HP BL680c ProLiant BL680c Generation 5 Server Blade User Guide - Page 15

Install the access panel, Remove the FBDIMM baffle

Get HP BL680c - ProLiant - G5 PDF manuals and user guides
UPC - 884420396314
View all HP BL680c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Install the access panel 1. Place the access panel on top of the server blade with the hood latch open. Allow the panel to extend past the rear of the server blade approximately 0.8 cm (0.2 in). 2. Engage the anchoring pin with the corresponding hole in the latch. 3. Push down on the hood latch. The access panel slides to a closed position. Remove the FBDIMM baffle CAUTION: To avoid damage to the server blade and the enclosure, install all FBDIMM baffles in the proper location after adding or replacing FBDIMMs. FBDIMM baffles that are missing or installed incorrectly can compromise server blade and enclosure cooling. To remove the component: 1. Power down the server blade (on page 13). 2. Remove the server blade (on page 14). 3. Remove the access panel (on page 14). 4. Remove the FBDIMM baffle: o FBDIMM baffle covering FBDIMM slots 1-8 Operations 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Operations 15
Install the access panel
1.
Place the access panel on top of the server blade with the hood latch open. Allow the panel to
extend past the rear of the server blade approximately 0.8 cm (0.2 in).
2.
Engage the anchoring pin with the corresponding hole in the latch.
3.
Push down on the hood latch. The access panel slides to a closed position.
Remove the FBDIMM baffle
CAUTION:
To avoid damage to the server blade and the enclosure, install all FBDIMM baffles
in the proper location after adding or replacing FBDIMMs. FBDIMM baffles that are missing or
installed incorrectly can compromise server blade and enclosure cooling.
To remove the component:
1.
Power down the server blade (on page
13
).
2.
Remove the server blade (on page
14
).
3.
Remove the access panel (on page
14
).
4.
Remove the FBDIMM baffle:
o
FBDIMM baffle covering FBDIMM slots 1-8