HP 3PAR StoreServ 7200 2-node HP 3PAR StoreServ 7000 Storage Service Guide - Page 28

Replace the SFP. See, showport -sfp, showport, ready

Get HP 3PAR StoreServ 7200 2-node PDF manuals and user guides View all HP 3PAR StoreServ 7200 2-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

- - - 0:3:1 peer offline - 0002AC8004DB rcip - - 1:0:1 initiator ready 50002ACFF70185A6 50002AC1010185A6 disk - - - 1:0:2 initiator ready 50002ACFF70185A6 50002AC1020185A6 disk - - - 1:1:1 target ready 2FF70002AC0185A6 21110002AC0185A6 host - - - 1:1:2 target loss_sync 2FF70002AC0185A6 21120002AC0185A6 free - - - 1:2:1 initiator loss_sync 2FF70002AC0185A6 21210002AC0185A6 free - - - 1:2:2 initiator loss_sync 2FF70002AC0185A6 21220002AC0185A6 free - - - 1:2:3 initiator loss_sync 2FF70002AC0185A6 21230002AC0185A6 free - - - 1:2:4 initiator loss_sync 2FF70002AC0185A6 21240002AC0185A6 free - - - 1:3:1 peer offline - 0002AC8004BD rcip - - IP RCIP0 SAS SAS FC FC FC FC FC FC IP RCIP1 • showport -sfp to verify which SFP requires replacement: cli%showport -sfp N:S:P -State- -Manufacturer- MaxSpeed(Gbps) TXDisable TXFault RXLoss DDM 0:1:1 OK HP-F 8.5 No No No Yes 0:1:2 OK HP-F 8.5 No No No Yes 0:2:1 OK AVAGO 10.3 No No Yes Yes 0:2:2 OK AVAGO 10.3 No No Yes Yes 1:1:1 OK HP-F 8.5 No No No Yes 1:1:2 - - - - - - - 1:2:1 OK HP-F 8.5 No No Yes Yes 1:2:2 OK HP-F 8.5 No No Yes Yes 1:2:3 OK HP-F 8.5 No No Yes Yes 1:2:4 OK HP-F 8.5 No No Yes Yes 3. Replace the SFP. See "Replacing an SFP" (page 30). 4. Issue the following commands: • showport to verify that the ports are in good condition and the State is listed as ready: cli%showport N:S:P Mode State Node_WWN Port_WWN/HW_Addr Type Protocol Label Partner FailoverState 0:0:1 initiator ready 50002ACFF70185A6 50002AC0010185A6 disk SAS - - - 0:0:2 initiator ready 50002ACFF70185A6 50002AC0020185A6 disk SAS - - - 0:1:1 target ready 2FF70002AC0185A6 20110002AC0185A6 host FC - - - 0:1:2 target ready 2FF70002AC0185A6 20120002AC0185A6 host FC - - - 0:2:1 target loss_sync - 2C27D75301F6 iscsi iSCSI - - - 0:2:2 target loss_sync - 2C27D75301F2 iscsi iSCSI - - - 0:3:1 peer offline - 0002AC8004DB rcip IP RCIP0 - - 1:0:1 initiator ready 50002ACFF70185A6 50002AC1010185A6 disk SAS - - - 1:0:2 initiator ready 50002ACFF70185A6 50002AC1020185A6 disk SAS - 28 Servicing the Storage System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
-
-
-
0:3:1
peer
offline
- 0002AC8004DB
rcip
IP RCIP0
-
-
1:0:1 initiator
ready 50002ACFF70185A6 50002AC1010185A6 disk
SAS
-
-
-
1:0:2 initiator
ready 50002ACFF70185A6 50002AC1020185A6 disk
SAS
-
-
-
1:1:1
target
ready 2FF70002AC0185A6 21110002AC0185A6 host
FC
-
-
-
1:1:2
target loss_sync 2FF70002AC0185A6 21120002AC0185A6 free
FC
-
-
-
1:2:1 initiator loss_sync 2FF70002AC0185A6 21210002AC0185A6 free
FC
-
-
-
1:2:2 initiator loss_sync 2FF70002AC0185A6 21220002AC0185A6 free
FC
-
-
-
1:2:3 initiator loss_sync 2FF70002AC0185A6 21230002AC0185A6 free
FC
-
-
-
1:2:4 initiator loss_sync 2FF70002AC0185A6 21240002AC0185A6 free
FC
-
-
-
1:3:1
peer
offline
- 0002AC8004BD
rcip
IP RCIP1
-
-
•
showport -sfp
to verify which SFP requires replacement:
cli%showport -sfp
N:S:P -State- -Manufacturer- MaxSpeed(Gbps) TXDisable TXFault RXLoss DDM
0:1:1 OK
HP-F
8.5
No
No
No
Yes
0:1:2 OK
HP-F
8.5
No
No
No
Yes
0:2:1 OK
AVAGO
10.3
No
No
Yes
Yes
0:2:2 OK
AVAGO
10.3
No
No
Yes
Yes
1:1:1 OK
HP-F
8.5
No
No
No
Yes
1:1:2 -
-
-
-
-
-
-
1:2:1 OK
HP-F
8.5
No
No
Yes
Yes
1:2:2 OK
HP-F
8.5
No
No
Yes
Yes
1:2:3 OK
HP-F
8.5
No
No
Yes
Yes
1:2:4 OK
HP-F
8.5
No
No
Yes
Yes
3.
Replace the SFP. See
“Replacing an SFP” (page 30)
.
4.
Issue the following commands:
•
showport
to verify that the ports are in good condition and the
State
is listed as
ready
:
cli%showport
N:S:P
Mode
State Node_WWN
Port_WWN/HW_Addr Type Protocol Label
Partner FailoverState
0:0:1 initiator ready 50002ACFF70185A6 50002AC0010185A6 disk
SAS
-
-
-
0:0:2 initiator ready 50002ACFF70185A6 50002AC0020185A6 disk
SAS
-
-
-
0:1:1 target
ready 2FF70002AC0185A6 20110002AC0185A6 host
FC
-
-
-
0:1:2 target
ready 2FF70002AC0185A6 20120002AC0185A6 host
FC
-
-
-
0:2:1 target
loss_sync
-
2C27D75301F6
iscsi iSCSI
-
-
-
0:2:2 target
loss_sync
-
2C27D75301F2
iscsi iSCSI
-
-
-
0:3:1 peer
offline
-
0002AC8004DB
rcip
IP
RCIP0
-
-
1:0:1 initiator ready 50002ACFF70185A6 50002AC1010185A6 disk
SAS
-
-
-
1:0:2 initiator ready 50002ACFF70185A6 50002AC1020185A6 disk
SAS
-
28
Servicing the Storage System