Harman Kardon AVR 3600 Owners Manual - Page 47

Learning, Resetting the Remote, PROCESSOR RESET, MEMORY - factory reset

Get Harman Kardon AVR 3600 PDF manuals and user guides View all Harman Kardon AVR 3600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

ADVANCED FUNCTIONS NOTE: Use caution when programming complicated activities. It isn't possible to program a pause or delay before sending commands after Power On, and the component may not be ready to respond to commands immediately after powering on. To program, or "record" an activity, follow these steps: 1. To enter Program mode, simultaneously press and hold the Activity Button and the Alphanumeric Key or AVR Power On or Off Button to which the activity will be assigned. 2. Press the Source Selector (or Setup Button) for each device before you enter individual commands. This step counts as one of the 19 commands allowed for each activity. 3. For Power On, press the AVR or Device Power On Button. 4. Press the AVR or Device Power Off Button for Power Off. 5. Press the Activity Button to end the programming process, and the last Source Selector (or the Setup Button) will flash three times. It isn't possible to "edit" a command within an activity. To erase the activity: 1. Press and hold the Activity Button and the Alphanumeric Key or AVR Power On or Off Button until the Source Selector or Setup Button lights. 2. Press the Activity Button to erase the activity. To execute an activity, press the Activity Button, then press the Alphanumeric Key (or the AVR Power On or Off Button) for the Activity. Learning If you have programmed a product's codes into the remote and find that some functions are missing, the AVR 3600 remote may "learn" individual codes from the product's original remote. See page 26. Resetting the Remote To reset the remote to its factory defaults, simultaneously press and hold the TV Source Selector and the "0" Alphanumeric Key. When the TV Button re-lights, enter the code "333". When the TV Button goes out, and all of the Source Selectors flash, the remote will be reset. PROCESSOR RESET If the unit behaves erratically after a power surge, first tun off the Main Power Switch and unplug the AC power cord for at least 3 minutes. Plug the cord back in and turn the receiver on. If this doesn't help, reset the AVR. NOTE: A system reset erases all user configurations, including video resolution, speaker and level settings, and tuner presets. After a reset, reenter all of these settings from your notes in the appendix worksheets. To reset the AVR 3600, place it in Standby mode (press the frontpanel Standby/On Switch so that the Power Indicator turns amber). Then press and hold the front-panel OK Button for at least 5 seconds until the RESET message appears. If the receiver does not function correctly ofter a processor reset, contact an authorized Harman Kardon service center for assistance Authorized service centers may be located by visiting the Web site at www.harmankardon.com. NOTE: After performing a system reset, wait at least 1 minute before pressing any Source Selectors. MEMORY If the AVR 3600 is unplugged or experiences a power outage, it will retain user settings for up to four weeks. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
47
ADVANCED FUNCTIONS
NOTE:
Use caution when programming complicated activities.
It isn’t possible to program a pause or delay before sending
commands after Power On, and the component may not be
ready to respond to commands immediately after powering on.
To program, or “record” an activity, follow these steps:
1. To enter Program mode, simultaneously press and hold the
Activity Button and the Alphanumeric Key or AVR Power On or Off
Button to which the activity will be assigned.
2. Press the Source Selector (or Setup Button) for each device
before you enter individual commands. This step counts as one
of the 19 commands allowed for each activity.
3. For Power On, press the AVR or Device Power On Button.
4. Press the AVR or Device Power Off Button for Power Off.
5. Press the Activity Button to end the programming process, and
the last Source Selector (or the Setup Button) will flash three
times.
It isn’t possible to “edit” a command within an activity. To erase the
activity:
1. Press and hold the Activity Button and the Alphanumeric Key or
AVR Power On or Off Button until the Source Selector or Setup
Button lights.
2. Press the Activity Button to erase the activity.
To execute an activity, press the Activity Button, then press the
Alphanumeric Key (or the AVR Power On or Off Button) for the
Activity.
Learning
If you have programmed a product’s codes into the remote and find
that some functions are missing, the AVR 3600 remote may “learn”
individual codes from the product’s original remote. See page 26.
Resetting the Remote
To reset the remote to its factory defaults, simultaneously press and
hold the TV Source Selector and the “0” Alphanumeric Key. When
the TV Button re-lights, enter the code “333”. When the TV Button
goes out, and all of the Source Selectors flash, the remote will be
reset.
PROCESSOR RESET
If the unit behaves erratically after a power surge, first tun off the
Main Power Switch and unplug the AC power cord for at least
3 minutes. Plug the cord back in and turn the receiver on. If this
doesn’t help, reset the AVR.
NOTE:
A system reset erases all user configurations, includ-
ing video resolution, speaker and level settings, and tuner
presets. After a reset, reenter all of these settings from your
notes in the appendix worksheets.
To reset the AVR 3600, place it in Standby mode (press the front-
panel Standby/On Switch so that the Power Indicator turns amber).
Then press and hold the front-panel OK Button for at least 5 seconds
until the RESET message appears.
If the receiver does not function correctly ofter a processor reset,
contact an authorized Harman Kardon service center for assistance
Authorized service centers may be located by visiting the Web site
at www.harmankardon.com.
NOTE:
After performing a system reset, wait at least 1 minute
before pressing any Source Selectors.
MEMORY
If the AVR 3600 is unplugged or experiences a power outage, it will
retain user settings for up to four weeks.