Hayward HeatPro® Heat Pro All Models - Page 38

OBTAINING SERVICE ASSISTANCE, Before You Call For Service

Get Hayward HeatPro® PDF manuals and user guides View all Hayward HeatPro® manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Heat Pump Pool / Spa Heater Owner's Manual OBTAINING SERVICE ASSISTANCE Before You Call For Service If there appears to be a problem, refer to the installation troubleshooting guide above. There is an additional troubleshooting chart available at the end of the owner's manual containing information for troubleshooting your heat pump. 1. Make sure that the swimming pool filtration system is turned on. 2. Is the main power (circuit breaker) on? 3. Is the "Power" indicator light illuminated? 4. Is the Heat Pump Thermostat set at a high enough level to enable the system to turn on? Adjust the thermostat to a higher setting. 5. Check the outside temperature. HAYWARD Heat Pumps will not turn on when the outside air temperatures drop near 45 degrees. 6. Make sure that the pump and skimmer baskets are free off debris. Also ensure that the pool filter is clean and supplying proper water flow to the Heat Pump. 7. The heat pump is not able to maintain your desired temperature? Depending on the time of the year, you may need to adjust your pool filtration systems hours of operation (increase run time). Note: Use a solar blanket/cover on the surface in order to keep a higher level of heat retention. Heat Pumps with Electronic Displays 1. If diagnostic code "PS" is illuminated, this indicates improper water flow. Ensure that pool filter pump basket, skimmer basket, and filter are free of debris and clean. 2. If diagnostic code "LP" is illuminated, this indicates that the outside air temperature is too low. When this occurs the Heat Pump shuts itself off automatically. When the outside air temperature rises enough the heat pump will automatically turn on. 3. If diagnostic code "HP" is illuminated, this indicates that a low water flow condition may exist. Check to see that the pool pump basket, skimmer basket and pool filter is clean. After checking these items, if the "HP" indicator is still illuminated contact HAYWARD for service. Service Information Hayward Pool Products 1-800-432-8387 Hayward Pool Products 1 Hayward Industrial Drive Clemmons, NC 27012 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Heat Pump Pool / Spa Heater Owner’s Manual
37
OBTAINING SERVICE ASSISTANCE
Before You Call For Service
If there appears to be a problem, refer to the installation troubleshooting guide above. There is an
additional troubleshooting chart available at the end of the owner’s manual containing
information for troubleshooting your heat pump.
1. Make sure that the swimming pool filtration system is turned on.
2.
Is the main power (circuit breaker) on?
3. Is the "Power" indicator light illuminated?
4. Is the Heat Pump Thermostat set at a high enough level to enable the system to turn on? Adjust the
thermostat to a higher setting.
5. Check the outside temperature. HAYWARD Heat Pumps will not turn on when the outside air temperatures drop
near 45 degrees.
6. Make sure that the pump and skimmer baskets are free off debris. Also ensure that the pool filter is
clean and supplying proper water flow to the Heat Pump.
7. The heat pump is not able to maintain your desired temperature? Depending on the time of the year, you may need
to adjust your pool filtration systems hours of operation (increase run time).
Note
: Use a solar blanket/cover on the surface in order to keep a higher level of heat retention.
Heat Pumps with Electronic Displays
1. If diagnostic code "PS" is illuminated, this indicates improper water flow. Ensure that pool filter pump basket,
skimmer basket, and filter are free of debris and clean.
2. If diagnostic code “LP” is illuminated, this indicates that the outside air temperature is too low. When this occurs
the Heat Pump shuts itself off automatically. When the outside air temperature rises enough the heat pump will
automatically turn on.
3. If diagnostic code "HP" is illuminated, this indicates that a low water flow condition may exist. Check to see that
the pool pump basket, skimmer basket and pool filter is clean. After checking these items, if the "HP" indicator is
still illuminated contact HAYWARD for service.
Service Information
Hayward Pool Products
1-800-432-8387
Hayward Pool Products
1 Hayward Industrial Drive
Clemmons, NC 27012