Home > HP Manuals > Desktops > HP ENVY 700-074 > Manual Viewer

HP ENVY 700-074 Upgrading and Servicing Guide

HP ENVY 700-074 Manual

HP ENVY 700-074 manual table of contents:

  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 1
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 2
    Copyright © 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Part Number: 655130-001 Version: 1.0
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 3
    Upgrading and Servicing Guide HP Elite 7300 MT HP Pavilion HPE h8-1000 Series PC Computer features may vary by model. Removing and Replacing a Hard Disk Drive on page 2 Removing and Replacing a CD/DVD Drive on page 9 Upgrading or Replacing Memory on page 14 Upgrading or ...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 4
    ... can damage the electronic components inside the computer. Discharge static electricity by touching the metal ...loosen the screw on the back panel that secures the panel to the computer. Small screws are easily lost. Remove ... if they fall. 2 Upgrading and Servicing Guide Features may vary by model....
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 5
    ...Slide the side panel toward the back of the computer, and then pull the side panel.... 7. Open the front bezel, and then remove it from the computer. The inside of the computer is exposed. 8. 9. Lay the computer on a flat surface. Remove the two screws holding the retaining bar in place. 6. Lift...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 6
    .... 11. Remove the three screws that attach the hard disk drive cage to the computer. 13. Grasp the hard drive cage and slide the cage toward the ...: Some models may have only two screws attaching the hard disk drive cage to the computer. 4 Upgrading and Servicing Guide Features may vary by model.
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 7
    14. Disconnect the two cables from the end of the hard disk drive. The cables may have a latch that is pressed to release the cable. NOTE: Keep the four screws available as they will be used in the new hard drive. Installing a new hard disk drive NOTE: The replacement part may look different than...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 8
    ...the slots (1), press down and slide the cage toward the bottom of the computer until it stops (2), ensuring that the three screw holes are aligned. 4..... 6. Using a flathead or Torx screwdriver, secure the hard disk drive cage in place. 6 Upgrading and Servicing Guide Features may vary by model.
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 9
    ... and then align the screw holes at the front of the computer (2). 10. Insert the three tabs on the bezel ... place. 11. Install the side panel on the side of the computer, and then slide it toward the front ...position. NOTE: Make sure the panel is flush with the computer. Failure to do so might cause ...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 10
    ... recovery discs. To install the operating system, refer to the instructions included with your system recovery discs, or available from the HP support site (www.hp.com/... and restore any data you backed up. 8 Upgrading and Servicing Guide Features may vary by model.
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 11
    ... shut down your operating system. Unplug the computer by disconnecting the power cord and all ... applied. You might damage your computer or be injured by the spinning the fan blades. WARNING! ... can damage the electronic components inside the computer. Discharge static electricity by touching the metal ...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 12
    5. Slide the side panel toward the back of the computer, and then pull the side panel away ... front bezel, and then remove it from the computer. The inside of the computer is exposed. 8. To unlock the CD/DVD ..."Lever A", move "Lever B." 10 Upgrading and Servicing Guide Features may vary by model.
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 13
    ... of the original part. 1. Locate where the CD/DVD drive is to be inserted. 10. Push the CD/DVD drive from behind. 2. Insert the new CD/DVD drive into the slot. 11. Pull the CD/DVD drive out the front of the computer. Features may vary by model. Removing and Replacing a CD/DVD Drive 11
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 14
    .... 6. Reattach the front bezel by inserting the three tabs into the slots on the computer, and then close the bezel door until it locks in place.... drive to install, repeat this step. However, instead of moving "Lever A", move "Lever B." 12 Upgrading and Servicing Guide Features may vary by model.
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 15
    ... computer, and then slide it toward the front of the computer. 9. Plug the power cord and any ... computer. NOTE: Make sure the panel is flush with the computer. Failure to do so might cause ... Tighten the screw, securing the side panel to the back of the computer. 10. Press the power button to turn ...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 16
    ... can damage the electronic components inside the computer. Discharge static electricity by touching the metal ... Compatibility Verify that the memory installed is compatible with this computer. SO-DIMMs are small outline dual ... thinner than 14 Upgrading and Servicing Guide Features may vary by model...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 17
    ...7. Lay the computer on a flat surface. Locate the memory inside the computer. 5. Slide the side panel toward the back of the computer... the memory card by the edges, gently remove it from the compartment (2). The inside of the computer is exposed. 9. To remove additional memory cards, repeat step ...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 18
    ... snaps in place. 3. 4. If you are replacing more than one memory card, repeat step 2 for each memory card. Place the computer in an upright position. 16 Upgrading and Servicing Guide Features may vary by model.
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 19
    ...any additional cables into the back of the computer. Troubleshooting If the computer displays a memory error after you have turned it back on: 1. 2. 3. Turn the computer off and unplug the power cord... place. 8. Press the power button to turn on the computer. Features may vary by model. Upgrading...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 20
    ... power applied. You might damage your computer or be injured by the spinning the fan blades. WARNING! ...electricity can damage the electronic components inside the computer. Discharge static electricity by touching the metal ...if they fall. 18 Upgrading and Servicing Guide Features may vary by model....
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 21
    5. Slide the side panel toward the back of the computer, and then pull the side panel ... the screw holding the bracket in place. 6. 7. Lay the computer on a flat surface. Remove the two screws .... 10. Remove the screw that secures the bracket to the computer. Features may vary by model. Upgrading ...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 22
    11. Remove the bracket from the back of the computer. 13. If the add-in card is in the large slot, press the latch to release the card. 12. ... them. 15. If there are additional add-in cards to be removed, repeat step 14 for each card. 20 Upgrading and Servicing Guide Features may vary by model.
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 23
    ... or model differences; however, the replacement part meets or exceeds the specifications of the original part. 1. Locate where the card will be seated inside the computer. Insert the add-in card into the slot on the motherboard, making sure it is firmly seated in place. 3. If the auxiliary power ...
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 24
    ...add-in card in place, replace the bracket at the back of the computer. 7. Insert the two screws, securing the retaining ... then align the screw holes at the front of the computer (2). NOTE: Make sure the panel is flush ... close securely. 22 Upgrading and Servicing Guide Features may vary by model....
  • HP ENVY 700-074 | Upgrading and Servicing Guide - Page 25
    10. Tighten the screw, securing the side panel to the back of the computer. 11. Plug the power cord and any additional cables into the back of the computer. 12. Press the power button to turn on the computer. Features may vary by model. Upgrading or Replacing an Add-in Card 23



Type your new search above
We apologize, but we cannot currently deliver this PDF manual.
You can visit the HP ENVY 700-074 on the HP site to download this or other manuals by visiting this link.

We apologize for any inconveniece.

The manual viewer requires the flash plugin to be installed and enabled.
To view this page ensure that Adobe Flash Player version 10 or greater is installed.

HP ENVY 700-074 Manual