Home » HP Manuals » Hard Drive Cases » HP AE326A » Manual Viewer

HP AE326A HP StorageWorks 1500 Modular Smart Array installation guide (355901 - Page 52

Step 10: Power on the devices, Uninterruptible Power Supplies UPS

UPC - 882780184954

Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Step 10: Power on the devices After the MSA and its storage enclosures are installed and connected to the SAN, complete the following steps to power on all of the devices in the SAN, and verify that they are operating properly. 1. Apply power to the following devices, and verify that they are in a ready state: • Uninterruptible Power Supplies (UPS) • External Fibre Channel switches 2. Power on all attached storage enclosures. NOTE: Proceed to the next step only after confirming that the external storage enclosures have completed their startup routines; otherwise, the MSA array may not properly discover the storage. 3. Press and release the Power on/Standby button on the front of the chassis to start the MSA array. The LED on the Power on/Standby button changes from amber to solid green, indicating that the MSA has been powered on. 4. Wait (up to four minutes) for the MSA to complete its startup routine. NOTE: In dual-controller configurations, each time the MSA is restarted, firmware on the two controllers is compared. If the versions are mismatched, the system prompts to clone the firmware on the controller with the latest version (higher number) over to the controller with the earlier version (lower number) firmware. The following message is displayed on the LCD panel of the controller with the earlier firmware: 07 CLONE FIRMWARE? ''= YES Press the > button on the LCD panel to clone the firmware. In dual-controller configurations, the firmware on the controllers must be the same version. 5. Press the ^ and v LCD panel message buttons on the front of each MSA controller to review the startup messages and look for the following message: Startup Complete NOTE: Proceed to the next step only after the Startup Complete message is displayed. If you power on (or restart) the server before the MSA array completes its start-up sequence, the server may not properly discover the storage. 6. Power on the servers in the SAN with access to the MSA, start the operating system, and log on as a user with administrative control. 52 Installation procedures-All deployments

Section	Page
Contents	3
Intended audience	7
Prerequisites	8
Related documentation	8
Document conventions and symbols	9
Table 1 Document conventions	9
Equipment symbols	10
Rack stability	11
HP technical support	11
HP-authorized reseller	12
Helpful websites	12
Installation procedures-All deployments	13
Figure 1: Overview of MSA installation procedures	14
Step 1: Review and confirm your plans	15
Determine which version of MSA controller firmware to use	15
Table 2 Basic MSA firmware and configuration options	16
Complete the planning worksheet on the poster	17
Go to the Internet for the most recent MSA and SAN information	18
Table 3 MSA1500 and SAN-related websites (continued)	18
Review MSA installation best practices	21
Planning	21
Installation	21
Ongoing	24
Plan your storage configuration	25
System and performance expectations	25
Striping methods	25
RAID levels	26
Table 4 RAID level comparison	26
Hard drive sizes and types	27
Spare drives	27
Array sizing (capacity)	27
Step 2: Prepare your site	28
Provide adequate structural support for the floor	28
Provide adequate clearance space and ventilation	28
Provide adequate and redundant sources of power	28
Table 5 MSA1500 specifications	29
Step 3: Install MSA option kits	30
Step 4: Rack the MSA and the storage enclosures	31
Rack installation best practices	31
Step 5: Install the hard drives	36
Step 6: Prepare your servers	37
Step 7: Install the HBA in your servers	38
Step 8: Prepare your switches	39
Step 9: Connect the cables	40
Cabling best practices	40
Connecting the SCSI cables	42
Recommended SCSI cable connections	42
Figure 2 SCSI I/O modules, bus numbers, and box numbers	42
Supported and unsupported SCSI connections	43
Table 6 Supported and Unsupported SCSI cable connections	43
Connecting the MSA to SATA storage enclosures	44
Figure 3 SCSI cable connections to two MSA20 SATA storage enclosures	44
Connecting the MSA to SCSI storage enclosures	45
Figure 4 SCSI cable connections to one MSA30 SCSI storage enclosure	45
Connecting the Fibre Channel cables	46
Connecting Fibre Channel cables in a singlepath configuration	47
Figure 5 Sample Fibre Channel cable connections, singlepath configuration	47
Connecting Fibre Channel cables in a multipath configuration	48
Figure 6 Sample Fibre Channel cable connections, multipath configuration	48
Connecting the power cords	49
Table 7 Levels of protection against power failures	49
Figure 7 Connecting the power cords using two UPSs	51
Step 10: Power on the devices	52
Verify the operating status of the MSA	53
View the LEDs on the MSA	53
Table 8 MSA1500 startup status lights	53
Read the messages on the controller display panel	54
Table 9 MSA1500 startup messages	54
Verify the operating status of the storage enclosures	54
Verify the operating status of the Fibre Channel switches	55
Verify the operating status of the servers	55
Step 11: Configure your MSA	56
Obtain desired controller firmware and Support Software CD versions	56
Determine which storage configuration utility to use	57
About the MSA Command Line Interface	57
About the Array Configuration Utility	57
About the Array Configuration Utility Command Line Interface	58
Configure the MSA	59
Configuration procedures-Windows environments	61
Prerequisites	61
Installing MSA-specific components on the servers	62
Updating MSA controller firmware (if necessary)	64
Configuring the storage	65
Configuration procedures-Linux environments	67
Prerequisites	67
Installing MSA-specific components on the servers	68
Updating MSA controller firmware (if necessary)	70
Configuring the storage	71
Configuration procedures-HP-UX environments	73
Prerequisites	73
Additional HP-UX support notes	74
Table 10 HP-UX required updates for active/active	74
Installing the ACU-CLI on the servers (optional)	75
Updating MSA controller firmware (if necessary)	76
Configuring the storage	76
Configuration procedures-OpenVMS environments	79
Prerequisites	79
Obtaining World Wide Port Names	80
Installing the current Fibre_SCSI patch on the servers	81
Table 11 OpenVMS Fibre_SCSI patches (as of August 2006)	81
Updating MSA controller firmware (if necessary)	82
Configuring the storage	82
Assigning ID Numbers to the controllers and LUNs	83
Configuration procedures-VMware environments	85
Prerequisites	85
Updating MSA controller firmware (if necessary)	86
VMware-specific tasks	86
Configuring the storage	89
Configuration procedures-Other environments	91
Prerequisites	91
Operating system-specific notes	92
NetWare environments	92
Tru64 UNIX environments	93
SCO UNIX environments	93
Updating MSA controller firmware (if necessary)	94
Configuring the storage	94
Powering off and powering on the MSA	97
Powering off the MSA	97
Powering on the MSA	98
Regulatory notices	101
Regulatory Compliance identification numbers	101
Federal Communications Commission notice	101
Modifications	101
Cables	101
Canadian notice (Avis Canadien)	101
European Union notice	102
Japanese notice	102
Japanese power cord notice	102
BSMI notice	102
Laser compliance	103
Battery replacement notice	104
Disposal of waste equipment by users in private households in the European Union	104
Electrostatic discharge	105
Prevention methods	105
Grounding methods	105
Worksheets	107
Table 12 MSA1500 information	108
Table 13 External Fibre Channel interconnect device (switch) information	109
Table 14 Server information	110
Table 15 Hard drive information	114
Table 16 Array (LUN) information	118
Index	121
A	121
B	121
C	121
D	121
E	121
F	121
G	122
H	122
I	122
L	122
M	122
N	123
O	123
P	123
R	123
S	123
T	124
U	124
V	124

Match case Limit results 1 per page

Installation procedures—All deployments

Step 10: Power on the devices

After the MSA and its storage enclosures are installed and connected to the SAN, complete the

following steps to power on all of the devices in the SAN, and verify that they are operating

properly.

Apply power to the following devices, and verify that they are in a ready state:

•

Uninterruptible Power Supplies (UPS)

•

External Fibre Channel switches

Power on all attached storage enclosures.

NOTE:

Proceed to the next step only after confirming that the external storage enclosures have

completed their startup routines; otherwise, the MSA array may not properly discover the storage.

Press and release the Power on/Standby button on the front of the chassis to start the MSA array.

The LED on the Power on/Standby button changes from amber to solid green, indicating that the

MSA has been powered on.

Wait (up to four minutes) for the MSA to complete its startup routine.

NOTE:

In dual-controller configurations, each time the MSA is restarted, firmware on the

two controllers is compared. If the versions are mismatched, the system prompts to clone the

firmware on the controller with the latest version (higher number) over to the controller with

the earlier version (lower number) firmware. The following message is displayed on the LCD

panel of the controller with the earlier firmware:

07 CLONE FIRMWARE? ‘<‘= NO, ‘>’= YES

Press the

button on the LCD panel to clone the firmware. In dual-controller configurations,

the firmware on the controllers

must

be the same version.

Press the ^ and v LCD panel message buttons on the front of each MSA controller to review the

startup messages and look for the following message:

Startup Complete

NOTE:

Proceed to the next step only after the

Startup Complete

message is displayed. If

you power on (or restart) the server before the MSA array completes its start-up sequence, the

server may not properly discover the storage.

Power on the servers in the SAN with access to the MSA, start the operating system, and log on

as a user with administrative control.