HP Cisco MDS 9120 Cisco MDS 9100 Series Hardware Installation Guide (OL-17951- - Page 80

Installing the Switch on the Shelf Brackets, Regulatory Compliance and Safety

Get HP Cisco MDS 9120 - Fabric Switch PDF manuals and user guides View all HP Cisco MDS 9120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Cisco MDS 9000 Family Telco and EIA Shelf Bracket Appendix A Cabinet and Rack Installation Send documentation comments to [email protected] Step 4 Step 5 Attach the crossbar to the shelf brackets as shown in Figure A-2, using the 10-32 screws. Insert the slider rails into the shelf brackets as shown in Figure A-2. Then attach them to the rear rack-mounting rails using a minimum of four 12-24 or 10-24 screws. Installing the Switch on the Shelf Brackets This section provides general instructions for installing the switch on top of the shelf brackets. For detailed installation instructions, see the "Installing the Switch in a Cabinet or Rack" section on page 2-5. Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Note Before you install, operate, or service the system, refer to the Regulatory Compliance and Safety Information for the Cisco MDS 9000 Family for important safety information. To install the switch on top of the shelf brackets, follow these steps: Step 1 Step 2 Step 3 Verify that the shelf brackets are level and securely attached to the rack-mounting rails, the crossbar is securely attached to the shelf brackets, and the rack is stabilized. Slide the switch onto the shelf brackets, ensuring that it is squarely positioned. Attach the switch to the rack-mounting rails. See the "Installing the Switch in a Cabinet or Rack" section on page 2-5. Caution We recommend grounding the chassis, even if the rack is already grounded. A grounding pad with two threaded M4 holes is provided on the chassis for attaching a grounding lug. Note The grounding lug must be NRTL listed and compatible with copper conductors. Only copper conductors (wires) must be used and the copper conductor must comply with National Electrical Code (NEC) for ampacity. Cisco MDS 9100 Series Hardware Installation Guide A-8 OL-17951-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Send documentation comments to [email protected]
A-8
Cisco MDS 9100 Series Hardware Installation Guide
OL-17951-02
Appendix A
Cabinet and Rack Installation
Cisco MDS 9000 Family Telco and EIA Shelf Bracket
Step 4
Attach the crossbar to the shelf brackets as shown in
Figure A-2
, using the 10-32 screws.
Step 5
Insert the slider rails into the shelf brackets as shown in
Figure A-2
. Then attach them to the rear
rack-mounting rails using a minimum of four 12-24 or 10-24 screws.
Installing the Switch on the Shelf Brackets
This section provides general instructions for installing the switch on top of the shelf brackets. For
detailed installation instructions, see the
“Installing the Switch in a Cabinet or Rack” section on
page 2-5
.
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Note
Before you install, operate, or service the system, refer to the
Regulatory Compliance and Safety
Information for the Cisco MDS 9000 Family
for important safety information.
To install the switch on top of the shelf brackets, follow these steps:
Step 1
Verify that the shelf brackets are level and securely attached to the rack-mounting rails, the crossbar is
securely attached to the shelf brackets, and the rack is stabilized.
Step 2
Slide the switch onto the shelf brackets, ensuring that it is squarely positioned.
Step 3
Attach the switch to the rack-mounting rails. See the
“Installing the Switch in a Cabinet or Rack” section
on page 2-5
.
Caution
We recommend grounding the chassis, even if the rack is already grounded. A grounding pad with two
threaded M4 holes is provided on the chassis for attaching a grounding lug.
Note
The grounding lug must be NRTL listed and compatible with copper conductors. Only copper conductors
(wires) must be used and the copper conductor must comply with National Electrical Code (NEC) for
ampacity.