HP 220mx HP SureStore 220mx Optical Jukebox User's Guide - Page 61

Changing the Jukebox Controller ID

Get HP 220mx PDF manuals and user guides View all HP 220mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Operating the Jukebox NOTE NOTE Operating the Jukebox Changing SCSI IDs assigned one ID and one ID is assigned to each disk drive. The default SCSI IDs are as follows • jukebox controller = 3 disk drive 1 (lower drive) = 4 disk drive 2 (upper drive in a two-drive model) = 5 If you are already using one of these IDs for your host bus adapter or another SCSI peripheral device, follow the directions in one of the next two sections to change either the jukebox controller or a drive ID. Changing the Jukebox Controller ID Start with READY or SECURE in the display. 1. Press NEXT until SCSI ID * displays. 2. Press ENTER. AC ID * displays. ("AC" is the "jukebox controller.") 3. Press ENTER. AC ID 3 displays. 4. Press NEXT or PREV until the ID you want displays. 5. Press ENTER. SET # (# is a number from 0-7) displays briefly and then AC ID * displays again. The ID you chose is now set. 6. Press CANCEL two times to return to the READY state. CONFLICT displays if you attempt to set the jukebox controller and a drive to the same ID. Repeat the procedure and reset one of the IDs to another, non-conflicting ID. After you change an ID you may have to restart your host computer for the new ID to be recognized. Chapter 3 3-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Chapter 3
3-23
Operating the Jukebox
Changing SCSI IDs
Operating the Jukebox
assigned one ID and one ID is assigned to each disk drive.
The default SCSI IDs are as follows
•
jukebox controller = 3
disk drive 1 (lower drive) = 4
disk drive 2 (upper drive in a two-drive model) = 5
If you are already using one of these IDs for your host bus adapter or
another SCSI peripheral device, follow the directions in one of the next
two sections to change either the jukebox controller or a drive ID.
Changing the Jukebox Controller ID
Start with
READY
or
SECURE
in the display.
1. Press
NEXT
until
SCSI ID *
displays.
2. Press
ENTER
.
AC ID *
displays. (
“
AC
”
is the
“
jukebox controller.
”
)
3. Press
ENTER
.
AC ID 3
displays.
4. Press
NEXT
or
PREV
until the ID you want displays.
5. Press
ENTER
.
SET #
(
#
is a number from 0-7) displays briefly and then
A
C ID *
displays again. The ID you chose is now set.
6. Press
CANCEL
two times to return to the
READY
state.
NOTE
CONFLICT
displays if you attempt to set the jukebox controller and a
drive to the same ID. Repeat the procedure and reset one of the IDs to
another, non-conflicting ID.
NOTE
After you change an ID you may have to restart your host computer for
the new ID to be recognized.