HP 220mx HP SureStore 1200mx/2200mx Optical Jukebox User's Guide - Page 17

Identifying Right-Side Panel Features

Get HP 220mx PDF manuals and user guides View all HP 220mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Chapter 1: Setting upStheettiDngiskUpDrthivee Jukebox Setting Up the Jukebox Identifying Right-Side Panel Features The numbers below correspond to the numbers in Figure 1-1 on the previous page 1 Active bus indicator 2 SCSI interface selection switch 3 SCSI ports 4 Power cord strain relief clip 5 Product serial number label 6 Access panel and mounting screws 7 Cable access hole 8 Power switch 9 Power receptacle Lit when the SCSI bus is active. There is an indicator for each single-ended and each differential interface in the jukebox. Used to select either a single-ended or differential SCSI interface on the SCSI interface board. In 4- or 6-drive jukeboxes, there is one interface board. In 10-drive jukeboxes, there are two interface boards, designated Bus 1 and Bus 2. The interface selection switch must be set individually for each board Used for connecting SCSI cables to the interface board. The interface board has two types of interface; single-ended and differential. Each type of interface has two ports Used to route the power cord away from other connectors and provide strain relief for the power cord connection. Needed for service calls. Write down your jukebox serial number before you call your service representative. Panel that covers the interface and power connection components. The panel is secured by two screws on the lower corners. (See the following note.) Continued on the next page Used to pass SCSI and power cables through to the inside of the jukebox. The power switch is under the panel but can be operated through the hole in the panel. Turns power ON and OFF to the jukebox. Receptacle for the jukebox power cord. Located on the bottom of the power distribution assembly. Chapter 1 1- 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Chapter 1
1-5
Setting Up the Jukebox
Identifying Right-Side Panel Features
Chapter 1: Setting
up the Disk Drive
Setting Up the
Jukebox
The numbers below correspond to the numbers in Figure 1-1 on the previous
page
1
Active bus
indicator
Lit when the SCSI bus is active.
There is an indicator
for each single-ended and each differential interface in
the jukebox.
2
SCSI interface
selection switch
Used to select either a single-ended or differential SCSI
interface on the SCSI interface board.
In 4- or 6-drive jukeboxes, there is one interface board.
In 10-drive jukeboxes, there are two interface boards,
designated Bus 1 and Bus 2. The interface selection
switch must be set individually for each board
3
SCSI ports
Used for connecting SCSI cables to the interface board.
The interface board has two
types
of interface;
single-ended and differential. Each
type
of interface has
two ports
4
Power cord strain
relief clip
Used to route the power cord away from other
connectors and provide strain relief for the power cord
connection.
5
Product serial
number label
Needed for service calls. Write down your jukebox
serial number before you call your service
representative.
6
Access panel and
mounting screws
Panel that covers the interface and power connection
components. The panel is secured by two screws on the
lower corners.
(See the following note.)
Continued on the next page
7
Cable access hole
Used to pass SCSI and power cables through to the
inside of the jukebox.
8
Power switch
The power switch is under the panel but can be operated
through the hole in the panel. Turns power ON and OFF
to the jukebox.
9
Power receptacle
Receptacle for the jukebox power cord. Located on the
bottom of the power distribution assembly.