Harman Kardon AVR 8000 Owners Manual - Page 37

Advanced Features

Get Harman Kardon AVR 8000 PDF manuals and user guides View all Harman Kardon AVR 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Advanced Features Note that this setting is temporary and will remain active only until it is changed or until the AVR 8000 is turned off. Once the unit is turned off, the semi-OSD displays will remain activated, even if they were switched off for the previous listening session. To change the length of time that the semi-OSD displays remain on the screen, go to the ADVANCED menu as outlined earlier, and press the ⁄/¤ Buttons mp as needed, until the on-screen › cursor is next to the SEMI OSD TIME OUT line. Next, press the ‹/› Buttons n 39 until the desired time in seconds is displayed. Note that unlike most of the other options in this menu, this is a permanent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off. If you wish to make other adjustments, press the ⁄/¤ Buttons mp until the on-screen › cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set Button o. If you have no other adjustments to make, press the OSD Button v to exit the menu system. Full-OSD Time-Out Adjustment The FULL OSD menu system is used to simplify the setup and adjustment of the AVR 8000, using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of inactivity before they disappear from the screen (Time-Out). Time-Out is a safety measure to prevent image retention of the menu text in your monitor or projector, which might happen if it were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the Time-Out display. To change the full-OSD Time-Out, you will need to make an adjustment in the ADVANCED menu (Figure 12). To start the adjustment, press the OSD Button v to bring the MASTER MENU to the screen. Press the ¤ Button p, until the on-screen ¤ cursor is next to the ADVANCED line. Press the Set Button o to enter the ADVANCED menu (Figure 12). At the ADVANCED menu (Figure 12) make certain that the on-screen › cursor is next to the FULL OSD TIME OUT line by press- ing the ⁄/¤ Buttons mp as needed. Next, press the ‹/› Buttons n 39 until the desired time is displayed in seconds. Note that unlike most of the other options in this menu, this is a permanent setting change, and the Time-Out entry will remain in effect until it is changed, even if the unit is turned off. If you wish to make other adjustments, press the ⁄/¤ Buttons mp until the on-screen › cursor is next to the desired setting or the RETURN TO MASTER MENU line and press the Set Button o. If you have no other adjustments to make, press the OSD Button v to exit the menu system. 37 ADVANCED FEATURES

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
37
ADVANCED FEATURES
Advanced Features
Note that this setting is temporary and will
remain active only until it is changed or until
the AVR 8000 is turned off. Once the unit is
turned off, the semi-OSD displays will remain
activated, even if they were switched off for the
previous listening session.
To change the length of time that the semi-OSD
displays remain on the screen, go to the
ADVANCED
menu as outlined earlier, and
press the
⁄
/
¤
Buttons
mp
as needed,
until the on-screen
›
cursor is next to the
SEMIOSDTIMEOUT
line. Next, press
the
‹
/
›
Buttons
n
until the desired
time in seconds is displayed. Note that unlike
most of the other options in this menu, this is a
permanent setting change, and the time-out
entry will remain in effect until it is changed,
even when the unit is turned off.
If you wish to make other adjustments, press
the
⁄
/
¤
Buttons
mp
until the on-screen
›
cursor is next to the desired setting or the
BACKTOMASTERMENU
line and
press the
Set Button
o
. If you have no
other adjustments to make, press the
OSD
Button
v
to exit the menu system.
Full-OSD Time-Out Adjustment
The
FULLOSD
menu system is used to
simplify the setup and adjustment of the
AVR 8000, using a series of on-screen menus.
The factory default setting for these menus
leaves them on the screen for 20 seconds after
a period of inactivity before they disappear
from the screen (Time-Out). Time-Out is a safety
measure to prevent image retention of the
menu text in your monitor or projector, which
might happen if it were left on indefinitely.
However, some viewers may prefer a slightly
longer or shorter period before the Time-Out
display.
To change the full-OSD Time-Out, you will need
to make an adjustment in the
ADVANCED
menu (Figure 12). To start the adjustment, press
the
OSD Button
v
to bring the
MASTER
MENU
to the screen. Press the
¤
Button
p
, until the on-screen
¤
cursor is next to the
ADVANCED
line. Press the
Set Button
o
to enter the
ADVANCED
menu (Figure 12).
At the
ADVANCED
menu (Figure 12) make
certain that the on-screen
›
cursor is next to
the
FULLOSDTIMEOUT
line by press-
ing the
⁄
/
¤
Buttons
mp
as needed.
Next, press the
‹
/
›
Buttons
n
until the
desired time is displayed in seconds. Note that
unlike most of the other options in this menu,
this is a permanent setting change, and the
Time-Out entry will remain in effect until it is
changed, even if the unit is turned off.
If you wish to make other adjustments, press
the
⁄
/
¤
Buttons
mp
until the on-screen
›
cursor is next to the desired setting or the
RETURNTOMASTERMENU
line and
press the
Set Button
o
. If you have no
other adjustments to make, press the
OSD
Button
v
to exit the menu system.
39
39