HP Scitex FB7600 Essential Health and Safety Instructions Rev.C - Page 14

Fire Hazards

Get HP Scitex FB7600 PDF manuals and user guides View all HP Scitex FB7600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

• It is the customer's responsibility to ensure that electrical works comply with the local electrical code and the relevant laws and regulations. The customer should provide qualified and registered electricians to perform operations as required by these laws and regulations. • In general, HP service personnel are authorized to perform maintenance operations in all printer's parts and subassemblies, but not for the site electrical infrastructure and printer's connections to this structure. Safe isolation of the printer from power prior to service operations shall be done according to local regulations, and is under the customer's responsibility. • When servicing any electrical components, especially the vacuum pump cabinet or loader cabinet, turn off the main power switch and padlock it (see Figure 1-2 on page 5). Danger Only a certified electrician is authorized to carry out any electrical work. Fuses blown within 36 hours of being replaced may indicate malfunctioning electrical circuits within the system. Have qualified service personnel check the system, and do not attempt to replace the fuse again! Danger An electrical hazard may exist if any light, monitor, or visual indicator stays ON. To prevent possible injury, immediately turn OFF the switch in the mains power supply box on the wall. Fire Hazards UV-based inks used with the HP Scitex FB7600 have flammable and irritant properties. Their combustion products include oxides of carbon. Danger Extreme care must be taken when handling inks and solvent to prevent the risk of fire. Do not permit smoking or naked flames in the print production or storage areas and ensure that warning signs (see Figure 1-3 below) are prominently displayed in appropriate positions. 0 DANGER: EXPLOSIVE VAPOR, NO SMOKING, NO OPEN FLAMES, NO SPARKS Figure 1-3 Warning Signs Always keep two 6 kg fire extinguishers near each HP Scitex FB7600. Never use water to extinguish a fire! In the event of a fire, switch the electricity OFF before extinguishing the fire. Use a carbon dioxide fire extinguisher only. Danger Conductive fluids that seep into the active circuit components of the system may cause short circuits, which can result in electrical fires. Therefore, do not place any liquid or food on any part of the system. 6 HP Scitex Industrial Presses Essential Health and Safety Instructions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
6
HP Scitex Industrial Presses Essential Health and Safety Instructions
•
It is the customer’s responsibility to ensure that electrical works comply
with the local electrical code and the relevant laws and regulations. The
customer should provide qualified and registered electricians to perform
operations as required by these laws and regulations.
•
In general, HP service personnel are authorized to perform maintenance
operations in all printer’s parts and subassemblies, but not for the site
electrical infrastructure and printer’s connections to this structure. Safe
isolation of the printer from power prior to service operations shall be done
according to local regulations, and is under the customer’s responsibility.
•
When servicing any electrical components, especially the vacuum pump
cabinet or loader cabinet, turn off the main power switch and padlock it
(see
Figure 1-2
on page 5).
Danger
Only a certified electrician is authorized to carry out any electrical work.
Fuses blown within 36 hours of being replaced may indicate malfunctioning
electrical circuits within the system. Have qualified service personnel check the
system, and do not attempt to replace the fuse again!
Danger
An electrical hazard may exist if any light, monitor, or visual indicator stays ON. To
prevent possible injury, immediately turn OFF the switch in the mains power supply box
on the wall.
Fire Hazards
UV-based inks used with the HP Scitex FB7600 have
flammable
and
irritant
properties. Their combustion products include oxides of carbon.
Danger
Extreme care must be taken when handling inks and solvent to prevent the risk of fire. Do
not permit smoking or naked flames in the print production or storage areas and ensure
that warning signs (see
Figure 1-3
below) are prominently displayed in appropriate
positions.
Figure 1-3
Warning Signs
Always keep two 6 kg fire extinguishers near each HP Scitex FB7600. Never
use water to extinguish a fire! In the event of a fire, switch the electricity
OFF
before extinguishing the fire. Use a carbon dioxide fire extinguisher only.
Danger
Conductive fluids that seep into the active circuit components of the system may cause
short circuits, which can result in electrical fires. Therefore, do not place any liquid or
food on any part of the system.
DANGER: EXPLOSIVE VAPOR, NO SMOKING, NO OPEN FLAMES, NO SPARKS
0