HP 220mx HP SureStore 1200mx/2200mx Optical Jukebox User's Guide - Page 29

Connecting Power

Get HP 220mx PDF manuals and user guides View all HP 220mx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 1: Setting upStheettiDngiskUpDrthivee Jukebox NOTE NOTE NOTE Setting Up the Jukebox Connecting Power Connecting Power 1. Ensure that the power switch on the jukebox is OFF ("5" on Figure 1-1) Use the power cord shipped with the jukebox. 2. Route the power cord through the strain relief clip ("4" on Figure 1-1) and close the clip snugly around the cord. 3. Plug the socket end of the power cord into the power port on bottom of the power distribution assembly ( "9" on Figure 1-1). 4. Continue to route the power cable down, through the long cable slot at the bottom of the jukebox right side panel, and out through the cable access hole at the lower left rear of the jukebox ("7" on Figure 1-1). 5. Plug the other end of the power cord into a three-hole grounded outlet. 6. Press the power switch ON ("8" on Figure 1-1) When power is applied, TESTING and NOT READY alternately display. Once the poweron test completes (approximately 1.5 minutes), READY displays. If DEVICE FAILED displays. See "Troubleshooting" in Chapter 3 for troubleshooting procedures. 7. Refer to Chapter 3, "Operating the Jukebox" for instructions on setting the SCSI addresses, loading optical disks into the jukebox, setting a password, etc. Continue on to "Configuring Write Verify" on the next page. Chapter 1 1-17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Chapter 1
1-17
Setting Up the Jukebox
Connecting Power
Chapter 1: Setting
up the Disk Drive
Setting Up the
Jukebox
Connecting Power
1.
Ensure that the power switch on the jukebox is OFF (
“
5
”
on Figure 1-1)
NOTE
Use the power cord shipped with the jukebox.
2.
Route the power cord through the strain relief clip (
“
4
”
on Figure 1-1) and close
the clip snugly around the cord.
3.
Plug the socket end of the power cord into the power port on bottom of the
power distribution assembly (
“
9
”
on Figure 1-1).
4.
Continue to route the power cable down, through the long cable slot at the
bottom of the jukebox right side panel, and out through the cable access hole at
the lower left rear of the jukebox (
“
7
”
on Figure 1-1).
5.
Plug the other end of the power cord into a three-hole grounded outlet.
6.
Press the power switch ON (
“
8
”
on Figure 1-1)
When power is applied, TESTING and NOT READY alternately display. Once
the poweron test completes (approximately 1.5 minutes), READY displays.
NOTE
If
DEVICE FAILED
displays. See
“
Troubleshooting
”
in Chapter 3 for
troubleshooting procedures.
7.
Refer to Chapter 3,
“
Operating the Jukebox
”
for instructions on setting the SCSI
addresses, loading optical disks into the jukebox, setting a password, etc.
NOTE
Continue on to
“
Configuring Write Verify
”
on the next page.