HP ProLiant DL160 HP ProLiant DL160 Generation 5 Server Maintenance and Servic - Page 77

Device number, Connector, To remove the system fan

Get HP ProLiant DL160 - G5 Server PDF manuals and user guides View all HP ProLiant DL160 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Device number System fan 5 System fan 6 Connector P18 on the system board P24 on the system board System fans 1 to 5 are for the memory modules and processors, while system fan 6 is for the PCI slots and system chipsets. A new system fan can be installed to allow the server to operate properly in case a default system fan becomes defective. To remove the system fan: 1. Disconnect the fan cable from its corresponding board connector. 2. Release the fan cable from the cable clip. 3. Lift the system fan away from the chassis. Figure 69 Removing the system fan To replace the system fan: 1. Put the fan cable through the system fan bracket. Secure the cable with the cable clip on the chassis. 2. Hold the system fan and press the system fan into the fan bracket. 3. Connect the fan cable to its corresponding board connector. Removal and replacement procedures 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Removal and replacement procedures
77
Device number
Connector
System fan 5
P18 on the system board
System fan 6
P24 on the system board
System fans 1 to 5 are for the memory modules and processors, while system fan 6 is for the PCI slots and
system chipsets.
A new system fan can be installed to allow the server to operate properly in case a default system fan
becomes defective.
To remove the system fan:
1.
Disconnect the fan cable from its corresponding board connector.
2.
Release the fan cable from the cable clip.
3.
Lift the system fan away from the chassis.
Figure 69
Removing the system fan
To replace the system fan:
1.
Put the fan cable through the system fan bracket. Secure the cable with the cable clip on the
chassis.
2.
Hold the system fan and press the system fan into the fan bracket.
3.
Connect the fan cable to its corresponding board connector.