HP 220mx HP SureStore 220mx Optical Jukebox User's Guide - Page 62

Changing an Optical Drive ID

Get HP 220mx PDF manuals and user guides View all HP 220mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

CAUTION NOTE NOTE Operating the Jukebox Changing SCSI IDs Do not turn power to STANDBY in this jukebox until you are sure the SCSI bus is inactive. Removing power from a SCSI peripheral when the bus is active can result in data loss and/or indeterminate bus states. Check your host system manuals for information about checking the SCSI bus status. Changing an Optical Drive ID Start with READY or SECURE in the display. 1. Press NEXT until SCSI ID * displays. 2. Press ENTER. AC ID * displays. ("AC" is the "jukebox controller.") 3. Press NEXT until DRV 1 ID * or DRV 2 ID * (if your jukebox has two drives) displays. 4. Press ENTER. DRV # ID? displays, where "#" is the number of the drive you selected in step 3 and "?" is the ID to which your selected drive is currently set. 5. Press NEXT until the ID you want displays. 6. Press ENTER. SET # (# is a number from 0-7) displays briefly and then DRV # ID # displays again. The ID you chose is now set. 7. Press CANCEL two times to return to the READY state. CONFLICT displays if you attempt to set the jukebox controller and a drive to the same ID. Repeat the procedure and reset one of the IDs to another, non-conflicting ID. After you change an ID you may have to restart your host computer for the new ID to be recognized. 3- 24 Chapter 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
3-24
Chapter 3
Operating the Jukebox
Changing SCSI IDs
CAUTION
Do not turn power to STANDBY in this jukebox until you are sure the
SCSI bus is inactive. Removing power from a SCSI peripheral when the
bus is active can result in data loss and/or indeterminate bus states.
Check your host system manuals for information about checking the
SCSI bus status.
Changing an Optical Drive ID
Start with
READY
or
SECURE
in the display.
1. Press
NEXT
until
SCSI ID *
displays.
2. Press
ENTER
.
AC ID *
displays. (
“
AC
”
is the
“
jukebox controller.
”
)
3. Press
NEXT
until
DRV 1 ID *
or
DRV 2 ID *
(if your jukebox has two
drives) displays.
4. Press
ENTER
.
DRV # ID?
displays, where
“
#
”
is the number of the drive
you selected in step 3 and
“
?
”
is the ID to which your selected drive is
currently set.
5. Press
NEXT
until the ID you want displays.
6. Press
ENTER
.
SET #
(
#
is a number from 0-7) displays briefly and then
DRV # ID #
displays again. The ID you chose is now set.
7. Press
CANCEL
two times to return to the
READY
state.
NOTE
CONFLICT
displays if you attempt to set the jukebox controller and a
drive to the same ID. Repeat the procedure and reset one of the IDs to
another, non-conflicting ID.
NOTE
After you change an ID you may have to restart your host computer for
the new ID to be recognized.