabinete superior.) 8. Instale los filtros para la grasa. Consulte el manual
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 67
    estén apretados. B1. PREPARACIÓN DE LA PARED TRASERA PARA LA SALIDA TRASERA DE EMANACIONES HACIA EL EXTERIOR Debe cortar una abertura en la parte posterior de la pared para la salida exterior de emanaciones. t Lea las instrucciones de la PLANTILLA PARA LA PARED POSTERIOR. t Péguela a la pared
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 68
    NOTA: Antes de ajustar los pernos acodados y el tornillo para madera, asegúrese de que las lengüetas de la placa de montaje toquen la parte inferior del gabinete cuando se las presione a nivel contra la pared y que la placa esté bien centrada debajo del gabinete. PRECAUCIÓN: Tenga cuidado de evitar
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 69
    90º así las aberturas de la paleta del ventilador miran hacia la parte de atrás del microondas. Antes de redirigir Después de redirigir Antes de Cables dirigidos por el lado derecho Cables dirigidos por el lado izquierdo Parte trasera del microondas 7. Coloque la unidad del ventilador de nuevo
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 70
    ajustar los tornillos en demasía. energía para evitar que se corte el cable. 1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 71
    . 7. Ajuste los dos tornillos exteriores a la parte superior del horno microondas. (Mientras ajuste los tornillos, sostenga el horno microondas en su lugar contra la pared y el gabinete superior). 8. Instale los filtros para la grasa. Consulte el manual del usuario embalado junto con el microondas
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 72
    superior C3. Controle la placa del ventilador C4. Acomode el horno microondas C5. Instale o cambie el filtro de carbón NOTAS IMPORTANTES: t Asegúrese de que los rese de que las lengüetas de la placa de montaje toquen la parte inferior del gabinete cuando se las presione a nivel contra la pared y
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 73
    gabinete superior. t Realice los agujeros siguiendo las instrucciones de la PLANTILLA DEL GABINETE SUPERIOR. PRECAUCIÓN: Use anteojos de protección cuando realice agujeros en la parte inferior del gabinete C3. CONTROLE LA PLACA DEL VENTILADOR t Coloque el microondas en posición vertical, con la
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 74
    lugar contra la pared y el gabinete superior.) 8. Instale los filtros para la grasa. Consulte el manual del usuario embalado junto con el microondas. NOTA: Cuando acomode el horno microondas, pase el cable de energía por el agujero en la parte inferior del gabinete superior. Manténgalo firme durante
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 75
    con ventilación a funcionamiento con recirculación. 1. Retire los tornillos de la parte superior de la parrilla con un destornillador Phillips n.º1 2. Abra la puerta. 3. Retire la parrilla. Jale de la parrilla en línea recta. 4. Instale el filtro de carbón. Cuando está bien instalado, la tela met
  • Haier HMV1630DBBB | HMV1630 Installation Guide - Page 76
    le service des consommateurs 'Haier Customer Satisfaction Center' au 1-877-337-3639. UNE PREUVE D'ACHAT DATEE EST REQUISE POUR BENEFICIER DE LA GARANTIE. Made in China Fabriqué en Chine Hecho en China Haier America New York, NY 10018 Printed in China Issued June 2010 Microwave Oven Installation
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76

Over the Range Microwave Oven Installation
Installation du Four À Micro-Ondes
À Hotte Intégrée
Instalación del Horno Microondas
Quality Innovation Style
Installation Manual
Model # HM1630
Manual del Usuario
Para Modelo de # HM1630
Guide de l’Utilisateur
Modéle# HM1630
Part # MW-7777-01