HP Cisco MDS 9216A Cisco MDS 9000 Family System Messages Reference (OL-15956-0
HP Cisco MDS 9216A - Fabric Switch Manual
View all HP Cisco MDS 9216A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Cisco MDS 9216A manual content summary:
- HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 1
Send documentation comments to [email protected] Cisco MDS 9000 Family System Messages Reference Cisco MDS 9000 SAN-OS Release 3.3(1a) April 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS ( - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 2
DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 3
Problems in Cisco Products xx Obtaining Technical Assistance xxi Cisco Technical Support & Documentation Website xxi Submitting a Service Request xxi Definitions of Service Request Severity xxii Obtaining Additional Publications and Information xxii Introduction to System Messages for the Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 4
Contents Send documentation comments to [email protected] 2 C H A P T E R System Messages and Recovery Procedures for the Cisco MDS 9000 Family 2-1 AAA Messages 2-4 AAA-1 2-4 AAA-2 2-5 AAA-3 2-5 AAA-6 2-5 ACL Messages 2-5 ACL-2 2-6 ACL-4 2-8 ACL-5 2-8 ACL-6 2-8 ACLTCAM Messages 2-10 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 5
Contents Send documentation comments to [email protected] OL-15956-01 CIMSRVPROV-3 2-32 CIMSRVPROV-6 2-33 CLOUD Messages 2-33 CLOUD-2 2-33 CLOUD-3 2- -SLOT#-2 2-62 FC-TUNNEL Messages 2-63 FC-TUNNEL-3 2-63 FC-TUNNEL-5 2-65 FCC Messages 2-65 Cisco MDS 9000 Family System Messages Reference iii - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 6
Contents Send documentation comments to [email protected] FCC-2 2-65 FCC-5 2-66 FCC-6 2-67 FCC_LC Messages 2-67 FCC_LC-2 2-67 FCC_LC-5 2-94 FCMPLS-2 2-94 FCMPLS-3 2-95 FCMPLS-5 2-96 FCMPLS-6 2-96 FCNS Messages 2-97 FCNS-2 2-97 Cisco MDS 9000 Family System Messages Reference iv OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 7
Contents Send documentation comments to [email protected] OL-15956-01 FCNS-3 2-98 FCNS-6 2-99 FCS Messages 2-100 FCS-2 2-100 FCS 2-122 IKE-3 2-122 IKE-4 2-123 IKE-6 2-124 ILC_HELPER Messages 2-125 ILC_HELPER-2 2-125 ILC_HELPER-3 2-125 Cisco MDS 9000 Family System Messages Reference v - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 8
Contents Send documentation comments to [email protected] ILC_HELPER-6 2-125 ILC-SPAN Messages 2-125 ILC-SPAN-3 2-126 IMAGE_DNLD Messages IPS_SB_MGR-SLOT#-6 2-156 IPsec Messages 2-157 IPsec-2 2-157 IPsec-3 2-158 IPsec-5 2-158 Cisco MDS 9000 Family System Messages Reference vi OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 9
Contents Send documentation comments to [email protected] OL-15956-01 IPsec-6 2-159 IPsec-7 2-160 ISAPI Messages 2-160 ISAPI-SLOT#-0 2-160 Messages 2-191 LICMGR-2 2-191 LICMGR-3 2-192 LICMGR-6 2-194 MAC Messages 2-195 MAC-SLOT#-2 2-195 Cisco MDS 9000 Family System Messages Reference vii - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 10
Contents Send documentation comments to [email protected] MCAST Messages 2-196 MCAST-2 2-196 MCAST-4 2-196 MCAST-5 2-196 MODULE Messages -5 2-229 PLATFORM-7 2-232 PLOG Messages 2-232 PLOG-4 2-232 PLOG_SUP Messages 2-232 Cisco MDS 9000 Family System Messages Reference viii OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 11
Contents Send documentation comments to [email protected] OL-15956-01 PLOG_SUP-4 2-233 PORT Messages 2-233 PORT-3 2-233 PORT-5 2-233 2-277 RADIUS Messages 2-280 RADIUS-2 2-280 RADIUS-3 2-280 RADIUS-6 2-280 RDL Messages 2-282 RDL-3 2-282 Cisco MDS 9000 Family System Messages Reference ix - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 12
Contents Send documentation comments to [email protected] RDL-6 2-283 RIB Messages 2-284 RIB-0 2-284 RIB-1 2-284 RIB-2 2-284 RIB-3 2- 2-300 SECURITYD-3 2-301 SECURITYD-6 2-301 SENSOR Messages 2-302 SENSOR-2 2-302 SENSOR-3 2-303 Cisco MDS 9000 Family System Messages Reference x OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 13
Contents Send documentation comments to [email protected] OL-15956-01 SENSOR-5 2-304 SENSOR_USD Messages 2-304 SENSOR_USD-2 2-304 SENSOR_USD-3 2-359 SVC_BATTERY-SLOT#-4 2-361 SVC_BATTERY-SLOT#-6 2-361 SYSMGR Messages 2-362 SYSMGR-2 2-362 Cisco MDS 9000 Family System Messages Reference xi - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 14
Contents Send documentation comments to [email protected] SYSMGR-3 2-379 SYSMGR-4 2-386 SYSMGR-5 2-388 SYSMGR-6 2-394 SYSMGR-7 2-395 SYSTEMHEALTH SLOT#-5 2-428 VFC Messages 2-429 VFC-3 2-429 VHBAD Messages 2-430 VHBAD-2 2-430 Cisco MDS 9000 Family System Messages Reference xii OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 15
Contents Send documentation comments to [email protected] OL-15956-01 VHBAD-3 2-431 VHBAD-7 2-433 VNI Messages 2-434 VNI-2 2-434 VNI-3 2- 2-449 VSHD-4 2-450 VSHD-5 2-451 VSHD-7 2-451 WWN Messages 2-452 WWN-1 2-452 WWN-2 2-452 WWN-3 2-454 Cisco MDS 9000 Family System Messages Reference xiii - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 16
XBAR-5 2-459 XBAR_CLIENT Messages 2-462 XBAR_CLIENT-2 2-462 XBAR_CLIENT-3 2-463 ZONE Messages 2-464 ZONE-2 2-464 ZONE-3 2-473 ZONE-4 2-474 ZONE-5 2-476 ZONE-6 2-477 DISK FAILURE CODES A-1 Cisco MDS 9000 Family System Messages Reference xiv OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 17
changed features supported by messages described in this version of the Cisco MDS 9000 Family System Messages Reference. For more information about a specific feature, refer to the Cisco MDS 9000 Family CLI Configuration Guide and Cisco MDS 9000 Family Fabric Manager Configuration Guide. New and - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 18
Supports intelligent linecard helper messages. Supports NASB messages.. Incremental messages added to IPSEC and DPVM. BIOS_DAEMON Supports BIOS_DAEMON messages. Cisco Fabric Services (CFS) Supports "System Messages and Recovery Procedures for the Cisco MDS 9000 Family" section on page 2-1 2.0(1b - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 19
Supports IKE messages. IP security (IPSEC) Supports IPSEC messages. Resource Supports RM messages. management (RM) SFC Supports SFC messages. SCSI targets Supports SCSI-TARGET messages. VFC Supports " section on page 2-306 OL-15956-01 Cisco MDS 9000 Family System Messages Reference xxvii - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 20
New and Changed Information Send documentation comments to [email protected] xxviii Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 21
the system messages for the Cisco MDS 9000 Family of directors and multilayer fabric switches. The system software sends these messages to the console (and, optionally, to a logging server on another system) during operation. Not all messages indicate a problem with your system. Some messages - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 22
screen font Terminal sessions and information the switch displays are in screen font. boldface manual. Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Related Documentation The documentation set for the Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 23
Guide • Cisco MDS 9020 Fabric Switch Hardware Installation Guide Cisco Fabric Manager • Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide • Cisco MDS 9000 Family Fabric Manager Configuration Guide • Cisco MDS 9000 Fabric Manager Online Help • Cisco MDS 9000 Fabric Manager Web Services - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 24
Configuration Guide • Cisco MDS 9000 Family Secure Erase Configuration Guide- For Cisco MDS 9500 and 9200 Series Troubleshooting and Reference • Cisco MDS 9000 Family Troubleshooting Guide • Cisco MDS 9000 Family MIB Quick Reference • Cisco MDS 9020 Fabric Switch MIB Quick Reference • Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 25
access multiple versions of installation, configuration, and command guides for Cisco hardware and software products. With the DVD, you the Cisco Marketplace at this URL: http://www.cisco.com/go/marketplace/ Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m. - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 26
is found at this URL: http://www.cisco.com/en/US/products/products_psirt_rss_feed.html Reporting Security Problems in Cisco Products Cisco is committed to delivering secure products. We test to find other means of encrypting the data. Cisco MDS 9000 Family System Messages Reference xx OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 27
you do not have a valid Cisco service contract, contact your reseller. Cisco Technical Support & Documentation Website The Cisco Technical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 28
network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL: http://www.cisco.com/packet xxii Cisco MDS 9000 Family System Messages - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 29
You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj • Networking products offered by Cisco Systems, as well as customer support services, can be obtained at this URL: http://www.cisco.com/en/US/products/index.html • Networking Professionals Connection is an interactive - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 30
Preface Send documentation comments to [email protected] xxiv Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 31
-113 %PORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver for interface fc1/13 is not supported . Warning System Log Message Format Description Element month dd hh: switch The facility of the error or event (daemon, kernel, VSHD, or other facility) OL-15956-01 Cisco MDS 9000 Family System Messages - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 32
System Log Message Format Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family Send documentation comments to [email protected] Warning System Log Message Format Description (continued) Element severity MNEMONIC %$VSAN #%$ description Description Single-digit code - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 33
System Messages for the Cisco MDS 9000 Family System Log Message Format Send documentation comments to [email protected] The following example system message shows how the variable field might be used: %MODULE-5-MOD_MINORSWFAIL: Module [dec] reported a failure in service [chars] In this - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 34
notification) Alarm/event code= SYSTEM_MSG Description of the problem= Authpriv [dec] reported a failure in service [chars] [dec] is the module slot number appear (refer to the Cisco MDS 9000 Family CLI Configuration Guide and the Cisco MDS 9000 Family Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 35
Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family Capturing System Messages and History Send documentation comments to [email protected] Fabric Manager Configuration Guide). Only system messages that correspond to the configured logging level or higher severity - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 36
Capturing System Messages and History Chapter 1 Introduction to System Messages for the Cisco MDS 9000 Family Send documentation comments to [email protected] Cisco MDS 9000 Family System Messages Reference 1-6 OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 37
H A P T E R System Messages and Recovery Procedures for the Cisco MDS 9000 Family OL-15956-01 This chapter lists messages according to the same , page 2-45 • DSTATS Messages, page 2-48 • EPP Messages, page 2-50 • ETHPORT Messages, page 2-51 Cisco MDS 9000 Family System Messages Reference 2-1 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 38
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] • EXCEPTIONLOG Messages, page 2-62 • FC-TUNNEL Messages, page 2-63 • FCC Messages, page 2-65 • FCC_LC Messages, page 2-67 • FCD Messages, page 2-69 • FCDD Messages - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 39
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] • LICMGR Messages, page 2-191 • MAC Messages, page 2-195 • MODULE Messages, page 2-197 • NASB Messages, page 2-204 • NPC Messages, page 2-205 • NPV Messages, page - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 40
for concurrent AAA sessions was reached. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Cisco MDS 9000 Family System Messages Reference 2-4 OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 41
of a problem with NVRAM. The problem is described in the error message. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 42
Initialization failed for the ACL because of the reason shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ACL-2-ACL_LINECARD_STATUS: Status from linecard: [dec], for module: [chars](ID: [dec]), status : [dec], error_id - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 43
]. Explanation There was a mismatch in the persistent storage service (PSS) version. The persistent storage service (PSS) service has a different version number than the expected version number. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ACL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 44
addressable memory (TCAM) operation failed because of the reason shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). ACL-4 ACL-5 Error Message ACL-4-ACL_WARNING: [chars] [dec]. Explanation This message shows the details of an ACL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 45
] [chars]. Explanation This message reports the ACL N port or NL port event status. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ACL-6-ACL_PORT_MODE_EVENT_STATUS: [chars] [chars]. Explanation This message reports the ACL port mode event status - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 46
] [chars]. Explanation This message reports the ACL update SSRAM for QoS event status. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). ACLTCAM Messages This section contains the access control list ternary content addressable memory (ACLTCAM) messages. ACLTCAM - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 47
shown in the error message. Recommended Action Restart the process. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message ACLTCAM-2-ACL_TCAM_MTS_FAILURE: MTS operation failed: [chars]. Explanation The messaging and transaction service (MTS) operation failed because of the reason shown in the - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 48
failed for opCode: [dec]. Explanation The messaging and transaction service (MTS) registration failed for the reason shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ACLTCAM-2-ACL_TCAM_NO_ROUTE: ACLTCAM failed - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 49
storage service (PSS) operation because of the reason shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN- also shows the error code for this problem. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 50
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). 2-14 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 51
Support. Introduced Cisco MDS SAN-OS Release 3.0(1). BOOTVAR Messages This section contains the boot variable (BOOTVAR) messages. BOOTVAR-2 Error Message BOOTVAR-2-ALLOC_MEMORY: Memory allocation failed. Explanation The service failed to allocate memory. Recommended Action Check to see if the switch - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 52
again. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 1.2(2a). Cisco MDS SAN-OS Release 3.0(1). Error Message BOOTVAR-3-INIT_FAILED: Initialization failed: Component [chars]. Explanation The service failed - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 53
during auto-sync. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 3.0(1). Error Message BOOTVAR-3-NEIGHBOR_REJECT_AUTOCOPY: auto-copy failed - not supported by neighbor supervisor. Explanation The standby supervisor does not - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 54
have the image on the flash before reboot. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by opposing supervisor, starting... Explanation The standby supervisor supports automatic copy. Automatic copy has started. Recommended Action - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 55
. Explanation The service has successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release commands or Cisco Fabric Manager procedures to get more information about the error. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 Family - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 56
for the failure of the CFS operation and rectify the problem. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message CALLHOME-3-CALLHOME_CFS_OPERATION_FAILED: [chars] : [chars]. Explanation The Call Home operation using Cisco Fabric Services (CFS) failed because of the reason shown in the error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 57
. If Call Home was not enabled, use either CLI commands or Fabric Manager procedures to get more information about the error. Introduced Cisco MDS SAN-OS Release 1.2(2a). CDP Messages This section contains the Cisco Discovery Protocol (CDP) messages. CDP-2 CDP-3 Error Message CDP-2-INITFAIL: CDP - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 58
for the failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message CDP-3-MTSERROR: [chars]. Explanation The Cisco Discovery Protocol daemon encountered a messaging and transaction service (MTS) error. The error message shows the context where the - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 59
a raw socket. The error message identifies the interface and the reason for this failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). CDP-6 Error Message CDP-3-SOCKOPENFAIL: Failed to open socket for receiving raw 802_2 packets - [chars]. Explanation An - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 60
certificate enrollment exited. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message CERT_ENROLL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 61
]. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message CFS-2-CFS_REJECT: CFS reject: [chars]: Switch WWN [chars], reason [chars]. Explanation When Cisco Fabric Service (CFS) receives a malformed CFS packet from a switch with WWN and IP address shown in - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 62
. Explanation The Cisco Fabric Services could not allocate memory. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 63
CFS-3-MERGE_FAILED: Merge failed for app [chars], local switch wwn [chars],ip [chars], remote switch wwn [chars], ip [chars]. Explanation The Cisco Fabric Services has detected a merge failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). OL-15956-01 Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 64
2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message CFS-3-GENERROR: [chars]. Explanation The Cisco Fabric Services encountered a general error, one that does not - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 65
been translated to the new format. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message CFS-6-BECAME_ACTIVE: Became ACTIVE from standby mode. Explanation The Cisco Fabric Services on the standby supervisor became active and it is ready to serve client - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 66
to send a heartbeat message to the system manager. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message CFS-6-GENERAL_EVENT: [chars]. Explanation The Cisco Fabric Services generated an event. The description of the event is shown in the error message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 67
down gracefully. Recommended Action This is an informational message. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message CFS-6-SWITCHOVER: Switching Over to other Sup. Explanation The Cisco Fabric Services successfully switched over to the standby supervisor. Recommended Action No action is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 68
: Source URI:[chars] Destination URI:[chars] errcode:[dec]. Explanation A persistent storage service (PSS) snapshot error occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message CIMSRVPROV-2-CIM_SYSLOG_SDWRAP_ERR: Description:[chars] errcode:[dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 69
Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.0(1). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 70
error. Recommended Action Check the message for the reason for failure of the CFS operation and rectify the problem. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message CLOUD-3-CLOUD_PSS_OPERATION_FAILED: [chars] : [chars]. Explanation PSS operation failed Recommended Action Check the message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 71
started. Get more information using the cloud-discovery status CLI command. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 3.0(1). CORE-DMON Messages This section contains the core dump daemon (CORE-DMON - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 72
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] Introduced Cisco MDS SAN-OS Release 3.0(1). 2-36 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 73
Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 74
a remote switch was rejected. The error message indicates the reason for failure. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 75
-alias database with the other switches in the fabric. Resolve any conflicts and commit the changes. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message DEVICE-ALIAS-3-MTS_OPER_FAILED: [chars]. Explanation An error occurred during a messaging and transaction service (MTS) operation. The error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 76
the persistent storage service (PSS) operation and the reason for failure. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 77
has port WWN based members and issue the import command again. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message DEVICE-ALIAS-6-IMPORT_NAME_CONFLICT: Fcalias [chars] could not be imported - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 78
information regarding failure. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). DEV_LOG Messages This section - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 79
Explanation A new N port has come up, which is zoned in the same zone as the server. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message DMM-SLOT#-5-LOG_ERR_DMM_NEW_NPORT_STG_ZONE: Job Id:%Ld VSAN :[dec] New N-Port FCID :[hex] Storage FCID:[hex] are in - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 80
the suspension of data migrationjob because of in IP connectivity to the peer SSM. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message DMM-SLOT#-5-LOG_EV_DMM_JOB_START: Job Id:%Ld NumSession:[dec]. Explanation Event indicating the start of a data - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 81
Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 82
. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message DPVM-3-DDAS_MODE_INVALID: [chars]. Explanation The Distributing Devise Alias Services (DDAS) mode is invalid when you merge two switches that have - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 83
the persistent storage service (PSS) operation that caused the error. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 84
storage service (PSS) because of the reason shown in the error message. Recommended Action Enter the show flash command or use a similar Fabric Manager/Device Manager procedure to collect more information. See PSS system error codes in the output for the cause of the PSS error. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 85
the output for the cause of the PSS error. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message DSTATS-3-PSS_MAX_VALUE_FAIL: pss set runtime max value failed due to error: [hex]. Explanation DSTATS failed to set the persistent storage service (PSS) runtime max value because of the reason shown - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 86
Recommended Action Enter the show flash command or use a similar Fabric Manager/Device Manager procedure to collect more information. See PSS system error codes in the output for the cause of the PSS error. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message DSTATS-3-PSS_STORE_FAIL: pss store - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 87
Action Enter the show flash command or use a similar Fabric Manager/Device Manager procedure to determine which transceiver is being used. Contact customer support for a list of authorized transceiver vendors. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_ADMIN_DOWN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 88
down. Recommended Action Enter the no shutdown command or use a similar Fabric Manager/Device Manager procedure on the PortChannel that the interface belongs to. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_CHANNEL_MEMBERSHIP_UPDATE_IN_PROGRESS: Interface [chars] is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 89
the interface. Recommended Action Enter show port internal info and check the status in the ELP failure reason field. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_EPP_FAILURE: Interface [chars] is down (Error Disabled - EPP Failure). Explanation Trunk protocol failed - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 90
recover using a shutdown followed by a no shutdown Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_ESC_FAILURE_ISOLATION: Interface [chars] is down (Isolation due to ESC failure). Explanation Exchange switch parameters (ESC) failed on the interface. Recommended Action - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 91
on this interface. Recommended Action Enter a show port internal info to determine the list of modes supported on this interface. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_INCOMPATIBLE_ADMIN_RXBBCREDIT: Interface [chars] is down (Error disabled - Incompatible admin - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 92
on this interface. Recommended Action Enter show port internal info to determine the range of speed supported on this interface. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_INITIALIZING: Interface [chars] is down (Initializing). Explanation The interface is in - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 93
. Recommended Action Check the connectivity of this interface and ensure that it is connected to another switch. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_MODULE_REMOVED: Interface [chars] is down (module removed). Explanation Interface is down because the module - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 94
the same and enter the shutdown and then no shutdown commands. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_RCF_IN_PROGRESS: Interface [chars] is down (RCF in progress - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 95
The software servicing the data path on the port has failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 96
connected to the same remote switch as all the other interfaces in the PortChannel. Introduced Cisco MDS SAN-OS Release 1.2(2a). can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 1.2(2a). 2-60 Cisco MDS 9000 Family - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 97
. Enter traceroute [ipaddr] to check the connectivity to the peer. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_DOWN_TCP_PERSIST_TIMER_EXPIRED: Interface [chars] is down(TCP - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 98
[chars], VSAN [chars] is up. Explanation The interface is trunking and the VSAN is up. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ETHPORT-5-IF_UP: Interface [chars] is up [chars]. Explanation Interface is up. If applicable, the mode is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 99
process unsuccessfully tried to send a messaging and transaction service (MTS) message. The messaging and transaction service (MTS) error number is shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FC-TUNNEL-3-NS_ERROR - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 100
system error code. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FC-TUNNEL-3-PSS_ERROR: PSS operation [chars] returned error: [hex]. Explanation A persistent storage service operation failed. The error message shows the context where the failure - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 101
Explanation FC MPLS tunnel process received unexpected messaging and transaction service (MTS) event. The error message shows the messaging and transaction service (MTS) opcode. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FC-TUNNEL-5 Error Message FC-TUNNEL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 102
: FCC has been disabled. Explanation The Fibre Channel Congestion Control process has been disabled. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCC-5-ENABLE: FCC has been enabled. Explanation The Fibre Channel Congestion Control process has - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 103
with priority greater than or equal to the threshold shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FCC_LC Messages This section contains the Fibre Channel Congestion Control line card (FCC_LC) messages. FCC_LC-2 Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 104
disabled. Explanation The Fibre Channel Congestion Control line card process has been disabled. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message FCC_LC-5-ENABLE: FCC_LC has been enabled. Explanation The Fibre Channel Congestion Control line card - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 105
packets with priority less than or equal to the threshold shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). FCD Messages This section contains the FICON control device (FCD) messages. FCD-7 Error Message FCD-7-SB3_ABTS_EXCHANGE: sb3 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 106
Explanation Illegal event received in twilight zone remover finite state machine (FSM). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDD-SLOT#-5-LOG_FCDD_VCONF_FSM: [chars]. Explanation Illegal event received in VSAN configuration finite state - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 107
]. Explanation Illegal event received in VSAN normal operation finite state machine (FSM). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FCDD-SLOT#-7 Error Message FCDD-SLOT#-7-LOG_FCDD_DEBUG: [chars]. Explanation Unexpected errors that affect some normal - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 108
SLOT#-5-LOG_FCDDH_NOTICE: [chars]. Explanation Major configuration changes occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). FCDDH Messages This section contains the Fibre Channel device discovery helper FCDDH - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 109
have the same WWN and change one to a unique WWN. Then change the domain ID for one of the switches. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message FCDOMAIN-2-EPORT_ALREADY_ISOLATED: Interface [chars] is down - VSAN [dec]. Explanation The domain manager was going to isolate the interface - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 110
is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-2-FC2BIND_FAILED: Bind to FC2 Service failed. Explanation The domain manager has not been able to contact the FC2 module. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 111
the domain manager. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-2-MTSBIND_FAILED - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 112
use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-2-SDWRAPBIND_FAILED: Bind to Debug Server failed. Explanation The domain manager has not been able to contact the history debug service. Any problems - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 113
the Cisco MDS 9000 Family Send documentation comments to [email protected] Error Message FCDOMAIN-2-SYSBIND_FAILED: Bind to System Manager service failed same principal switch and are connected in the same logical fabric. Recommended Action No action is required. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 114
domain manager has not been able to send a message to the message transactional service (MTS). Recommended Action Execute a nondisruptive fcdomain restart in the affected VSAN. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-3-MTSSENDREQ_FAILED: IPC failure (sending of a request - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 115
history service. Any problems occurring in the fcdomain feature will not be logged to this debug history. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message FCDOMAIN-3-VSAN_MERGE_DETECTED: Merge detected with VSAN [dec] (Common Fabric Name [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 116
when fcdomain distribution is enabled. Discard the current session on the local switch and start a new one on the principal switch. Introduced Cisco MDS SAN-OS Release 3.0(2). Error Message FCDOMAIN-4-FABRICCONFSTARTRCF: Disruptive reconfiguration started. Explanation A disruptive reconfiguration - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 117
to purge stale entries and to obtain more free entries. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Error Message FCDOMAIN-5-PSWSSTARTED: Principal Switch Selection started - VSAN [dec]. Explanation The principal switch selection has started for the VSAN shown in the error message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 118
SAN-OS Release 3.0(1). FCDOMAIN-6 Error Message FCDOMAIN-6-BF_STARTED: BF started by [chars]. Explanation A build fabric has started in this VSAN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(2). 2-82 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 119
: Upstream interface has been fast-switched from [chars] to [chars]. Explanation The upstream interface has been fast-switched because of a link failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(2) OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 120
VSAN has started. This can happen when two or more fabrics merge, or when the user manually triggers a nondisruptive reconfiguration of the VSAN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). 2-84 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 121
Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-6-FABRICNAME_VALID: Fabric name [chars] available. Explanation Fabric name is available. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 122
be invalidated. Recommended Action Use the CLI or Fabric Manager/Device Manager to configure the domain ID type as static in an existing VSAN. On the CLI, enter the fcdomain domain static vsan [vsan-id] command. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message FCDOMAIN-6-FCIDS_ASSIGNED - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 123
An FC ID was requested with type 00.00.YY, but specified an entire area. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-6-MY_NON_VIRTUAL_DOM_CONFLICTS: During VSAN merge detected that the local switch has the same domain ID [dec] and - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 124
Selection started. Explanation A principal switch selection (PSwS phase) has started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message FCDOMAIN-6-RCF_STARTED: RCF started by [chars]. Explanation A fabric reconfiguration has started in this VSAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 125
the same WWN but different non-virtual domain IDs. Recommended Action Check which switches have the same WWN and change either one. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message FCDOMAIN-6-TIMER_UNKNOWN: fcdomain has received a notification for an unknown timer expiration. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 126
virtual domain ID on the local VSAN and the domain IDs on the remote VSAN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message FCDOMAIN-6-UUIDNOSPACEFOUND: No available space to store the identity of the requestor the FCIDs. Explanation No available - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 127
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 Family System Messages Reference 2-91 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 128
to the VSAN. Explanation There may be a problem in the sequence that shuts down all interfaces before fcdomain receives a request from FICON manager to purge the persistent FC ID table. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message FCDOMAIN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 129
been used. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCDOMAIN-7-PSWSCOMPLETED: Principal Switch Selection completed (Fabric Name [chars]). Explanation The principal switch selection (PSwS phase) has completed. Recommended Action No action - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 130
-2-PROC_SHUTDOWN: daemon shutting down. Explanation FC MPLS process exited. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). Error Message FCMPLS-2-PROC_STARTING: daemon started in the [chars] mode. Explanation FC MPLS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 131
received unexpected messaging and transaction service (MTS) event. MTS opcode is specified in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). OL-15956-01 Cisco MDS 9000 Family System Messages - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 132
chars] is shutdown. Explanation Existing LDP session has been shut down. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). Error Message FCMPLS-6-FT_SEQ_ROLLOVER: Rolling over the local ft ack number. Explanation Fault - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 133
type is specified in hex.The error message describes the LDP peer. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). Error Message FCMPLS-6-UNKNOWN_TLV_RXED: Unknown LDP TLV: type 0x[hex], length [dec], is received from - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 134
FCNS-3 Error Message FCNS-2-RELOAD_FAILURE: : [chars]. Explanation Failed to reload information from persistent storage service( PSS). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCNS-3-BAD_FRAME: : [chars]. Explanation Received a bad frame - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 135
: [chars] [chars]. Explanation Failure occurred trying to do a messaging and transaction service messaging and transaction service (MTS) operation. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FCNS-6 Error Message FCNS-3-PSS_FAILURE: : [chars]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 136
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] FCS Messages This section contains the Fabric Configuration Server (FCS) messages. FCS-2 Error Message FCS-2-ALLOC_FAILED: Memory allocation failed for size:[dec]. - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 137
the PSS service, its current version number, and the expected version. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 138
of the messaging and transaction service (MTS) message. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 139
If this message is seen during a cold boot, it means that the queried module came up after Fabric Configuration Server (FCS) and this case can be ignored. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCS-6-INFORMATION: [chars]. Explanation An event happened that affects FCS. The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 140
). Explanation FC-SP manager is unable to initialize with the FC-2 E port infrastructure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FCSP-MGR-2-FC2_F_INIT_FAILED: Fibre-Channel Initialization of an F_Port failed ( [chars] ). Explanation FC-SP - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 141
Message FCSP-MGR-2-LICENSE_UNAVAILABLE: License:[chars] unavailable, service exiting. Explanation The license is unavailable. The FC-SP service will exit now. Recommended Action Install the license file to continue using the feature. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message FCSP-MGR - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 142
. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(2a). Deprecated Cisco MDS SAN-OS Release 1.3(4a). FDMI Messages This section contains the Fabric-Device Management Interface (FDMI) messages. 2-106 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 143
BAD_FRAME: Malformed frame received: [chars]. Explanation The Fabric-Device Management Interface (FDMI) process received malformed frame. The error message describes the problem. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FDMI-3-BAD_RESPONSE - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 144
and transaction service (MTS) opcode is specified in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FDMI-3-NO_RESPONSE: No response from switch whose domain id is [dec]. Explanation The Fabric-Device Management Interface - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 145
and transaction service (MTS) opcode is specified in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). FDMI-6 Error Message FDMI-4-SW_REJ_RESPONSE: Reject response [chars] from switch whose domain id is [dec]. Explanation The Fabric-Device - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 146
down: [chars]. Explanation FICON manager is shutting down. Recommended Action This is a severe error. Provide the reason given in the message to your customer service representative. Introduced Cisco MDS SAN-OS Release 1.3(1). 2-110 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 147
state can be removed or changed. Recommended Action Bring down the port and then change the assigned port number. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message FICON-3-E_ASSIGN_PROHIBIT_PN_FAIL: [chars]. Explanation Logical port address cannot be prohibited. Recommended Action Check port - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 148
dynamic connectivity mask (PDCM) for this port to bring the port up as an E or TE port in a FICON VSAN. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message FICON-3-E_UNASSIGN_NO_PN_FAIL: [chars]. Explanation Only port number already assigned can be removed. Recommended Action Check port - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 149
on the VSAN shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). FLOGI Messages This section contains the fabric login (FLOGI) messages. FLOGI-5 Error Message FLOGI-5-MSG_IF_REINIT_ALPA_CONFLICT: [VSAN [dec], Interface [chars]] FL/TL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 150
the error message. Recommended Action This is a severe problem. Provide the reason shown and the log files for Fabric Shortest Path First (FSPF) to your customer service representative. Introduced Cisco MDS SAN-OS Release 1.2(2a). 2-114 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 151
service representative.You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS problem. Provide the output of show fspf database to your customer service representative. You may need to power cycle the switch. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 152
fspf error CLI command to your customer service representative. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FSPF-3-LOCK_FAIL: FSPF failure in gaining lock. Explanation There is a problem with locking a shared resource between Fabric Shortest Path First (FSPF) threads. Recommended - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 153
debug fspf route CLI commands if the problem is reproducible. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message Fabric Shortest Path First (FSPF) threads. Recommended Action Provide the output of the debug fspf all CLI command to your customer support representative. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 154
output the of debug fspf event and debug fspf fc pkt CLI commands for the interfaces involved to your customer support representative. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FSPF-4-LSR_DROPPED: [chars], Dropping LSR [dec] received on interface [chars] in VSAN [dec]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 155
fc pkt and debug fspf event VSAN [dec] commands to your customer support representative. Introduced Cisco MDS SAN-OS Release 1.2(2a). FSPF-6 Error Message FSPF-5-STARTING: Routing daemon started. Explanation Fabric Shortest Path First (FSPF) routing daemon has been started. Recommended Action No - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 156
Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FSPF-6-INTF_OPER_DOWN: Down on interface [chars] in VSAN [dec]. Explanation Fabric will be deleted from all the connected switches. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 157
change. If the situation persists, the domain assignment of switches may not be unique. Recommended Action If this message is received continuously, check if the domain assignment is unique in the fabric. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message FSPF-6-STATE_CREATED: Internal - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 158
, IKE will exit. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message IKE-3-FIPS_MODE_ERROR: Could - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 159
found for peer [chars]. Explanation There is an IPsec policy mismatch for the peer. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message IKE-3-IKE_PROGRAM_EXIT: [chars]. Explanation The Internet Key Exchange (IKE) process experienced an abnormal exit - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 160
(IKE) received an invalid payload. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). IKE-6 Error Message IKE-4-UNSUPPORT: [chars] is not supported (message from [chars]). Explanation Internet Key Exchange (IKE) received something unsupported. Recommended - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 161
card will be rebooted. Recommended Action Install the appropriate SSE license so you can use the Storage Services Module (SSM) features. Introduced Cisco MDS SAN-OS Release 2.1(1a). ILC_HELPER-3 Error Message ILC_HELPER-3-INVALID_BOOTVAR: Invalid [chars] boot variable configured. The linecard will - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 162
Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS use a similar Fabric Manager/Device Manager procedure to download a new module image. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 163
verify the state of this module. Enter the install module CLI command or use a similar Fabric Manager/Device Manager procedure to retry the image download. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message IMAGE_DNLD-SLOT#-2-IMG_DNLD_FILE_SYSTEM_CHECK_ERROR: File System check failed: [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 164
has completed. The module should now be installing this new image. Recommended Action This message is informational only. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message IMAGE_DNLD-SLOT#-5-ADDON_IMG_DNLD_STARTED: Addon module image download process started. [chars]. Explanation The add - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 165
Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 166
access control list caused failures in other services. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). IPACL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 167
support this operation. Recommended Action Enter debug ipacl all, then recreate the operation scenario to find out more details. Introduced Cisco MDS the system is low on memory; if so reset the switch. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message IPCONF-3-FILE_WRITE_FAILED: Writing - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 168
[chars] has been deleted. Explanation The specified interface has been deleted. The service will delete all the configuration in that interface. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message IPCONF-6-INTERFACE_EVENT: IP address [chars] [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 169
Check if the system is low on memory and reset the switch if necessary. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message IPFC-3-INIT_FAILED: Initialization failed. Component [chars]. Explanation The service failed to start. The failure occurred while initializing the component shown - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 170
status. You can alternatively use Fabric Manager and/or Device Manager instead of the command line method. Introduced Cisco MDS SAN-OS Release 1.2(2a). Fiber Channel service started. Explanation The service successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 171
chars]. Explanation The IP service (IPS) initialization failed. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 172
got an ERA 35. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-3-FCIP_FTA_ERA_38: ERA 0x38 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 173
Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.0(1). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 174
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.0(1). 2-138 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 175
merging iSLB CFS fabrics. The reason for the failure is listed in the message. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 176
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.0(1). 2-140 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 177
iSLB zone set activation failed. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.0(1). IPS-4 Error Message IPS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 178
. Recommended Action Check the license state using either the CLI show license usage command or a similar Fabric Manager procedure. Acquire the necessary FCIP license. Introduced Cisco MDS SAN-OS Release 3.0(1). IPS-5 Error Message IPS-5-FCIP_BIND_FAILED: Bind failed for [chars] due to [chars] for - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 179
[hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [hex]. Explanation FCIP disbanded a group. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-5-FCIP_FTA_ERA_90: ERA 90 rcvd CH FCID: [hex] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 180
] CHI: [hex] CU FCID [hex] CUI: [hex] DA [hex] VSAN: [hex]. Explanation FCIP resigned a group. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-5-FCIP_FTA_RESP_3490: 3490 device discovered by FCIP CH FCID: [hex] CHI: [hex] device at CU FCID [hex - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 181
Non-Last VSAN, [chars] VSAN: [hex]. Explanation FTA was turned off for the non-last Vsan. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IPS-5-FCIP_FTA_TURN_ON: Turn ON FTA, [chars] VSAN: [hex]. Explanation FTA was turned on. Recommended Action No - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 182
in use. Explanation FCIP and iSCSI interfaces are trying to use the same local port. Recommended Action Use different ports. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message IPS-5-ISCSI_BAD_DATA_DIGEST_CRC: iSCSI ingress data digest error from initiator [chars] alias [chars] S_ID [hex] to - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 183
sessions were down during the last interval for the reason shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(2). Error Message IPS-5-ISCSI_CONN_UP: [chars]: iSCSI session up from initiator [chars] alias [chars] ip [chars] to target [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 184
match the configuration on the peer. Recommended Action Fix the FCIP write acceleration configuration to be consistent with the peer. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message IPS-5-IPS_IPACL_LOG_MSG: [chars]. Explanation The message lists details of the packet dropped due to ACLs - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 185
ip address for interface [chars]. Explanation Cannot configure IPS port IP address. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message IPS-5-SB_MGR_CORE_FAILED: Ethernet Processing core [chars] failed due to [chars]. Explanation Ethernet processing - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 186
mismatch. Explanation A special frame was received, and the source or destination fabric WWN does not match the local destination or source fabric WWN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message IPS-5-SFRAME_IF_ADMIN_DOWN: [chars]: special - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 187
The Internet Storage Name Service (iSNS) server returned an error for a register or deregister request. For select error codes, the ISNS client would retry and re-register all target nodes corresponding to the interface. Recommended Action No action is required. Cisco MDS 9000 Family System - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 188
directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(2a). Error Message IPS_SB_MGR-SLOT#-2-PORT_SOFTWARE_FAILURE: Port software failure, module [dec] port [dec]. Explanation The software servicing the data path on - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 189
purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(1). Deprecated Cisco MDS SAN-OS Release 1.3(2a). Error Message IPS_SB_MGR-SLOT#-2-SB1_REIMAGE_PREPARE_FAIL:Sibyte1 reimage disk formatting failed. Explanation There was a problem - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 190
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(2a). 2-154 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 191
line card. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(1). Deprecated Cisco MDS SAN-OS Release 1.3(2a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 192
line card. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(1). Deprecated Cisco MDS SAN-OS Release 1.3(2a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 193
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). IPsec Messages - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 194
or use a similar Fabric Manager/Device Manager procedure to collect drop statistics. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 195
IPsec is disabled because the license expired. Recommended Action Install an updated, valid license to continue using this feature. Introduced Cisco MDS SAN-OS Release 2.1(1a). IPsec-6 Error Message IPSEC-5-IPSEC_ENABLED: IPSec Enabled. Explanation IPsec is enabled. Recommended Action No action is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 196
chars]/[chars]. Explanation IPsec tunnel rekeyed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). ISAPI Messages This section contains the intelligent switch application programming interface (ISAPI) messages. ISAPI-SLOT#-0 Error Message ISAPI-SLOT#-0-ILC_EMERG - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 197
ISAPI-SLOT#-1 Error Message ISAPI-SLOT#-1-ILC_ALERT: [chars]. Explanation This is an intelligent switch API alert software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ISAPI-SLOT#-1-INVISTA_ALERT: [chars]. Explanation Isapi-invista - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 198
-OS Release 3.2(1). Error Message ISAPI-SLOT#-1-SSM_ALERT: [chars]. Explanation This is an intelligent switch API alert software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message ISAPI-SLOT#-1-SSM_ALERT: [chars]. Explanation Isapi software - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 199
ISAPI-SLOT#-3 Error Message ISAPI-SLOT#-3-ILC_ERROR: [chars]. Explanation This is an intelligent switch API error software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ISAPI-SLOT#-3-INVISTA_ERROR: [chars]. Explanation Isapi-invista - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 200
). ISAPI-SLOT#-4 Error Message ISAPI-SLOT#-4-ILC_WARN: [chars]. Explanation This is an intelligent switch API warning software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ISAPI-SLOT#-4-INVISTA_WARN: [chars]. Explanation Isapi-invista - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 201
ISAPI-SLOT#-5 Error Message ISAPI-SLOT#-5-ILC_NOTICE: [chars]. Explanation This is an intelligent switch API notice software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ISAPI-SLOT#-5-INVISTA_NOTICE: [chars]. Explanation Isapi-invista - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 202
). ISAPI-SLOT#-7 Error Message ISAPI-SLOT#-7-ILC_DEBUG: [chars]. Explanation This is an intelligent switch API debug software message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ISAPI-SLOT#-7-INVISTA_DEBUG: [chars]. Explanation Isapi-invista - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 203
Name Service (ISNS) initialization failed. ISNS is automatically restarted. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 204
happen if the Network Address Translation (NAT) mode is modified without completely deactivating the active inter-VSAN routing (IVR) zone set. Recommended Action Reboot the switch. Introduced Cisco MDS SAN-OS Release 2.1(1a). 2-168 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 205
range allowed for this interop mode. Refer to the Cisco MDS 9000 Family CLI Configuration Guide or Cisco MDS 9000 Family Fabric Manager Configuration Guide for details on the domain range limitations. Recommended Action Change the domain of the switch to which this IVR zone member is connected so - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 206
License required for continued IVR operation is not available. IVR is shutting down. Recommended Action Install the appropriate license for IVR services and then enable IVR again. Introduced Cisco MDS SAN-OS Release2.0(1b). 2-170 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 207
services within the shown seconds to continue uninterrupted operation. Introduced Cisco MDS switch) or not allowed because of the interop mode or allowed domain list configured. Recommended Action Verify that the configured virtual domain/FC ID is allowed and available for use. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 208
. Recommended Action If the problem persists, contact your support representative. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(2a - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 209
that the configuration is inconsistent in the fabric. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 210
if FICON is enabled on VSANs and native switch of device with port WWN is not present in the current active fabric binding database of those VSANs. This is a requirement for FICON compliance. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message IVR - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 211
range allowed for this interop mode. Refer to the Cisco MDS 9000 Family CLI Configuration Guide or Cisco MDS 9000 Family Fabric Manager Configuration Guide for details on the domain range limitations. Recommended Action Change the domain of the switch to which this IVR zone member is connected so - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 212
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). 2-176 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 213
purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message IVR-3-MTS_ERROR: MTS message transmission failed with error [dec]. Explanation IVR process unsuccessfully tried to send a messaging and transaction service (MTS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 214
of AFID/VSAN combination is more than the maximum supported value of 128, or (b) number of IVR-enabled switches is more than the maximum supported value of 128. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message IVR-3-UNEXPECTED_MTS_MSG: Unexpected - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 215
in the error message. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message IVR-3-VSAN_SEGMENTED - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 216
[chars]. Explanation The auto-topology update is discarded because of conflicts. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message IVR-4-FCID_REWRITE_REQUEST_TO_ACL_FAILED_AND_RETRYING: fcid rewrite [chars] request vsan [dec] did [chars] sid [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 217
. This switch has learned of a device that is a member of the active IVR zone, has the same domain ID, but belongs to another native VSAN.This device is not advertised in that VSAN until the native VSAN information is resolved. Recommended Action No action is required. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 218
. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(3). Error Message IVR-5-IVZS_WAITING_FOR_LOWEST_SWWN: Waiting for lowest switch WWN Inter-VSAN enabled switch in VSAN [dec]. Explanation This switch does not have the lowest switch world wide name (sWWN) in the VSAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 219
it is successful in all VSANs by entering the show ivr zone set status command or use a similar Fabric Manager/Device Manager procedure. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message IVR-5-LICENSE_CHECKIN_FAILED: Failed to checkin [chars] license: Err=[chars]. Explanation Failed to check - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 220
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message IVR-5-SERVICE_GROUP_ACTIVATED: Inter-VSAN Service Group has been activated. Explanation Inter-VSAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 221
is being made to resend the DRAV FSM frames. The details are shown in the message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message IVR-6-DRAV_DOMAIN_ALLOC: Virtual domain [dec] for Native AFID: [dec] Native VSAN [dec]. Explanation A virtual domain - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 222
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). 2-186 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 223
The line card switched port analyzer (LC-SPAN) manager encountered an error. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 224
chars]. Explanation General error in the PortChannel configuration. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 3.0(1). Error Message LC_PORT_CHANNEL-SLOT#-3-LC_PORT_CHANNEL_IDXMAP_FAILURE: could not lookup port index for - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 225
between two applications. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). LC_RDL Messages This section - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 226
: : [chars]. Explanation The line card remote domain lookup (LC_RDL) messaging and transaction service (MTS) errors occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). LC_RDL-6 Error Message LC_RDL-3-SYSLOG_MTS_REG_FAILED: : [dec] [dec]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 227
Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.1(1a). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 228
allowed. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(3). Deprecated Cisco MDS SAN-OS Release 1.3(4b). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 229
on the shown node and service access point (SAP). Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 230
command or use a similar Fabric Manager/Device Manager procedure to verify this license feature installation. Introduced Cisco MDS SAN-OS Release 1.3(4a switch is installed on another switch. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 231
Installed the named license file. Recommended Action Enter the show license command or use the similar Fabric Manager/Device Manager procedure to verify this license installation. Introduced Cisco MDS SAN-OS Release 1.3(4a). MAC Messages This section contains the MAC messages. MAC-SLOT#-2 Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 232
component cannot restart properly, contact your support representative. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). MCAST - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 233
Upgrade done message failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message MODULE-2-LCM_UPGRADE_READY_FAIL: Upgrade ready message or by using a similar Fabric Manager procedure. OL-15956-01 Cisco MDS 9000 Family System Messages Reference 2-197 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 234
all module command or by using a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message MODULE-2-MOD_MINORSWFAIL: Module [dec] reported a failure in service [chars]. Explanation A non-critical failure in the service occurred on the module. The module will not - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 235
by entering the show module internal all module CLI command or by using a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message MODULE-2-MOD_UNKNOWN: Module type [[dec]] in slot [dec] is not supported. Explanation The software card ID of module [dec] is not - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 236
the show module internal all xbar [decimaldigit] CLI command or by using a similar Fabric Manager procedure.' Introduced Cisco MDS SAN-OS Release 3.0(1). MODULE-3 Error Message MODULE-2-XBAR_UNKNOWN: Xbar type [[dec]] in slot [dec] is not supported. Explanation The software card ID of xbar is not - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 237
switch traffic. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message MODULE-5-MOD_MINORSWFAIL: Module [dec] reported a failure in service a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 Family - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 238
named is ready to be configured and to switch traffic. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message MODULE-5-MOD_OK module command or by using a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message MODULE - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 239
or by using a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 2.0(1b). Error Message MODULE-5-STANDBY_SUP_OK: Supervisor [dec] is standby. Explanation Module is ready to be configured and to switch traffic. Recommended Action No - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 240
DPP died. Explanation The data path processor (DPP) associated with the virtual target failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message NASB-SLOT#-5-LOG_ERR_TPC_VT_ACT_FAILED: VSAN :[dec] VT pWWN :[chars] VT Activate failed. Explanation The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 241
pWWN :[chars] VSAN down. Explanation The VSAN where the virtual target is configured is down. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). NPC Messages This section contains the N port creator (NPC) messages. NPC-SLOT#-3 Error Message NPC-SLOT#-3-LOG_NPC_ERR - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 242
could not disabled : [chars] [chars]. Explanation NPM could not be disabled due to the reason specified. Recommended Action Try again. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-2-NPV_EXITED Explanation NPM process exited in file error system logs. Recommended Action .No action is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 243
Message NPV-3-FC2_SEND_FAILED: [chars]. Explanation NPV process could send an FC2 message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-3-FRAME_DISCARDED: [chars]. Explanation NPV process discarded an FC2 frame. Recommended Action No action - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 244
.com Error Message NPV-3-LS_RJT_RCVD: [chars]. Explanation NPV process received an LS_RJT frame. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-3-MALLOC_FAILED: [chars]. Explanation An assertion failed in NPV code. Recommended Action No action - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 245
all frames received on a server interface or frames received from a specific port WWN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-6-LS_ACC_RCVD: [chars]. Explanation NPV process received an LS_ACC frame. Recommended Action No action is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 246
Release 3.2(1). Error Message NPV-6-FLOGI_RCVD Explanation NPV process received an FLOGI frame. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-6-LC_ACC_SENT Explanation NPV process sent a LS_ACC frame. Recommended Action No action is required - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 247
OS Release 3.2(1). Error Message NPV-6-MTS_REQ_RCVD Explanation NPV process received an MTS request. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). Error Message NPV-6-MTS_REQ_SENT Explanation NPV process received an MTS request. Recommended Action No action is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 248
.com Error Message NPV-6-SERVER_PROXY_LOGO_SENT Explanation NPV process sent a LOGO frame to core switch. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(1). NTP Messages This section contains the Network Time Protocol (NTP) messages. NTP-2 NTP-3 Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 249
NTP-6 Error Message NTP-3-NTP_SYSLOG_MTS_ERR: : [chars]. Explanation Network Time Protocol (NTP) messaging and transaction service (MTS) error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message NTP-6-NTP_SYSLOG_CREATED: : [chars]; Slot No: [dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 250
Error Message NVP-6-NVP_INFO: [chars]. Explanation virtual N port (NVP) daemon informational message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message NVP-6-STARTING: deamon started. Explanation The virtual N port (NVP) daemon successfully started - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 251
to collect more information or use a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-0-CHASSIS_CLKSW_MODULE_RESET: Modules reset due to clock switch. Explanation The chassis clock source has been switched and all Generation 1 line cards will be - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 252
threshold still exceeded. Recommended Action Enter the show env temperature CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-0-MOD_TEMPSHUTDOWN: Module [dec] powered down due to major - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 253
in the error message. Recommended Action Enter the show env temperature CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-0-SYS_SHUTDOWN: System shutdown in [dec] seconds due to major - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 254
and temperature alarms. Recommended Action Enter the show platform internal info CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message PLATFORM-1-FAN_FAIL: Fan module Failed. Explanation Fan module - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 255
env power CLI command or by using a similar Fabric Manager/Device Manager procedure. Refer to power supply documentation in the relevant hardware installation guide to learn how to increase power supply capacity. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-1-MDS9124_FAN_FAIL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 256
been removed. Recommended Action Enter the show platform internal info CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-2-CHASSIS_CLKMODOK: Chassis clock module [dec] ok. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 257
collect more information, or use a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message PLATFORM-2- least one exbar module has to be up for switch modules to function. Introduced Cisco MDS SAN-OS Release 3.0(1).' Error Message PLATFORM-2-MOD_PWRDENY: Module - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 258
temperature threshold. Recommended Action Enter the show env temperature CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-2-MOD_TEMPOK: [chars] recovered from minor temperature alarm - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 259
has been powered down because the card is not supported in this chassis. Recommended Action Use the show module CLI command to see the power down reason, or use a similar Fabric Manager procedure.' Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message PLATFORM-2-PFM_NETBOOT_DISABLE: Netboot for - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 260
EPLD can result in unexplained behaviour. Recommended Action Upgrade the power managment EPLD. Refer to the Cisco MDS 9000 Family CLI Configuration Guide. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message PLATFORM-2-PFM_STDBY_POWERUP_FAIL: standby supervisor failed to power up. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 261
service disruptions. Explanation Detected a power supply that has a different capacity than an the other power supply. Recommended Action Refer tot he Cisco MDS 9000 Family CLI Configuration Guide information, or use similar Fabric Manager procedures. Introduced Cisco MDS SAN-OS Release 3.0(1). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 262
Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS support representative to replace the unit. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-2-PS_UNKNOWN: Detected an unknown power supply [dec] for CISCO MDS 9500/9200 Multilayer Switches - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 263
CISCO MDS 9500/9200 Multilayer Switches (Serial number [chars]). Explanation This power supply is not supported for the Cisco MDS 9500 or 9200 series of switches. Recommended Action Refer to the appropriate product hardware installation guide similar Fabric Manager procedure. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 264
and show sprom xbar [dec] [dec] to read module IDPROM contents to collect more information (or use a similar Fabric Manager procedure). Introduced Cisco MDS SAN-OS Release 3.0(1). PLATFORM-4 Error Message PLATFORM-4-MOD_TEMPFAIL: [chars] temperature sensor [dec] failed. Explanation The module in the - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 265
] and show module internal all module [dec] CLI commands or use similar Fabric Manager/Device Manager procedure to collect more information if you suspect the module has been powered down because of errors. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-5-MOD_PWRUP: Module [dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 266
major temperature threshold. Recommended Action Enter the show env temperature CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-5-PS_CAPACITY_CHANGE: Power supply PS[dec] changed its - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 267
exceeded a major threshold. Recommended Action Enter the show env temperature CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PLATFORM-5-XBAR_DETECT: Xbar [dec] detected (Serial number [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 268
due to context-switch delay of [dec] msec. Explanation System will shut down in seconds because of a clock update failure. Recommended Action Enter the show env temperature CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 269
the show interface transceiver CLI command or use a similar Fabric Manager/Device Manager procedure to determine the transceiver being used. Contact your customer support representative for a list of authorized transceiver vendors. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 270
shutdown or use a similar Fabric Manager procedure to bring up the interface. Introduced Cisco MDS SAN-OS Release 1.2(2a). Cisco MDS SAN-OS Release 1.3(1). Error Message PORT-5-IF_DOWN_BUNDLE_MISCFG: Interface [chars] is down (Isolation due to channel mis-configuration on local or remote switch - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 271
. Recommended Action Bring the interface up by entering the no shutdown CLI command or by using a similar Fabric Manager procedure. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_CHANNEL_MEMBERSHIP_UPDATE_IN_PROGRESS: Interface [chars] is down (Channel membership update in - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 272
: Interface [chars] is down (dynamic vsan not present). Explanation The specified dynamic VSAN is not configured on this switch. Recommended Action Configure the dynamic VSAN. Introduced Cisco MDS SAN-OS Release 2.0(1b). 2-236 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 273
or use a similar Fabric Manager/Device Manager procedure to check the ELP failure reason field. Introduced Cisco MDS SAN-OS Release 1.2(2a payload size. Recommended Action Configure the attached switch port correctly and try again. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 274
) failed on the interface because loopback connection was detected. Recommended Action Connect to a port on another switch and try again. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_ELP_FAILURE_ISOLATION_LOOPBACK_DETECTED: Interface [chars] is down (Isolation due to ELP - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 275
Exchange switch parameter (ESC) failed on the interface. Recommended Action Enter the show port internal event-history CLI command or use a similar Fabric Manager/Device Manager procedure to determine the ESC protocol exchanges to determine how it failed. OL-15956-01 Cisco MDS 9000 Family - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 276
The Fibre Channel optical transceiver inserted is not a supported one. Recommended Action Contact your customer support representative for a list of authorized transceiver (SFP) vendors. Introduced Cisco MDS SAN-OS Release 1.2(2a). 2-240 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 277
has failed. Recommended Action Enter the show module internal all module command or use a similar Fabric Manager procedure to collect more information about the failed module. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_INACTIVE: Interface [chars] is down (Inactive - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 278
on this interface. Recommended Action Enter the show port internal info command or use a similar Fabric Manager procedure to determine the range of speed supported on this interface. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_INITIALIZING: Interface [chars] is down - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 279
Error Message PORT-5-IF_DOWN_INVALID_FABRIC_BINDING: Interface [chars] is down(Invalid fabric binding exchange). Explanation Fabric binding failed. Recommended Action Check the fabric binding database. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message PORT-5-IF_DOWN_LINK_FAILURE: Interface - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 280
use a similar Fabric Manager procedure to connect to the module to collect more information about the failed interface. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_LOOPBACK_ISOLATION: Interface [chars] is down (Isolation due to port loopback to same switch). Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 281
The physical link has gone down. Recommended Action Ensure that the cable is connected and the remote end is not shut down. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message PORT-5-IF_DOWN_NO_TRUNK_OPER_VSANS_ISOLATION: Interface [chars] is down(Isolation due to no common VSANs with peer on - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 282
. Recommended Action Enter the show interface command or use a similar Fabric Manager procedure to provide the peer IP address of this FCIP interface. Check to see why the peer closed the TCP connection. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_PEER_RESET: Interface - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 283
commands or use a similar Fabric Manager/Device Manager procedure to bring up the ports. Introduced Cisco MDS SAN-OS Release 1.2(2a). Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_SOFTWARE_FAILURE: Interface [chars] is down (Port software failure). Explanation The software servicing - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 284
. If this happens again, enter the show port internal all interface command or use a similar Fabric Manager procedure on the interface to gather more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_DOWN_SUSPENDED_BY_MODE: Interface [chars] is down (Suspended due to - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 285
is connected to the same remote switch as all the other interfaces in the PortChannel. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error CLI command or use a similar Fabric Manager/Device Manager procedure to check the connectivity to the peer. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 286
the host bus adapter (HBA) and enter the shutdown and no shutdown CLI commands or use a similar Fabric Manager/Device Manager procedure on the port. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message PORT-5-IF_DOWN_TOO_MANY_INTR: Interface [chars] is down (Error disabled - too many interrupts - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 287
vsan and show port internal event-history interface vsan CLI commands or use a similar Fabric Manager/Device Manager procedure to determine why this VSAN is down on this interface. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT-5-IF_TRUNK_UP: Interface [chars], VSAN [chars] is up - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 288
failed for module [dec]. Explanation Interfaces of the module may be in an indeterminate state. Recommended Action Reload the module. Introduced Cisco MDS SAN-OS Release 3.1(1). PORT-Resources Messages This section contains the port resources (PORT-RESOURCES) messages. Error Message PORT-RESOURCES - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 289
message. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(1). Deprecated Cisco MDS SAN-OS Release 1.3(4a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 290
Explanation The exchange fabric membership data (EFMD) initialization failed. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 291
a corrupted exchange fabric membership data (EFMD) request packet. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 292
the persistent storage service (PSS) operation that caused the error. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 293
[[chars]]. Explanation Module configuration failed. Recommended Action The module is automatically reset. If the problem persists, contact your customer support representative. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT_CHANNEL-1-MALLOC_FAILED: cannot allocate memory (size [dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 294
Action Make sure the compatibility parameters are consistent while adding ports to a PortChannel, or use the force option. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT_CHANNEL-3-GENERAL_ERROR: [chars]. Explanation General error. Recommended Action No action is required. Introduced - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 295
Action Execute the show port-channel consistency CLI command or use a similar Fabric Manager/Device Manager procedure to check all module connectivity and consistency. Introduced Cisco MDS SAN-OS Release 1.2(2a). PORT_CHANNEL-4 Error Message PORT_CHANNEL-4-PORT_CFG_DELETED: [chars] removed from - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 296
to come online because port channel interface - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 297
PORT_CHANNEL-6-PORT_DOWN: [chars]: [chars] is down. Explanation Port went down in a PortChannel. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT_CHANNEL-6-PORT_UP: [chars]: [chars] is up. Explanation Port came up in a PortChannel. Recommended - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 298
: started in active mode. Explanation PortChannel manager started in active mode. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PORT_CHANNEL-7-START_DEFAULT: started with default configuration. Explanation PortChannel manager started with the - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 299
Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS prevent this. This violating device or switch will be logged out. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 300
Explanation The exchange fabric membership data (EFMD) initialization failed. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 301
the PSS service, its current version number, and the expected version. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 302
-6-INFO: [chars]. Explanation An event happened that affects the port security manager. The error message indicates the event. Introduced Cisco MDS SAN-OS Release 1.3(4a). PROC_MGR Messages This section contains the process manager (PROC_MGR) messages. PROC_MGR-SLOT#-2 Error Message PROC_MGR - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 303
([chars]) could not be installed errno=[dec]. Explanation Component not installed. Recommended Action Check whether the component exists. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PROC_MGR-SLOT#-2-PROC_MGR_COMP_TIMEOUT: ERROR: Component ([chars]) did not exit and time out occurred - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 304
]] in [dec] sec [dec] usec... Explanation Removed the kernel-loadable module (KLM) script. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PROC_MGR-SLOT#-2-PROC_MGR_STOP_PROC: Process [[chars]] exited in [dec] sec [dec] usec... Explanation Process - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 305
] [dec]: Failed to take utaker semaphore: [dec]. Explanation Utaker semaphore take failed. Recommended Action Restart the line card. Introduced Cisco MDS SAN-OS Release 1.2(2a). PROC_MGR-SLOT#-4 Error Message PROC_MGR-SLOT#-4-PROC_MGR_APP_NOT_RESP: ERROR: Process ([chars]) is not responding, it will - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 306
working pages. Explanation Service needs more working page buffers. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 307
: [chars]: cannot read meta page from [chars]: [chars]. Explanation The persistent storage service cannot read the meta page of a database. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PSS-1-PSS_STAT_ERROR: [chars]: cannot stat [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 308
use a similar Fabric Manager procedure as a last recourse to clear this problem. Introduced Cisco MDS SAN-OS Release 1.2(2a). PSS-2 Error Message PSS-2-PSS_INVALID_SIZE: [chars]: database [chars] ([chars]) has invalid size [dec] (block size [dec]). Explanation The persistent storage service found - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 309
layout: [chars] (params [dec]/[dec]/[dec] -] [dec]/[dec]/[dec]). Explanation The persistent storage service layout is being converted. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message PSS-5-PSS_SHRINK: [chars]: shrinking pss: [chars]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 310
on the console or in the system log. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message QOS-2-PSS_ERROR: [chars]: PSS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 311
name shown in the error message. The file size could grow beyond its maximum limit. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). QOS-3 Error Message QOS-3-ALLOCFAIL: Heap Memory allocation failed: [chars]. Explanation QoS manager is out of dynamic memory - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 312
QoS manager failed to get license. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message QOS-3-MTSERROR: [chars]. Explanation QoS manager encountered a messaging and transaction service (MTS) error. The error message specifies the context where the error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 313
from the node and sap shown in the error message.This information is for debugging only. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). QOS-4 QOS-6 Error Message QOS-4-LICEXP: [chars]. Explanation QoS manager license is going to expire. The error message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 314
an E port came up or went down for the interface shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message QOS-6-ENABLED_UP_MARKING: [chars]. Explanation The QoS manager has enabled marking of time-critical control traffic as - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 315
manager is up and ready to accept client requests The service was initialized in the mode shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release . Error Message QOS-6-SWITCHOVER: Switching Over to other Supervisor. Explanation The QoS manager has - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 316
is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). RADIUS Messages This section contains the Remote Authentication Dial-In User Service (RADIUS) messages. RADIUS-2 RADIUS-3 Error Message RADIUS-2-RADIUS_NO_AUTHEN_INFO: ASCII authentication not supported. Explanation ASCII authentication - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 317
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message RADIUS-6-RADIUS_MESSAGE: [chars]. Explanation RADIUS message. Recommended Action No action is required. - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 318
Message RDL-3-SYSLOG_ERR: : [chars]. Explanation The remote domain lookup (RDL) syslog errors. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message RDL-3-SYSLOG_EXIT: : [chars]. Explanation The remote domain lookup (RDL) exiting on errors. Recommended - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 319
Error Message RDL-3-SYSLOG_MTS_ERR: : [chars]. Explanation The remote domain lookup (RDL) messaging and transaction service (MTS) errors. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). RDL-6 Error Message RDL-6-SYSLOG_DEBUG_1: : [chars] [hex]. Explanation The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 320
Base (RIB) caused failures in other services. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). RIB-3 Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 321
contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message RIB-3-MISS_APPS: Missing response from service. Explanation Service not responding to the Routing Information Base (RIB). Recommended Action Enter the debug rib error command, or use a similar Fabric Manager - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 322
directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). RIB-4 Error Message RIB-4-CPU_HOG: Inactive or busy. Explanation Either the Routing Information Base (RIB) was not scheduled to run, or RIB was busy, and RIB did not service the message or - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 323
The Routing Information Base (RIB) does not support this operation. Recommended Action Enter the debug rib all command, or use a similar Fabric Manager procedure, then recreate the operation scenario to find out more details. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message RIB - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 324
failed: [chars]: [chars]. Explanation Registered Link Incident Record (RLIR) messaging and transaction service (MTS) operation failed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message RLIR-2-PSS_FAILED: RLIR PSS operation failed: [chars]: [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 325
1b). Error Message RM-6-STARTING: deamon started. Explanation The resource manager daemon successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). RM-SLOT# Messages This section contains the resource manager slot (RM-SLOT#) messages. OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 326
critical error response reloading ILC. Explanation The listed component had a critical error timeout. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message RM-SLOT#-2-RM_VICPP_RECREATE_ERROR: All the fast path resources are down VICPP connectivity lost - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 327
failed: [chars]: [chars]. Explanation The Registered State Change Notification (RSCN) messaging and transactional services (MTS) operation failed Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message RSCN-2-PSS_FAILED: RSCN PSS operation failed: [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 328
(RSCN) was rejected. The FC ID and reason code are shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). RSCN-4 RSCN-6 Error Message RSCN-4-SWRSCN_REJECT: SW-RSCN rejected: [chars]: fcid [chars], Reason code-[chars], Reason code expl - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 329
Explanation Messaging and Transaction Service (MTS) operation failure. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 330
input/output to the persistent storage service (PSS). Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). 2-294 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 331
removed from the system. Recommended Action Ensure that the user exists. Make sure the user is not remotely authenticated. Introduced Cisco MDS SAN-OS Release 2.0(1b). SCHEDULER-4 Error Message SCHEDULER-4-SCH_WARN: [chars]. Explanation Scheduler warning. Recommended Action No action is required - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 332
cpu and show system internal sysmgr service all commands or use a similar Fabric Manager/Device Manager procedure to collect further information. See WWN Manager system error codes for the reason. Introduced Cisco MDS SAN-OS Release 2.0(1b). 2-296 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 333
used. Enter the show process cpu and show system internal sysmgr service all commands or use a similar Fabric Manager/Device Manager procedure to collect more information. See the VSAN Manager system error codes for the reason. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message SCSI target - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 334
persistent storage service (PSS) reload runtime database failed because of the error listed. Recommended Action Enter the show flash command or use a similar Fabric Manager/Device Manager procedure to collect more information. See PSS system error codes for reason. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 335
storage service (PSS) store runtime entry key failed because of the error shown in the error message. Recommended Action Enter the show flash command or use a similar Fabric Manager/Device Manager procedure to collect more information. See PSS system error codes for the reason. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 336
FIPS Bypass self-test status : [chars]. Explanation Status of the FIPS self-test. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message SECURITYD-2-FIPS_CRNG_SELF_TEST_STATUS: FIPS CRNG self-test status : [chars]. Explanation Status of the FIPS self-test - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 337
log cannot be stored. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). SECURITYD-6 Error Message SECURITYD - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 338
-OS Release 1.2(2a). Error Message SECURITYD-6-FIPS_MODE_SET: FIPS mode is [chars] for service [chars]. Explanation FIPS mode is changed. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message SECURITYD-6-FIPS_MODE_SET_FAILED: Error when setting FIPS mode - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 339
queuing to pending queue: [dec], Error code = [dec]. Explanation Sensor manager syslog message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Error Message SENSOR-3-SNSM_SYS_MTS_RECV_FAILURE: Sensor Mgr Error in receving MTS mesg: [dec], Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 340
Sensor Mgr Received bad MTS message: [dec]. Explanation Sensor manager syslog message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). SENSOR-5 Error Message SENSOR-3-SNSM_SYSLOG_MTS_PROCESS_ERROR: Sensor Mgr Error in processing MTS message: [dec], Error code - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 341
an informational message indicating that the Sensor Manager is shutting down. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message SENSOR_USD-2-SNSM_SYSYLOG_ALLOC_MEMORY: Sensor Mgr Memory allocation failed. Explanation This is an informational message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 342
]. Explanation This is an informational message indicating a receiving error from the messaging and transaction service (MTS). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message SENSOR_USD-3-SNSM_SYSLOG_BAD_MTS_MSG: Sensor Mgr Received bad MTS message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 343
encountered the listed error. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). SFM Messages This section - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 344
because another SME cluster (name , id %llx) already exists. Explanation A switch can be part of only one SME cluster. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.2(2). Error Message SME_CPP-3-LOG_ERR_SME_INTF_MISMATCH_CLUSTER_PARAMS: SME interface [chars] part - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 345
on a different switch or module. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release No action is required. Introduced Cisco MDS SAN-OS Release 3.2(2). Error Message SME_CPP-5-SME_DISABLED: SME Disabled. Explanation SME service is Disabled. Recommended Action No - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 346
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] Introduced Cisco MDS SAN-OS Release 3.2(2). Error Message SME_CPP-5-SME_ENABLED: SME Enabled. Explanation SME service is enabled. Recommended Action No action is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 347
Introduced Cisco MDS SAN-OS Release 3.0(1). SPAN Messages This section contains the switched port analyzer (SPAN) messages. SPAN-2 SPAN-3 Error Message SPAN-2-MEM_FULL: Memory allocation failed. Explanation Memory allocation failed. Recommended Action If you purchased Cisco support through a Cisco - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 348
Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(1). Error Message SPAN-3-SYSINFO_TIMEOUT: Span timed out waiting for response from port manager for sys info. Explanation The switched port analyzer (SPAN) request for critical - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 349
System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] SPAN-5 Error Message SPAN-5-ATL_VSAN_DEFAULT_ALL: Default to all VSANs for SPAN egress session. Explanation Generation 2 fabric switches support only one VSAN filter for an - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 350
or by using a similar Fabric Manager/Device Manager procedure. Introduced Cisco MDS SAN-OS Release 1.2(2a). switched port analyzer (SPAN) is starting stateless and the configuration will be reapplied to get back the active configuration. Recommended Action No action is required. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 351
: [chars]. Explanation Syslog message from a SAN Volume Controller (SVC) interface node. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). SVC-2 Error Message SVC-1-NODE_ALERT_MSG: [chars]. Explanation Syslog message from a SAN Volume Controller (SVC) interface - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 352
SVC interface. Then bring the SVC interface back up. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message SVC-2-SVC_SYSLOG_PATH_FAILURE: System Health detected SVC packet path failure for [chars]. Explanation The Caching Services Module (CSM) has been brought down by the System Health monitor - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 353
error continues, ask your customer support representative for assistance. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_BATT_FAILURE ) Battery Failed [chars]. Explanation The battery module on the Caching Services Module (CSM) has failed - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 354
1 with the latest level of code. 3. If the error continues, ask your support representative for assistance. It may be necessary to replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_INVALID_BATT_CAPACITY - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 355
fixed, manually mark the error as fixed. Introduced Cisco MDS SAN-OS support representative for assistance. 5. Mark the error you have just repaired as fixed. Introduced Cisco MDS problem persists, replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release 1.3(1). OL-15956-01 Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 356
Action Reload the node. If the problem persists, replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message 3. Ask your customer support representative for assistance. 4. Mark the error you have just repaired as fixed. Introduced Cisco MDS SAN-OS Release 1.3(1). - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 357
disk controller configuration. Recommended Action 1. Using service documentation for the disk controller, check that the correct configuration is set up for the disk controller. See also the IBM TotalStorage SAN Volume Controller for Cisco MDS 9000: Configuration Guide. 2. Mark the error you have - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 358
disk error recovery procedures have been performed by the disk controller. The problem is probably caused by a failure of some other component on the if no switch or disk controller failures were resolved in Steps 2 and 3. Call your customer support representative. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 359
on the same SAN as this cluster. 2. If problems are found, mark this error as fixed. 3. If no switch or disk controller failures can be found, take an error log dump and call your customer support representative. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-3-NODE_ERR_MSG: (SVC - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 360
to the service documentation for the disk enclosure or disk controller and the Fibre Channel network fabric to resolve the reported problem. 4. good status, contact the customer support representative to resolve the problem with the disk controller. Introduced Cisco MDS SAN-OS Release 1.3(1). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 361
or because of a Fibre Channel switch zoning problem. Recommended Action 1. Resolve any known Fibre Channel network problems. 2. Confirm that managed disks have the appropriate changes, ask your customer support representative for assistance. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 362
]. Explanation The svctask chpartnership or equivalent GUI or CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-3-NODE_ERR_MSG: (SVC [dec]/[dec] SS_ERR_CFG_SSH_KEY_ADDED ) Attempt to add SSH key (no effect) [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 363
, ask your customer support representative for assistance. It may be necessary to replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release If the problem persists, replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release 1.3(1). OL-15956-01 Cisco MDS 9000 Family - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 364
node is unable to see the FC fabric [chars]. Explanation No active or functioning logical Fibre Channel port was detected by the software. Recommended Action Reload the node. If the problem persists, replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 365
with the latest level of code. 3. If the error continues, ask your customer support representative for assistance. It may be necessary to replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-3-NODE_ERR_MSG: [chars]. Explanation Syslog message from a SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 366
problem determination on the error log to determine the cause of the pinned data and correct. Introduced Cisco MDS replace the Caching Services Module. Introduced Cisco MDS SAN-OS Release customer support representative for assistance. Introduced Cisco MDS SAN-OS Release 1.3(1). 2-330 Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 367
Recommended Action If there is a problem executing configuration commands, follow these cluster and should cause the switch to deactivate the IP address support representative for assistance, if the error continues. It may be necessary to replace the Caching Services Module. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 368
Action 1. Ensure that the software is at the latest level on the cluster. 2. Ask your customer support representative for assistance. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_INTERNAL_UNKNOWN_EXEC_MODE ) Internal error - run mode - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 369
Action 1. Ensure that the software is at the latest level on the cluster. 2. Ask your customer support representative for assistance. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_OPEN_MSG_QUEUE_FAILED ) Internal error - message queue - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 370
the cluster and if necessary repeat step 1 with the latest level of code. 3. Ask your customer support representative for assistance, if the error continues. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] Explanation The process cannot warm start - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 371
determine the problem on the remote node. If it is online, retry the command. Contact your customer support representative for assistance if it still fails. Cisco CLI commands or Fabric Manager procedures may be used to access the node directly as an alternative. Introduced Cisco MDS SAN-OS Release - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 372
the problem on the remote node. If it is online, retry the CLI command or use a similar Fabric Manager procedure. Contact your customer service representative for assistance if it still fails. Cisco CLI commands may be used to access the node directly as an alternative. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 373
the cluster. 3. Retry the software upgrade command. 4. If the installation fails again, report the problem to your customer support representative. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec]/[dec] SS_EID_PL_ER_PLIC_LINK ) Connection to a configured - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 374
been logged. Recommended Action Analyze the error log. Perform problem determination and correct any errors which have occurred. Migrate any specific extents which were not migrated because of the errors. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-4-NODE_WARNING_MSG: (SVC [dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 375
Action If there are device LUNs that should have been discovered by the node, follow these steps: 1. Perform a manual discovery. 2. Perform problem determination on the device. Introduced Cisco MDS SAN-OS Release 1.3(1). OL-15956-01 Cisco MDS 9000 Family System Messages Reference 2-339 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 376
Action Perform problem determination on the controller and network to determine the cause of the port error or exclusion. Introduced Cisco MDS SAN-OS created. Recommended Action Contact your customer support representative for assistance. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 377
: Interface [chars] is down. Explanation SAN Volume Controller (SVC) interface is down. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). SVC-6 Error Message SVC-5-SVC_SYSLOG_IF_UP: Interface [chars] is up. Explanation SAN Volume Controller (SVC) interface is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 378
. The node(s) then has to be removed and added back to the cluster. 3. Replace the Caching Services Module, if the error persists. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_EID_EC_ER_PWR_BUTTON ) Power withdrawn [chars]. Explanation Node - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 379
by the user, there is only one node left in the IO group. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_EID_IC_EV_SECURE_DELETE_COMPLETE ) Virtual Disk format completed [chars]. Explanation The formatting - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 380
view has been updated. [chars]. Explanation The node is in the process of discovering devices on the fabric. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_ADD_MAPPING ) Virtual Disk to Host SCSI - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 381
is retained for compatibility. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_CLUSTER_DISCOVERY ) Manual Managed Disk discovery invoked [chars]. Explanation The svctask detectmdisk IBM command has - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 382
[chars]. Explanation The svctask stopcluster IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_CREATE_FC_MAPPING ) Flash Copy mapping created [chars]. Explanation The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 383
[chars]. Explanation The svctask chcontroller IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_ERRORLOG_ANALYSE ) Error log analyzed [chars]. Explanation The svctask - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 384
dumped [chars]. Explanation The svctask dumperrlog IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_ERRORLOG_FIX ) Error log entry marked fixed [chars]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 385
[chars]. Explanation The svctask stopfcconsistgrp IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_HOST_DELETE ) Host deleted [chars]. Explanation The svctask rmhost - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 386
group [chars]. Explanation The svctask addmdisk IBM command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_MDISK_GRP_CREATE ) Managed Disk Group created [chars]. Explanation The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 387
Disk online [chars]. Explanation The managed disk that was excluded is now online. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_MIGRATE ) Virtual Disk migration to new Managed Disk group started - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 388
the pending state. It will shortly go into the online or offline state. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_NODE_REMOVE ) Node leaving cluster (expected) [chars]. Explanation The node has - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 389
dec] SS_ERR_CFG_NODE_UNPEND ) Node Unpend [chars]. Explanation The node has gone online. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_PLANAR_SN_CHANGE ) Attempt to change the Planar Serial Number - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 390
chars]. Explanation The svctask rmconsistgrp IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_REMOTE_DELETEREL ) Remote Copy relationship deleted [chars]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 391
has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_REMOTE_SWITCH ) Remote Copy relationship switched [chars]. Explanation The svctask switchrcrelationship IBM CLI command has been - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 392
and all nodes have been restored to the previous level of code. Recommended Action Perform problem determination on the cause of the upgrade failure and take corrective action before retrying the upgrade. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 393
[chars]. Explanation The svctask rmvdisk IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_VDISK_EXPAND ) Virtual Disk expanded [chars]. Explanation The svctask - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 394
[chars]. Explanation The svctask chvdisk -iogrp IBM CLI command has been invoked. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SVC-6-NODE_INFO_MSG: (SVC [dec]/[dec] SS_ERR_CFG_VDISK_SET_NAME ) Virtual Disk name modified [chars]. Explanation The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 395
Action Enter the show environment fan CLI command or use an equivalent Fabric Manager/Device Manager procedure to determine fan operation and take action to cool down the switch. Introduced Cisco MDS SAN-OS Release 1.3(4a). OL-15956-01 Cisco MDS 9000 Family System Messages Reference 2-359 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 396
Replace the battery. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(1). 2-360 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 397
. Recommended Action Replace the battery. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(4a). SVC_BATTERY-SLOT#-4 Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 398
that belong to a different class of services. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 399
the problem persists, use the init system CLI command from the switch(boot)# prompt to initialize the configuration partition. Note: This is a disruptive command. This command will initialize the switch, reset the entire internal disk, and reformat the bootflash: partition. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 400
problem persists, issue the init system CLI command from the switch(boot)# prompt to initialize the configuration partition. Note: This is a disruptive command. This command will initialize the switch, reset the entire internal disk, and reformat the bootflash: partition. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 401
for this service. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 Family - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 402
find the conversion library for this service. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 403
. Recommended Action If the problem persists, contact customer support. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(1). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 404
from service [chars]. Expected [dec]. Explanation A service cannot be started. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 405
reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-2-PARSEERR_DUP_UGRPENTRY: [chars]: service [chars] duplicated in the current upgrade group. Previous use - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 406
list of services. The initialization of the system cannot proceed further. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 407
list of services. The initialization of the system cannot proceed further. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 408
list of services. The initialization of the system cannot proceed further. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 409
you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-2-PARSEERR_INVALIDSTDBYDEPEND: [chars]: service [chars] cannot - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 410
If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-2-PARSEERR_REP_UGRPENTRY: [chars]: service [chars] is used - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 411
list of services. The initialization of the system cannot proceed further. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 412
for the fabric switch upgrade. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.1(1a). 2-376 Cisco MDS 9000 Family - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 413
not be saved for the fabric switch upgrade. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 3.1(1). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 414
the problem persists, Use the init system CLI command from the switch(boot)# prompt to initialize the configuration partition. Note:This is a disruptive command. This command will initialize the switch, reset the entire internal disk, and reformat the bootflash: partition. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 415
this message continues, contact your technical support representative. Introduced Cisco MDS SAN-OS Release 3.0(1). SYSMGR-3 Error CLI command or use a similar Fabric Manager/Device Manager procedure to find out what caused the switchover. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 416
process CLI command or use a similar Fabric Manager/Device Manager procedure to verify that the system is running properly and the service is behaving correctly. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-3-CFGWRITE_SRVTIMEOUT: Service [chars] failed to store its configuration - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 417
[chars] ([dec]). Explanation A service could not be started. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 418
that belong to a different class of services. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 419
The identity of a service is inconsistent in the image file. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 420
. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-3- service has failed to send a response after receiving a request for the fabric switch upgrade. Recommended Action If you purchased Cisco support through a Cisco - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 421
the value of the error code and the high availability policies implemented for the service, the service might be restarted automatically. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-3-SHUTDOWN_OVER: The System Manager is shutting down - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 422
A spawned service could not handshake with the system manager and was terminated. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 423
Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-4-PARSEWARN_RESTART_CNT_TOO_BIG: Service "[chars]": [chars] restart count of [dec] too big, needs to be set to [dec]. Explanation This is an internal debug message. Recommended Action If you purchased Cisco support through a Cisco reseller - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 424
a full upgrade. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-5-ALL_SCOPES_STARTED: System services have completely started at this time. Explanation System services have started. Recommended Action No action is required. Introduced - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 425
requested configuration erase has started. The error message shows the process ID of the process servicing the request. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-5-CFGINIT_STARTED: Initialization of the startup configuration started - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 426
reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message SYSMGR-5-HANDSHAKE_DONE: Handshake with service "[chars]" successfully performed. Explanation Handshake with the - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 427
Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(3). Error Message SYSMGR-5-ISSU_ABORT: Notifying services of aborted ISSU (PID - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 428
shows the process ID of the process servicing the request. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message fabric switch upgrade. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). 2-392 Cisco MDS 9000 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 429
to save the runtime database. This happens during the nondisruptive fabric switch upgrade. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.1(1a). Error Message SYSMGR-5-SERVICE_DELETED: Service [chars] has been removed from the System Manager database. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 430
This is not a problem or malfunction. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Deprecated Cisco MDS SAN-OS Release action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-6-SERVICE_STARTED: Service "[chars]" started with PID - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 431
"[chars]" failed in libvdb. Explanation The system could not find package information for this service in the version database. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-7-NO_STARTUP_CONFIG: No startup-config to convert. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 432
1.2(2a). Error Message SYSMGR-7-UNEXPECTEDMSG: Opcode [dec] not expected at this time from service "[chars]" ([chars]). Explanation Unexpected opcode. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message SYSMGR-7-UNKNOWNADDR: Opcode [dec] received from - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 433
an error on module [dec]. Reason: [chars]. Explanation Compact flash test errors. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.3(1a). Error Message SYSTEMHEALTH-2-OHMS_BOOTFLASH_FAILED_RESET_DAY: Bootflash hard resets for module [dec] has reached threshold limit in - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 434
Explanation Ethernet out-of-band channel (EOBC) test failed for the module. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SYSTEMHEALTH-2-OHMS_FIPS_FAILURE: FIPS compliance error during random number generation. Explanation FIPS compliance error - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 435
] Port [dec] has failed loop back tests. Explanation Port loop-back test failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SYSTEMHEALTH-2-OHMS_NVRAM_FAILED: Nvram test maximum failures reached for module [dec] for blocks 0x%llx. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 436
request due to errors found [chars] test. Explanation System Health switch reload request. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SYSTEMHEALTH-2-OHMS_SWITCHOVER_REQ: Supervisor switch over being requested due to errors found [chars] test - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 437
has been suspended due to internal errors. Explanation Battery test internal errors. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message SYSTEMHEALTH-4-OHMS_BATTERY_FAILING: Battery [dec] starting to fail on module [dec]. Reason: [chars]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 438
has been suspended due to internal errors. Explanation Cache disk test internal errors. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message SYSTEMHEALTH-4-OHMS_CF_CRC_PASSED: Compact Flash firmware on module [dec] is healthy at this time. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 439
fail on module [dec]. Explanation System Health cache disk failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Deprecated Cisco MDS SAN-OS Release 1.3(4b). Error Message SYSTEMHEALTH-4-OHMS_EMGMT_ERRORS: Management port test cannot proceed due to internal - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 440
[dec]. Explanation System Health Ethernet out-of-band channel failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Deprecated Cisco MDS SAN-OS Release 1.3(4b). Error Message SYSTEMHEALTH-4-OHMS_EXIT: Online System Health exiting due to internal errors - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 441
the inband test. Explanation Inband test has had too many errors while running. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message SYSTEMHEALTH-4-OHMS_LC_DAEMON_EXITED: System Health process running on module [dec] exited due to internal errors. Will - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 442
the Nvram test. Explanation NVRAM test has had too many errors while running. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message SYSTEMHEALTH-4-OHMS_SERDES_FAILED: Serdes loopback test on interface fc[dec]/[dec] failed. Explanation System Health - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 443
errors module cf-crc-check. If the condition persists, schedule a downtime and replace the compact flash on the affected module. Introduced Cisco MDS SAN-OS Release 3.1(3). Error Message SYSTEMHEALTH-4-OHMS_SUP_CF_RECALLED: Compact Flash on module [dec] is healthy at this time. But this has been - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 444
to errors. Explanation Online system health San Volume Controller (OHMS SVC) daemon exited. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message SYSTEMHEALTH-4-OHMS_TCAM_PARITY_ERRORS: TCAM test on module [dec] has been suspended due to internal errors - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 445
: Bootflash starting to fail on module [dec]. Explanation System Health bootflash failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4b). Error Message SYSTEMHEALTH-5-OHMS_CDISK_FAILING: Cache disk [dec] starting to fail on module [dec]. Explanation System - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 446
on module [dec]. Explanation System Health Ethernet out-of-band channel (EOBC) failing. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4b). Error Message SYSTEMHEALTH-5-OHMS_FREE_DISK_FAILING: Free Disk Space on partition [chars] is staring to go below threshold - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 447
for TCAM on module [dec] have been cleared. Explanation System Health TCAM failures cleared. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.3(1a). Error Message SYSTEMHEALTH-5-OHMS_TEST_FAILING: [chars] test starting to fail on module [dec]. Explanation System Health - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 448
bootflash on module [dec] have been cleared. Explanation System Health bootflash failures cleared. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message SYSTEMHEALTH-6-OHMS_CDISK_CLEARED: Failing conditions for cache disk [dec] on module [dec] have been - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 449
from module [dec] due to timeout errors. Explanation System Health inband timeout drop. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message SYSTEMHEALTH-6-OHMS_INBAND_TX_CONGESTION: Inband Unable to transmit due to TX path congestion on module [dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 450
. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.3(1). 2-414 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 451
Terminal Access Controller Access Control System Plus (TACACS+) error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.3(1). Error Message TACACS-6-TACACS_ACCOUNTING_MESSAGE: [chars]. Explanation Accounting message. Recommended Action No action is required - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 452
allocate memory. Recommended Action Enter the show tcap event-history CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message TCAP-2-PROC_DN: Process is shutting down: [chars]. Explanation Terminal - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 453
out of dynamic memory.The error message specifies the context where the failure occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message TLPORT-3-FC2ERROR: [chars]. Explanation TL port manager encountered a Fibre Channel Layer 2 (FC-2) error. The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 454
where the error occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). TLPORT-6 Error Message TLPORT-3-PSSERROR: [chars]. Explanation TL port manager encountered a persistent storage service (PSS) error. The error message specifies the context where the - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 455
message shows the Interface-ID string that identifies the TL port. This is an informational message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). TP C Messages TPC stands for Third Party Copy. It is for the feature Network Accelerated Serverless Backup (NASB - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 456
Error Message TTYD-2-TTYD_MTS: TTYD Message queue [dec] [chars]. Explanation Miscellaneous TTY daemon (TTYD) message problem. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message TTYD-2-TTYD_SDWRAP: TTYD Debug Facility error [dec] [chars]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 457
-6 Error Message TTYD-3-TTYD_MISC_ERROR: Error [chars] with error [chars]([hex]). Explanation Miscellaneous TTY daemon (TTYD) problems. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message TTYD-6-TTYD_MISC: TTYD [chars]. Explanation The TTY daemon - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 458
at http://www.t10.org Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 1.3(4b). VEC-SLOT#-4 Error Message VEC-SLOT#-3-LOG_GUID_MISMATCH: GUID Mismatch DPP [dec] PWWN [chars] lun [chars] Expected [chars] Read [chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 459
]. Explanation An event is received for a state in the virtual enclosure client (VEC) GUID ID finite state machine (FSM) that should not have occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message VEC-SLOT#-5-LOG_ERR_VEC_HOST: Host VSAN :[dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 460
enclosure client (VEC) HOST XP finite state machine (FSM) that should not have occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VEC-SLOT#-5-LOG_ERR_VEC_NPORT_FSM: Illegal Event [chars] in State [chars] FSM [chars]. Explanation An event is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 461
) could not be created as the intelligent line card (ILC) limit of VEPs has been reached. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VEC-SLOT#-5-LOG_ERR_VEC_VLUN_FSM: Illegal Event [chars] in State [chars] FSM [chars]. Explanation An event is - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 462
client (VEC) VSAN XCHG finite state machine (FSM) that should not have occurred. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VEC-SLOT#-5-LOG_NOTICE_VEC_SLEEP_THRESH: VEC not scheduled for [dec] seconds. Explanation The virtual enclosure client - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 463
could not allocate memory. Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). VEDB_MGR-6 Error Message VEDB_MGR - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 464
virtualized by the control plane processor (CPP). Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(2b). Error Message VES-SLOT#-5-LOG_ERR_VES_PATH_FSM: disk guids dont match - received verify_mismatch for pid [dec] from vec [dec]. Explanation A VERIFY MISMATCH event - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 465
the virtual Fibre Channel (VFC) messages. VFC-3 Error Message VFC-3-VFC_MEM_ERROR: Memory consistency problem. Explanation Miscellaneous target error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message VFC-3-VFC_TGT_ERROR: Target error:[chars] 0x%llx - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 466
performed. Recommended Action Enter the show SCSI target internal driver CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VHBAD-2-PROC_SET_SCSI_INDEX_FAIL: Failed to set SCSI index SCSI target - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 467
the show process cpu and show system internal sysmgr service all CLI commands or use a similar Fabric Manager/Device Manager procedure to collect more information. See the VSAN Manager system error codes for reason. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VHBAD-3-PSS_CREATE_FAIL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 468
storage service (PSS) reload runtime database failed because of the error shown in the error message. Recommended Action Enter the show flash CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. See PSS system error codes for reason. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 469
service (PSS) snapshot of runtime to URI failed because of the error shown in the error message. Recommended Action Enter the show flash CLI command or use a similar Fabric Manager/Device Manager procedure to collect more information. See PSS system error codes for the reason. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 470
switch. Introduced Cisco MDS SAN-OS Release 1.2(2a). VNI-6 Error Message VNI-3-INIT_FAILED: Initialization failed. Component [chars]. Explanation The service Fabric Manager/Device Manager procedure to check the status of the other processes. Debug the specified component. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 471
Recommended Action If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 472
port manager (VPMON) daemon experienced a critical problem. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message switch application programming interface (ISAPI) users need to re-download the configuration data to the fast path. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 473
purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VPM-3-UNKNOWN_MSG: Recvd. from Node=[dec] SAP=[dec]. Explanation The virtual port manager has received an unknown message from the node and service access point - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 474
manager on the standby supervisor became active and it is ready to serve client requests. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VPM-6-BECAME_STDBY: Became STANDBY from active mode. Explanation The virtual port manager became standby from - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 475
is up and ready to accept client requests. The service was initialized in the mode shown in the error message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VPM-6-SWITCHOVER: Switching Over to other Sup. Explanation The virtual port manager - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 476
Message VPM-6-VPMON_INFO: [chars]. Explanation A virtual port manager informational message. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message VPM-6-VPMON_STARTING: deamon started. Explanation The virtual port manager daemon successfully started - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 477
Action Check the system memory. If memory is low, reset the switch. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VRRP_CFG-3-INIT_FAILED: Initialization failed. Component [chars]. Explanation The service failed to start. The failure occurred while initializing the component shown in - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 478
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] VRRP_CFG-5 Error Message VRRP_CFG-5-STARTING: VRRP Manager service started. Explanation The service successfully started. Recommended Action No action is required. - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 479
: Memory allocation failed. Explanation The service failed to allocate a block of dynamic memory. Recommended Action Check if the system is low on memory and reset the switch if necessary. Introduced Cisco MDS SAN-OS Release 1.2(2a). OL-15956-01 Cisco MDS 9000 Family System Messages Reference - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 480
Cisco MDS SAN-OS Release 1.2(2a). VRRP_ENG-4 Error Message VRRP_ENG-3-INIT_FAILED: Initialization failed. Component [chars]. Explanation The service similar Fabric Manager/Device Manager procedure to check the status of the other processes and debug the specified component. Introduced Cisco MDS SAN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 481
Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message VRRP_ENG-5-STARTING: VRRP Engine service started. Explanation The service successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). VRRP_ENG-6 Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 482
. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VRRP_ENG-6-STARTING: VRRP Engine service started. Explanation The service successfully started. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 483
Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message VSAN-3-CFS_OPERATION_FAILED: cfs [chars] operation failed : [chars]. Explanation The Cisco Fabric Services (CFS) operation has failed. Recommended Action Check the reason for the failure of the CFS operation and rectify the problem - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 484
Message VSAN-6-CFS_MERGE_NOT_SUPPORTED: merging of fctimer configuration data is not supported. Explanation Merging of fctimer configuration data using CFS is not supported. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message VSAN-6-CREATED: Created - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 485
: Source URI:[chars] Destination URI:[chars] errcode:[dec]. Explanation Persistent storage service (PSS) snapshot error. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). VSHD-3 Error Message VSHD-2-VSHD_SYSLOG_SDWRAP_ERR: Description:[chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 486
Persistent storage service (PSS) handling error. Introduced Cisco MDS SAN-OS switches in the fabric. Recommended Action Edit the configuration on one of the switches to obtain the desired role configuration database and then commit it. Introduced Cisco MDS SAN-OS Release 2.0(1b). 2-450 Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 487
This is probably occurring due to different versions of system image on switches in the fabric. Recommended Action Make sure all switches are running the same version of the system image. Introduced Cisco MDS SAN-OS Release 2.0(1b). VSHD-5 Error Message VSHD-4-VSHD_ROLE_DISTRIBUTE_FAILURE: Role - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 488
on the console or in the system log. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message WWN-2-EXITING: Exited due to - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 489
console or in the system log. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message WWN-2-PSS_BKP_PSS_MISMATCH: Block - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 490
a new secondary MAC address and its range. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message WWN-3-PSS_SYNC_TO_STNDBY_FAILED: PSS TYPE=[chars] KEY=[chars]. Explanation Could not send persistent storage service (PSS) synchronization notification to the standby supervisor module. PSS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 491
than the maximum number of WWNs that can be allocated or released in a single request. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message WWN-3-UNKNOWN_MSG: Received from Node=[dec] SAP=[dec] Opcode=[dec]. Explanation The WWN manager has received - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 492
its persistent storage databases. The persistent information has been translated to the new format. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message WWN-4-TYPE1_WARN: [dec] (< [dec] %) Remain. Explanation The WWN manager has only the shown percent - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 493
standby supervisor module became active and it is ready to serve client requests for WWNs. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message WWN-6-BECAME_STDBY: Became STANDBY from active mode. Explanation The WWN manager became standby from active - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 494
Cisco MDS SAN-OS Release 1.2(2a). Error Message WWN-6-SERVICE_UP: Initialized [chars]. Explanation The WWN manager is up and ready to accept client requests for WWNs. The service switched over to the standby supervisor module. Recommended Action No action is required. Introduced Cisco MDS - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 495
return_code [hex] ([chars]). Explanation The supervisor has experienced an arbiter setup failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message XBAR-5-ARB_INIT_PORT_FAIL: Arbiter reported failure to register port [dec] in group [dec] return_code - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 496
the show xbar internal event-history command or use a similar Fabric Manager/Device manager procedure to collect more informations about the crossbar component. Power cycling the module may fix the problem. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message XBAR-5-XBAR_INIT_FAIL: Xbar [[dec - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 497
] return_code [hex] ([chars]). Explanation The supervisor has experienced an xbar setup failure. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 3.0(1). Error Message XBAR-5-XBAR_PORT_ENABLE_FAIL: Xbar [[dec].[dec]] reported failure to enable port [dec] return_code [hex - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 498
[dec] [chars] received from the API call. Recommended Action Perform a manual build fabric using fcdomain's interface if you would like to remove the unused virtual domain(s) from the fcdomain list. Introduced Cisco MDS SAN-OS Release 3.0(1). XBAR_CLIENT Messages This section contains the crossbar - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 499
Enter the show xbar-client event-history command or use a similar Fabric Manager/Device manager procedure to collect more information. Introduced Cisco MDS SAN-OS Release 1.2(2a). Deprecated Cisco MDS SAN-OS Release 3.0(1). Error Message XBAR_CLIENT-2-PROC_INITFAIL: Process initialization failed due - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 500
in the system log. If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased support directly from Cisco Systems, contact Cisco Technical Support. Introduced Cisco MDS SAN-OS Release 1.2(2a). 2-464 Cisco MDS 9000 Family System Messages Reference OL - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 501
The zone server cannot acquire change authorization. Recommended Action Verify the interoperability mode on all the switches or retry later. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-2-ZS_CHANGE_ACQUIRE_AUTH_FAILED: Acquire authorization failed on VSAN [dec]. Explanation The - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 502
server cannot activate because of reason shown in the error message on the domain. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-2-ZS_CHANGE_APPLY_FAILED: Apply changed failed on VSAN [dec]. Explanation The zone server cannot apply changes - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 503
Explanation The zone server cannot stage the zone configuration. Recommended Action Verify the interoperability mode on all the switches. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-2-ZS_CHANGE_SFC_REJECTED: SFC received from remote domain [dec] is rejected. Explanation Received - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 504
]. Explanation The zone server cannot stage distribute zone set database on the VSAN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message ZONE-2-ZS_CHANGE_STAGE_SET_ZONING_MODE_FAILED: Stage set zoning mode failed on VSAN [dec]. Explanation The zone - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 505
and read-only attribute and reactivating active zone sets on all affected VSANs. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-2-ZS_LIC_FAILURE: License [chars] operation failed for license [chars]. Explanation License operation failed - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 506
. Recommended Action Compare the active zone set with the adjacent switch by entering the zone merge interface CLI command or by using a similar Fabric Manager/Device Manager procedure. Introduced Cisco MDS SAN-OS Release 1.2(2a). 2-470 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 507
interoperability mode to the same value on both switches. Introduced Cisco MDS SAN-OS Release 2.0(1b). Error Message ZONE-2-ZS_MTS_OPER_FAILED: MTS [chars] operation failed : [chars]. Explanation The zone server messaging and transaction service (MTS) operation failed. Recommended Action No action - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 508
[chars], got [chars]). Explanation Configuration version mismatch. persistent storage service (PSS) URL expected the shown version, but the stored version is different. Recommended Action Upgrade or downgrade to the expected version. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 509
2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] Error Message ZONE-2-ZS_TCAM_SWITCHED_TO_SOFT_ZONING_MODE: Switched to soft zoning : Reason: Hard zoning disabled. Explanation Switched to soft zoning. Hard zoning was - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 510
failed because QoS was not enabled. Recommended Action Make sure QoS is enabled and reactivate the zone set in the VSAN. Introduced Cisco MDS SAN-OS Release 2.0(1b). ZONE-4 Error Message ZONE-4-LZ_OTHER_CMD_TO_ZONED_OUT_LUN: FCP command [hex] received from SID=[chars] to DID=[chars] for LUN=[chars - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 511
. The line card upgrade will occur after the completion of the change protocol. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-4-ZS_LICENSE_EXPIRY_WARNING: Feature [chars] evaluation license [chars] expiry in [dec] days. Explanation Feature - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 512
mode to the appropriate value, or make sure that the active or full zone set has only supported members in the current interoperability mode. Introduced Cisco MDS SAN-OS Release 1.3(4a). Error Message ZONE-5-ZS_EXPORT_IMPORT_COMPLETE: [chars] operation completed. Explanation The export or import - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 513
mode. Explanation The LUN read-only zoning process on the standby supervisor became active. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-6-LZ_BECAME_STDBY: LUN/Read-only Zoning Process became STANDBY from active mode. Explanation The LUN - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 514
has received a request sense fcp command from source ID to destination ID for the LUN. Recommended Action No action is required. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-6-LZ_SERVICE_UP: LUN/Read-only Zoning Process initialized [chars]. Explanation The LUN read-only zoning - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 515
the domain list does not match or authorization has already been acquired by another switch. Recommended Action Verify the interoperability mode on the switch. Introduced Cisco MDS SAN-OS Release 1.2(2a). Error Message ZONE-6-ZS_FC2_OPER_INFO: FC2 [chars] operation failed : [chars]. Explanation - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 516
Chapter 2 System Messages and Recovery Procedures for the Cisco MDS 9000 Family Send documentation comments to [email protected] 2-480 Cisco MDS 9000 Family System Messages Reference OL-15956-01 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 517
Send documentation comments to [email protected] A A P P E N D I X OHMS_BOOTFLASH_ERRORS Revised: November, 2007 OL-15956-01 DISK FAILURE ) failed. OD_DISK_IOCTL_GET_STATE2_FAILED Ioctl(CHECKPOWERMODE2) failed. OL-15956-01 Cisco MDS 9000 Family System Messages Reference A-1 - HP Cisco MDS 9216A | Cisco MDS 9000 Family System Messages Reference (OL-15956-0 - Page 518
Appendix A OHMS_BOOTFLASH_ERRORS Send documentation comments to [email protected] Table A-1 OHMS_BOOTFLASH_ERRORS Description (continued) Reason Code . OD_DISK_NOR_REFLASH_FAILED Disk firmware update procedures failed. Cisco MDS 9000 Family System Messages Reference A-2 OL-15956-01
Send documentation comments to [email protected]
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Cisco MDS 9000 Family System Messages
Reference
Cisco MDS 9000 SAN-OS Release 3.3(1a)
April 2008
Text Part Number: 0L-15956-01