Harman Kardon AVR 110 Owners Manual - Page 15

System and Power Connections - remote control

Get Harman Kardon AVR 110 PDF manuals and user guides View all Harman Kardon AVR 110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installation and Connections VIDEO CONNECTION NOTE: Composite and S-Video signals may only be viewed in their native formats. S-Video inputs may only be viewed when the AVR 110 is connected to a TV set or video display with S-Video capability. System and Power Connections Remote Control Extension If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, an optional remote sensor may be used. Connect the output of the remote sensor to the Remote IR Input jack a. If other components are also prevented from receiving remote commands, only one sensor is needed. Simply use this unit's sensor or a remote eye by running a connection from the Remote IR Output jack · to the Remote IR Input jack on Harman Kardon or other compatible equipment. IMPORTANT NOTE: Any cables run inside walls should be CL3/FT4 rated, or carry any other certification that is required by the NEC or state and local building and electrical codes. To avoid interference, audio and speaker cables should not be parallel to, or run in the same conduits or path with, AC cables. If you have any questions about multiroom wiring, consult your dealer, custom installer or low-voltage electrical contractor. AC Power Connections This unit is equipped with two accessory AC outlets. They may be used to power accessory devices, but they should not be used with highcurrent draw equipment such as power amplifiers. The total power draw to each outlet may not exceed 100 watts. The Switched AC Accessory outlet fl will receive power only when the unit is on. This is recommended for devices that have no power switch or a mechanical power switch that may be left in the "ON" position. NOTE: Many audio and video products go into a Standby mode when they are used with switched outlets, and cannot be fully turned on using the outlet alone without a remote control command. The Unswitched AC Accessory outlet ‡ will receive power as long as the unit is plugged into a powered AC outlet. Finally, when all connections are complete, plug the power cord into a nonswitched 110-volt AC wall outlet. You're almost ready to enjoy the AVR 110! 15 INSTALLATION AND CONNECTIONS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
15
INSTALLATION AND CONNECTIONS
Installation and Connections
VIDEO CONNECTION NOTE:
Composite and
S-Video signals may only be viewed in their
native formats. S-Video inputs may only be
viewed when the AVR 110 is connected to a TV
set or video display with S-Video capability.
System and Power Connections
Remote Control Extension
If the receiver is placed behind a solid or
smoked glass cabinet door, the obstruction may
prevent the remote sensor from receiving com-
mands. In this event, an optional remote sensor
may be used. Connect the output of the remote
sensor to the
Remote IR Input
jack
a
.
If other components are also prevented from
receiving remote commands, only one sensor is
needed. Simply use this unit
’
s sensor or a
remote eye by running a connection from the
Remote IR Output
jack
·
to the Remote
IR Input jack on Harman Kardon or other com-
patible equipment.
IMPORTANT NOTE:
Any cables run inside walls
should be CL3/FT4 rated, or carry any other certi-
fication that is required by the NEC or state and
local building and electrical codes. To avoid inter-
ference, audio and speaker cables should not be
parallel to, or run in the same conduits or path
with, AC cables. If you have any questions about
multiroom wiring, consult your dealer, custom
installer or low-voltage electrical contractor.
AC Power Connections
This unit is equipped with two accessory AC
outlets. They may be used to power accessory
devices, but they should not be used with high-
current draw equipment such as power ampli-
fiers. The total power draw to each outlet may
not exceed 100 watts.
The
Switched AC Accessory
outlet
fl
will
receive power only when the unit is on. This is
recommended for devices that have no power
switch or a mechanical power switch that may
be left in the
“
ON
”
position.
NOTE:
Many audio and video products go into
a Standby mode when they are used with
switched outlets, and cannot be fully turned on
using the outlet alone without a remote control
command.
The
Unswitched AC Accessory
outlet
‡
will
receive power as long as the unit is plugged
into a powered AC outlet.
Finally, when all connections are complete, plug
the power cord into a nonswitched 110-volt AC
wall outlet. You
’
re almost ready to enjoy the
AVR 110!