HP 3PAR StoreServ 7200 2-node HP 3PAR SmartStart 1.1.1 User's Guide ( - Page 8

For more information, see your completed Storage System Software Installation Checklist

Get HP 3PAR StoreServ 7200 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7200 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

◦ The HP 3PAR storage system setup is verified, the storage system is powered on, and the LEDs are functioning correctly. ◦ Either the physical Service Processor is installed and powered on, and you have assigned an IP address; or the virtual Service Processor (VSP) is installed and connected, and you have determined the temporary IP address. • Make sure you have: ◦ Administrative access to the Windows host systems you are configuring If you are planning to configure a remote host system (a machine other than the machine into which you inserted the SmartStart media), you must be able to use the same ID and password to gain administrator access to both the system running SmartStart (the local host) and the remote host. ◦ Rights to configure storage To configure storage, your user account on the HP 3PAR storage system must be assigned either a Super or Edit role, or be granted these rights: host_create, vv_create, and vlun_create. ◦ HP 3PAR storage system and Service Processor information necessary for initialization and configuration For more information, see your completed Storage System Software Installation Checklist from the HP 3PAR StoreServ 7000 Site Planning Manual. Service Processor information: - The Service Processor IP address, subnet mask, and gateway IP address For more information on determining the temporary IP address and assigning the permanent IP address, see the HP 3PAR StoreServ 7000 Storage Installation Guide. - Hostname to assign - DNS settings (if applicable) - Proxy server settings (if applicable) - New password to assign to the username for the two system setup wizards (setupusr) - New password to assign to the username for the Service Processor (3parcust) NOTE: Passwords for setupusr and 3parcust usernames must be between 7 and 32 characters in length and can consist of alphanumeric characters and the following special characters: period (.), plus (+), dash(-), equal (=), and forward slash (/). HP 3PAR StoreServ Storage system information: - Storage system serial number This 7-digit number is located on the back of your HP 3PAR StoreServ Storage system next to the power switch for the node enclosure power cooling module (PCM1), and begins with 16 (e.g., 1624635). "Locating the Serial Number" (page 14) - Storage system name - IP address (IPv4 only) - Subnet mask - Gateway IP address - New password to assign to the username for the storage system (3paradm) 8 Prepare to Configure

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
◦
The HP 3PAR storage system setup is verified, the storage system is powered on, and the
LEDs are functioning correctly.
◦
Either the physical
Service Processor
is installed and powered on, and you have assigned
an IP address; or the virtual Service Processor (
VSP
) is installed and connected, and you
have determined the temporary IP address.
•
Make sure you have:
Administrative access to the Windows host systems you are configuring
If you are planning to configure a remote host system (a machine other than the machine
into which you inserted the SmartStart media), you must be able to use the same ID and
◦
password to gain administrator access to both the system running SmartStart (the local
host) and the remote host.
◦
Rights to configure storage
To configure storage, your user account on the HP 3PAR storage system must be assigned
either a Super or Edit role, or be granted these rights: host_create, vv_create, and
vlun_create.
◦
HP 3PAR storage system and Service Processor information necessary for initialization
and configuration
For more information, see your completed Storage System Software Installation Checklist
from the
HP 3PAR StoreServ 7000 Site Planning Manual
.
Service Processor information:
–
The Service Processor IP address, subnet mask, and gateway IP address
For more information on determining the temporary IP address and assigning the
permanent IP address, see the
HP 3PAR StoreServ 7000 Storage Installation Guide
.
–
Hostname to assign
–
DNS settings (if applicable)
–
Proxy server settings (if applicable)
–
New password to assign to the username for the two system setup wizards (
setupusr
)
–
New password to assign to the username for the Service Processor (
3parcust
)
NOTE:
Passwords for setupusr and 3parcust usernames must be between 7 and 32
characters in length and can consist of alphanumeric characters and the following special
characters: period (.), plus (+), dash(-), equal (=), and forward slash (/).
HP 3PAR StoreServ Storage system information:
–
Storage system serial number
This 7-digit number is located on the back of your HP 3PAR StoreServ Storage system
next to the power switch for the node enclosure power cooling module (PCM1), and
begins with
16
(e.g., 1624635).
“Locating the Serial Number” (page 14)
–
Storage system name
–
IP address (IPv4 only)
–
Subnet mask
–
Gateway IP address
–
New password to assign to the username for the storage system (
3paradm
)
8
Prepare to Configure