HP 6400/8400 HP StorageWorks 6400/8400 Enterprise Virtual Array expansion rack - Page 38

Connect P1 I/O-A on disk enclosure 1 S-1 to P2 I/O-A on disk enclosure 25 S-25.

Get HP 6400/8400 PDF manuals and user guides View all HP 6400/8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Figure 27 EVA8400 0C9D loop 1 connections . To make the loop 1 connections between the main rack and the expansion rack: 1. Unplug DP1-A on controller A from P1 (I/O-A) on disk enclosure 1 (S-1) and: a. Connect DP1-A on controller A to P1 (I/O-A) on disk enclosure 27 (S-27). b. Connect P1 (I/O-A) on disk enclosure 1 (S-1) to P2 (I/O-A) on disk enclosure 25 (S-25). 2. Complete the following verification steps: a. Verify that the I/O modules on the added disk enclosure has been assigned an index number of the next higher enclosure number. b. In HP Command View EVA, verify that the newly added disk enclosure is listed under the array hardware in the Navigation pane and the I/O module displays a good operational status. 3. Unplug DP1-B on controller B from P1 (I/O-B) on disk enclosure 1 (S-1) and: a. Connect DP1-B on controller B to P1 (I/O-B) on disk enclosure 27 (S-27). b. Connect P1 (I/O-B) on disk enclosure 1 (S-1) to P2 (I/O-B) on disk enclosure 25 (S-25). c. Repeat Step 2. Figure 28 shows the loop 2 connections between the main rack and the expansion rack. 38 Connecting the main rack to the expansion rack

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Figure 27 EVA8400 0C9D loop 1 connections
.
To make the loop 1 connections between the main rack and the expansion rack:
1.
Unplug DP1-A on controller A from P1 (I/O-A) on disk enclosure 1 (S-1) and:
a.
Connect DP1-A on controller A to P1 (I/O-A) on disk enclosure 27 (S-27).
b.
Connect P1 (I/O-A) on disk enclosure 1 (S-1) to P2 (I/O-A) on disk enclosure 25 (S-25).
2.
Complete the following verification steps:
a.
Verify that the I/O modules on the added disk enclosure has been assigned an index number
of the next higher enclosure number.
b.
In HP Command View EVA, verify that the newly added disk enclosure is listed under the
array hardware in the Navigation pane and the I/O module displays a good operational
status.
3.
Unplug DP1-B on controller B from P1 (I/O-B) on disk enclosure 1 (S-1) and:
a.
Connect DP1-B on controller B to P1 (I/O-B) on disk enclosure 27 (S-27).
b.
Connect P1 (I/O-B) on disk enclosure 1 (S-1) to P2 (I/O-B) on disk enclosure 25 (S-25).
c.
Repeat
Step 2
.
Figure 28
shows the loop 2 connections between the main rack and the expansion rack.
Connecting the main rack to the expansion rack
38