HP DreamColor Z32x User Guide - Page 23

Removing the monitor stand, Mounting the monitor

Get HP DreamColor Z32x PDF manuals and user guides View all HP DreamColor Z32x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Removing the monitor stand You can remove the monitor panel from the stand to install the panel on a wall, a swing arm, or other mounting fixture. CAUTION: Before beginning to disassemble the monitor, be sure the monitor is turned off and all cables are disconnected. 1. Disconnect and remove all cables from the monitor. 2. Lay the monitor face down on a flat surface covered by a clean, dry cloth. 3. Press up on the latch near the bottom center of the monitor to unlock the HP Quick Release 2 (1). 4. Swing the bottom of the stand up until the mounting plate clears the recess in the panel (2). 5. Slide the stand out of the recess (3). Mounting the monitor The monitor panel can be attached to a wall, swing arm, or other mounting fixture. NOTE: This apparatus is intended to be supported by UL or CSA Listed wall mount bracket. CAUTION: This monitor supports the VESA industry standard 100 mm mounting holes. To attach a thirdparty mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long screws are required. Longer screws must not be used because they may damage the monitor. It is important to verify that the manufacturer's mounting solution is compliant with the VESA standard and is rated to support the weight of the monitor display panel. For best performance, it is important to use the power and video cables provided with the monitor. 1. Remove the monitor from the stand (see Removing the monitor stand on page 17). Removing the monitor stand 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
Removing the monitor stand
You can remove the monitor panel from the stand to install the panel on a wall, a swing arm, or other
mounting fixture.
CAUTION:
Before beginning to disassemble the monitor, be sure the monitor is turned off and all cables are
disconnected.
1.
Disconnect and remove all cables from the monitor.
2.
Lay the monitor face down on a flat surface covered by a clean, dry cloth.
3.
Press up on the latch near the bottom center of the monitor to unlock the HP Quick Release 2 (1).
4.
Swing the bottom of the stand up until the mounting plate clears the recess in the panel (2).
5.
Slide the stand out of the recess (3).
Mounting the monitor
The monitor panel can be attached to a wall, swing arm, or other mounting fixture.
NOTE:
This apparatus is intended to be supported by UL or CSA Listed wall mount bracket.
CAUTION:
This monitor supports the VESA industry standard 100 mm mounting holes. To attach a third-
party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm long screws are required. Longer
screws must not be used because they may damage the monitor. It is important to verify that the
manufacturer’s mounting solution is compliant with the VESA standard and is rated to support the weight of
the monitor display panel. For best performance, it is important to use the power and video cables provided
with the monitor.
1.
Remove the monitor from the stand (see
Removing the monitor stand
on page
17
).
Removing the monitor stand
17