Hayward OnCommand Model: ALL MODELS Installation - Page 13

Pentair/Purex/MiniMax, Raypak RP2100 Pool/Spa Heater - remote

Get Hayward OnCommand PDF manuals and user guides View all Hayward OnCommand manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Pentair/Purex/MiniMax 1. Turn power off to heater. 2. Remove factory installed jumper from the "Ext Switch" connector. 3. Wire the OnCommand to the "Ext Switch" connector as shown below. 4. The wires to the OnCommand must be separated from any line voltage wires. Failure to follow these instructions may cause erratic operation of the heater. 5. Set the Power (Thermostat Select) switch to either "Pool" or "Spa". 6. Set the "Pool" and "Spa" thermostats to their maximum settings. Remove Factory Jumper Ext. Switch MINIMAX Raypak RP2100 Pool/Spa Heater 1. Turn power off to heater. 2. Push the mode button to "spa" mode. 3. Set the temperature to the maximum. 4. Push the mode button to "OFF". 5. Lastly, plug the prewired connector in the P7 position on the board. ! IMPORTANT: The heater will display "OFF" when it is being remotely controlled by the OnCommand. Some homeowners see the "OFF" display and, thinking this is a mistake, change the mode to "POOL" or "SPA" which then disables the remote control by the OnCommand. To prevent this: Remove the heater touch pad connector (P5) which will disable the touchpad. Black Orange Stripe Orange Black Stripe Light Blue P7 RAYPAK RP2100 Drawing is for digital heater. If heater is a millivolt (analog) run red wires from Fireman's Switch to heater relay. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Pentair/Purex/MiniMax
1.
Turn power off to heater.
2.
Remove factory installed jumper from the “Ext Switch” connector.
3.
Wire the OnCommand to the “Ext Switch” connector as shown below.
4.
The wires to the OnCommand must be separated from any line voltage wires.
Failure to follow these
instructions may cause erratic operation of the heater.
5.
Set the Power (Thermostat Select) switch to either “Pool” or “Spa”.
6.
Set the “Pool” and “Spa” thermostats to their maximum settings.
Raypak RP2100 Pool/Spa Heater
1.
Turn power off to heater.
2.
Push the mode button to “spa” mode.
3.
Set the temperature to the maximum.
4.
Push the mode button to “OFF”.
5.
Lastly, plug the
prewired connector in the P7 position on the board.
!
IMPORTANT:
The heater will display “OFF” when it is being remotely controlled by the
OnCommand.
Some homeowners see the “OFF” display and, thinking this is a mistake, change the
mode to “POOL” or “SPA” which then disables the remote control by the OnCommand.
To prevent
this:
Remove the heater touch pad connector (P5) which will disable the touchpad.
10
MINIMAX
Ext.
Switch
Remove
Factory Jumper
P7
Light Blue
Black
Orange Stripe
Orange
Stripe
Black
RAYPAK RP2100
Drawing is for digital heater. If heater is a
millivolt (analog) run red wires from Fireman’s
Switch to heater relay.