HP DL320 HP ProLiant DL320 Generation 2 Server Maintenance and Service Guide - Page 42

Power Supply, Removing the power supply

Get HP DL320 - ProLiant - G3 PDF manuals and user guides
UPC - 829160513218
View all HP DL320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Removal and Replacement Procedures Power Supply IMPORTANT: A "Fan 5 Error" indicates an error from one of the fans located in the power supply. When this error occurs, replace the entire power supply unit. To remove the power supply: 1. Power down the server. See "Powering Down the Server" in this chapter. 2. Remove the access panel. See "Server Access Panel" in this chapter. 3. Remove the PCI riser board assembly. See "PCI Riser Board Assembly" in this chapter. 4. Remove the center wall. See "Center Wall" in this chapter. 5. Disconnect the hard drive power cables from the hard drives (1). 6. Disconnect the power supply cable from the power supply connector on the system board by pressing the locking tab on the side of the connector and pulling upwards (2). 7. Remove the two Phillips-head screws that secure the power supply unit to the chassis (3). 8. Slide the power supply away from the back of the chassis and lift it from the server (4). Figure 2-26: Removing the power supply Reverse steps 1 through 8 to replace the power supply. HP ProLiant DL320 Generation 2 Server Maintenance and Service Guide 2-31 HP CONFIDENTIAL Codename: Moonstar 306 Part Number: 293164-004 Last Saved On: 9/22/03 1:47 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Removal and Replacement Procedures
Power Supply
IMPORTANT:
A “Fan 5 Error” indicates an error from one of the fans located in the power supply.
When this error occurs, replace the entire power supply unit.
To remove the power supply:
1.
Power down the server. See “Powering Down the Server” in this chapter.
2.
Remove the access panel. See “Server Access Panel” in this chapter.
3.
Remove the PCI riser board assembly. See “PCI Riser Board Assembly” in this chapter.
4.
Remove the center wall. See “Center Wall” in this chapter.
5.
Disconnect the hard drive power cables from the hard drives (1).
6.
Disconnect the power supply cable from the power supply connector on the system board
by pressing the locking tab on the side of the connector and pulling upwards (2).
7.
Remove the two Phillips-head screws that secure the power supply unit to the chassis (3).
8.
Slide the power supply away from the back of the chassis and lift it from the server (4).
Figure 2-26: Removing the power supply
Reverse steps 1 through 8 to replace the power supply.
HP ProLiant DL320 Generation 2 Server Maintenance and Service Guide
2-31
HP CONFIDENTIAL
Codename: Moonstar 306 Part Number: 293164-004 Last Saved On: 9/22/03 1:47 PM